Montigo PVHEX58-300 User Manual

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Blank

Installation & Maintenance Manual

PVHEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.

NOTICE

PVHEX58-300 &
PVHEX510-300

5/8 and 5/10
External Wall
Power Vent

WARNING

If the information in these instructions is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.

DANGER

Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier, call the fire department.

PVHEX58-300 power vent is approved for use with Montigo R320, R320-ST, R420,
R420-ST, and RP620.

IF YOU SMELL GAS

NOTICE

NOTICE

Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.

NOTICE

This power vent is approved for use with Montigo fireplaces only and is certified to
ANSI Z21.50 / CSA 2.22 vented gas fireplace standard along with the fireplace.

NOTICE

PVVEX510-300 power vent is approved for use with Montigo R520, R520-ST,
R620-ST, R720, and R820.

XG0517

Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248

070714

PVHEX58-300 Horizontal Power Vent System

Safety Alert Key

Introduction

Specications

Pipe Dimensions PVHEX58-300 ...........5"/8"

Pipe Dimensions PVHEX510-300 .........5"/10"

Maximum Airow: .........................300 CFM

Speed: .......................................... 2700 RPM

Power: ............................................Connect to replace control box

............................................ Refer to replace rating plate

Before Your Begin

General Information

This installation guide covers installation of the External Power Vent

System only. This system is designed to allow installation of gas replaces
that cannot be done with a standard Direct Vent gas replace installa-

tion. Only for use on R-Series, R-Series See-Through and RP-Series.

ONLY USE WITH APPROVED FIREPLACES - see replace

installation manual.

Read through the replace's installation & maintenance manual, as it

must also be adhered to.

Power Cord Harnesses:
EPVH10 - 10 foot power cord and harness
EPVH20 - 20 foot power cord and harness
EPVH30 - 30 foot power cord and harness
EPVH40 - 40 foot power cord and harness
EPVH50 - 50 foot power cord and harness
EPVH60 - 60 foot power cord and harness
EPVH70 - 70 foot power cord and harness
EPVH80 - 80 foot power cord and harness
EPVH90 - 90 foot power cord and harness
EPVH100 -100 foot power cord and harness

For vent congurations and power vent locations,
refer to replace manual.

Page 2

XG0517 - 070714

Product Dimensions

5"

127

8"

203

PVHEX58-300 External Horizontal Power Vent

2"51

13"
330

19

7
8

"

505

9

1
2

"

241

6

1
8

"

156

15

7
8

"

403

13"

330

13"

330

5"

127

8"

203

PVHEX58-300 External Horizontal Power Vent

Power Head

PVHEX58-300 & PVHEX510-300 Horizontal Power Vent

Introduction

1

22

"

4

566

18

465

1

"

4

1

21

"

4

541

17

439

1

"

4

1

4

"

2

114

Front View

13"

19

330

9

241

505

2"51

1

"

2

7

"

8

1

6

"

8

156

Top View

7

13"

15

"

8

PVHEX58-300

8"

203

PVHEX10-300

254

10"

Rear View

5"

127

403

Framing Kit

330

Side View

13"

330

Electrical Box

Vent Retainer

Figure 1. PVHEX58-300 & PVHEX510-300 (Tolerance ± ⅛") [mm]

XG0517 - 070714

Page 3

PVHEX58-300 & PVHEX510-300 Horizontal Power Vent

Installation

Installing the Power vent

1

"

14

2

368

Framing

15

389

Unpacking the Power vent

Step 1: Unscrew Power Head from rough in Box by unscrewing four
screws.

1

"

4

Figure 2a. Unscrewing four screws

Wall board

Rough in box

Figure 2. Framing dimensions (combustible material construction)

Figure 2b.

Step 2: Remove Power head from rough in box.

Page 4

Figure 2c.

XG0517 - 070714

Installation

PVHEX58-300 & PVHEX510-300 Horizontal Power Vent

Step 3: Screw rough in box to wall.

Step 5: Remove electrical cover.

Figure 2f.

Step 6: Remove two screws securing the strain relief plate.

Figure 2d.

Step 4: Remove six screws securing the electrical cover.

Figure 2e.

Figure 2g.

Step 7: Remove Strain Relief Plate.

Figure 2h.

XG0518 - 070714

Page 5

PVHEX58-300 & PVHEX510-300 Horizontal Power Vent

Installation

Step 8: Take the electrical harness (EPVH-10-100) that will commu­nicate with the Power vent and pass the cable through the slot in the
rough box. Make sure the nut for the strain relief is inside the box and
the strain relief is outside the box.

Figure 2i.

Step 9: Reinstall the strain relief plate underneath the strain relief nut

and screw the strain relief plate down. Then tighten strain relief nut.

Step 11: Secure the electrical cover back down with the six screws
making sure the control cable curls up safely.

Figure 2l.

Step 12: Pass the vent pipe through the rough in box so it extends

6 1/2 inches into the rough in box.

Figure 2j. Removing control cable cover

Step 10: Push the molex connector through the hole in the electrical

cover until it clicks into place.

Click

6 1/2 "

Figure 2m.

Figure 2k.

Page 6

Figure 2n.

XG0517 - 070714