Montigo PVVEX58-300 User Manual

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

Installation & Maintenance Manual

PVHEX58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.

NOTICE

PVHEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.

NOTICE

PVVEX58-300 &
PVVEX510-300

5/8 and 5/10
External Roof
Power Vent

WARNING

If the information in these instructions is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.

Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier, call the fire department.

PVVEX58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.

DANGER

IF YOU SMELL GAS

NOTICE

NOTICE

Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.

NOTICE

This power vent is approved for use with Montigo fireplaces only and is certified to
ANSI Z21.50 / CSA 2.22 vented gas fireplace standard along with the fireplace.

NOTICE

PVVEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.

XG0518 070714

Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248

PVVEX58-300 & PVVEX510-300 Horizontal Power Vent

Safety Alert Key

Introduction

Specications

Pipe Dimensions PVVEX58-300 ...........5"/8"

Pipe Dimensions PVVEX510-300 .........5"/10"

Maximum Airow: .........................300 CFM

Speed: .......................................... 2700 RPM

Power: ...........................................Connect to replace control box

............................................ Refer to replace rating plate

Before Your Begin

General Information

This installation guide covers installation of the External Power Vent

System only. This system is designed to allow installation of gas replaces
that cannot be done with a standard Direct Vent gas replace installa-

tion. Only for use on R-Series, R-Series See-Through and RP-Series.

ONLY USE WITH APPROVED FIREPLACES - see replace

installation manual.

Read through the replace's installation & maintenance manual, as it

must also be adhered to.

Power Cord Harnesses:
EPVH10 - 10 foot power cord and harness
EPVH20 - 20 foot power cord and harness
EPVH30 - 30 foot power cord and harness
EPVH40 - 40 foot power cord and harness
EPVH50 - 50 foot power cord and harness
EPVH60 - 60 foot power cord and harness
EPVH70 - 70 foot power cord and harness
EPVH80 - 80 foot power cord and harness
EPVH90 - 90 foot power cord and harness
EPVH100 -100 foot power cord and harness

For vent congurations and power vent locations,
refer to replace manual.

Page 2

XG0518 - 070714

5"

126

8"

202

PVVEX58-300 Vertical Power Vent Termination

5"

126

8"

202

18

3
8

"

466

16

1

"

24"

610

24"

610

17"

432

17"
432

5"

126

8"

202

PVVEX58-300 Vertical Power Vent Termination

PVVEX58-300 & PVVEX510-300 Horizontal Power Vent

Introduction

PVVEX58-300 Product Dimensions

2

419

7

6

"

8

174

10

267

1
2

"

24"

610

Top View

24"

610

Side View

17"

432

17"

432

Bottom View

8"

202

5"

126

Figure 1. PVVEX58-300 & PVVEX510-300 (Tolerance ± ⅛") [mm]

XG0518 - 070714

Page 3

PVVEX58-300 & PVVEX510-300 Horizontal Power Vent

Installation

PVVEX510-300 Vertical Power Vent Termination

24"

610

10"

253

5"

126

7

6

8

175

24"

610

1

16

"

2

419

3

18

"

8

466

"

13"

330

Figure 1a. PVVEX58-300 & PVVEX510-300 (Tolerance ± ⅛") [mm]

Page 4

18"

458

18"

458

XG0518 - 070714

Power Vent Components

Installation

PVVEX58-300 & PVVEX510-300 Horizontal Power Vent

Installing the power vent

Power Head

Vent Clamp

Framing Box

Vent

Chase

Figure 2. Power vent components Exploded View

Step 2: Install the electrical harness (EPVH-10-100) that will com-

municate with the Power Vent. Run vent pipe from the replace to the
chase. Make sure the last section is female end up and is ush with
the top of the chase without going above it. See gure 2b.

Step 1: Construct a chase box around the vent penetration with

20"

Max

20"

Max

PVVEX58-300

10

270
Min

5

10

8

270

Min

5

"

8

Figure 2b. Installing the Rough-in Kit.

Step 3: Remove the last section of vent pipe and put off to the side

to be used later. Take the rough in box from the power

"

PVVEX510-300
13"
[330]

24

Min

Figure 2a. Chase box dimensions

Note: Follow local and/or national code requirements for roof

clearances.

XG0518 - 070714

Figure 2c. Installing the Rough-in Kit.

Page 5

PVVEX58-300 & PVVEX510-300 Horizontal Power Vent

Installation

Step 4: Unscrew 6 screws securing the control cable cover and
remove it.

Figure 2d. Unscrewing control cable cover

Step 6: Loosen nut on the strain relief of the control cable. Pass

control cable through slot in rough in box making sure the nut stays is
on the opposite side of the rough in box as the strain relief.

Figure 2g.

Step 7: Push the strain relief through the hole in the roughin box.

Figure 2e. Removing control cable cover

Step 5: Unscrew 2 screws securing strain relief plate and remove it.

Strain Relief Plate

Figure 2f. Removing strain relief plate.

Page 6

Figure 2h.

Step 8: Reinstall the strain relief plate. Make sure the strain relief nut

is above the strain relief plate.

Figure 2i.

XG0518 - 070714