Montigo Proflame 2 Upgrade Kit RX 200 NG, Proflame 2 Upgrade Kit RX 200 LP Installation Manual
Proame 2 Upgrade Kit RX 200 NG/LP
US
Upgrade Kit NG/LP Proame 2 (Basic to Full
Load with Remote)
This kit is for use with the following models:
B34DT-2-F : B34 Top Vent, Electronic Ignition, IPI
B34DR-2-F : B34 Rear Vent, Electronic Ignition, IPI
B38DT-2-F : B38 Top Vent, Electronic Ignition, IPI
B38DR-2-F : B38 Rear Vent, Electronic Ignition, IPI
The installation of this kit must be done by a qualied and
®
certied gas appliance installer.
Upgrade Kit
C
Check local codes and read all instructions prior to installation.
CAUTION
Ensure that all power to the appliance is off at the electrical breaker or fuse
before beginning installation. Ensure gas is turned off at the shutoff valve before
beginning installation.
Warning: If the information in these instructions is not followed
exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
What To Do If You Smell Gas:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
Page 1
XT0016 - 092214
Installation
Table of Contents
A. Disconnect Control Module and Harness: 3
B. Stepper Motor Installation: 4
C. Control Module Installation: 5
D. Main ON/OFF Switch Installation: 6
E. Battery Holder Installation: 7
F. Operation with Backup Battery: 7
G. Operation with MAIN Power: 7
General Information
This blower kit is for installation with the models listed above.
KIT # Contents
RX200NG Control Module, Remote Control, Stepper Motor-NG,
Manual Override switch with harness and bracket,
backup battery pack, Proame 2 operations manual,
hardware and batteries.
RX200LP Control Module, Remote Control, Stepper Motor-LP,
Manual Override switch with harness and bracket,
backup battery pack, Proame 2 operations manual,
hardware and batteries.
Before You Begin
Ensure that the power supply has been turned off at the breaker or
fuse before beginning the installation.
Shut off the gas supply at the shut-off valve, and ensure that the main
burner and pilot light have been turned off and the replace has been
cooled off for at least two hours before installation.
Battery Pack
Stepper
Motor-NG
or LP
Control Module
Remote Control
Proame 2 Operations
Manual
Hardware and
batteries
Manual override
switch with harness
and bracket
General Information
This upgrade kit contains the necessary components for field upgrade of an approved Montigo fireplace from Proflame 2 basic control
system to Full Load with remote.
The installation of this unit must also conform with local codes or, in
the absence of local codes, with the American National Fuel Gas
Code, ANSI Z223.1, or the Canadian Installation Code, CAN / CGA
B149.
WARNING!
This upgrade kit shall be installed by a qualified service
agency in accordance with the manufacturer's instructions
and all applicable codes and requirements of the authority
having jurisdiction. If the information in these instructions
are not followed exactly, a fire, explosion or production of
carbon monoxide may result causing property damage,
personal injury or loss of life. The qualified service agency
is responsible for the proper installation of this kit. The
installation is not proper and complete until the operation
of the converted appliance is checked as specified in the
manufacturer's instructions supplied with this kit.
Note
Upon successful installation of this upgrade kit, the following features are available for the user:
1. Thermostatic and smart thermostatic control of the
replace
2. Main burner ame modulation (6 levels)
3. Choice of Standing or Intermittent pilot (CPI switch
required / not supplied)
4. Comfort fan speed modulation (Remote Fan Kit
RFK3002R or RFK3004R required)
5. Battery backup for the main burner during power outage
Tool Required
T20 Torx bit
Impact gun / Drill
1/4 " Nut driver bit
Figure 1 Contents of Proame 2 Upgrade Kit
Note: You may remove the front cover (See Figure 2), or the
burner assembly to access the control module and wiring. If
removed, please ensure it is re-installed properly and all gas
connections are leak tested.
Page 2
Figure 2 Fireplace front cover
XT0016 - 092214
Installation
A. Disconnect Control Module and Harness:
1. Disconnect Control Module Powercord from the PPO box.
5. Remove the connector from X1 of the control module.
Figure 3 Powercord in PPO box
2. Disconnect Spark Wire and Sensor Wire from connectors X2 and X3 of the control module.
3. Disconnect the wall switch harness from X4 Control
Module and discard.
Figure 4 Control module with wires
4. Remove the Valve Harness from X5 of the control module.
Figure 6 X1 plug of control module
6. Remove the control module from firebox compartment and
discard. Note: module is attached by velcro strips.
Figure 5 X5 plug of control module
XT0016 - 092214
Page 3
Loading...