Montigo H34 User Manual
Installing the H34/H38/H42 Surround
April-01-15 8:18:44 AM
for use with:
H-Series; H34-DF
H-Series; H38-DF
®
H-Series; H42-DF
C US
3
1
Parts Included
1) 1-Pc, Surround
2) 2-Pcs, Attachment Brackets
3) 4-Pcs, Moving Brackets
4) 1-Pkg. Hardware
O
2
Tools Required
1) Power Drill, (eight 1/8" holes)
2) #8 Hexhead Driver, (to match hardware)
3) Carpenters level (Final Step, if required)
4
Installing the Surround
To install the Montigo Stainless steel or Black contemporary
surround to the H34DF, H38DF, or H42DF follow these steps.
Step 1. Mark the location of the holes needed.
From the package of hardware locate one of the Attachment
Brackets. Hold this part in place as shown in Figure 2. With a pen-
cil or pen mark the (6) six holes on the face of the replace frame,
(see Figure 2.) Note: Ensure the brackets align with Figure 2. Below.
Moving Brackets (2)
(Left and Right side Typical)
Align (2) attachment brackets
on center of frame verticals
(Left and Right side Typical)
1”
Brackets to be
flush with top of
fireplace frame,
(Typical)
H34DF
H38DF
H42DF
N
M
Surround Dimensions
M N O P
31 7/16" 24 1/4" 45 15/16" 38 7/8"
35 3/16" 26 3/8" 49 11/16" 41"
39 5/8" 30 7/16" 54 1/8" 45 1/16"
P
Figure 1. Surround Dimensions (tolerance within 1/16")
XG0903 - 150204
Bracket to be
Flush with
outside edge
Mounting Holes (3) per side.
(Left and Right side Typical)
Figure 2. Bracket Alignment
of fireplace,
(Typical)
Step 2. Drill holes.
Before you go any farther now is the time to double check the loca-
tion of the holes, do they agree with Figure 2. If you are satised
with the location of the holes, use a punch to mark the holes, then
using a 1/8" drill, drill out the six holes.
f i r e f e a t u r e
Step 3. Install the (2) two Attachment Brackets. (See Figure 2)
FLUSH WITH
VALVE/BOTTOM
PANEL
March-31-15 12:54:25 PM
March-31-15 12:54:25 PM
April-01-15 8:18:44 AM
Install the two (2) Attachment Brackets you used as a guide. Have
someone hold one of the Brackets in place, using the Hex-tool,
place a self-tapping #8-18 sheet metal hex screw into the hole
and twist it into the hole half way
.
Follow this procedure for the remaining two (2) screws in the rst
bracket. After the three (3) screws are in place tighten them in
place. Repeat the procedure in Step 3 for the second Attachment
Bracket.
Step 4. Install the (2) two Movable Brackets. (If installed disregard this
step. If not See Figure 3)
Install the two (2) Movable Brackets. (These move up or down to level
and align the surround. This will produce a symmetrical reveal
when correctly adjusted).
Moveable Bracket
10-24 Machine Screw
Cut out
Figure 3. Installing the Movable Brackets
Pick up one of the brackets, using the supplied hardware, mount it into
place. Slide the bolt through the bracket 'front to back', (See Figure 3), then tighten the bolt using a open end wrench or socket.
Follow this procedure for the remaining bolt in the second Movable
Bracket.
Step 5. Installing the Lower Moveable Brackets
Using the self drilling screws supplied secure the moveable
brackets to the front of the replaces lower facia. The cut out on
the moveable braket should be such that the cut out is facing up.
The moveable bracket should be level with the top of the replace
lower facia and spaced evenly from left to right as to support the
weight of the surround. See gure 4 and 5.
Cut Out
Lower Facia
Moveable Bracket
Figure 5. Installing the Movable Brackets on Lower Facia
Step 6. Placing the Surround
Finally it's time to install the Stainless steel or Black Surround.
For this step it would be helpful to have someone help you hold
the surround in place.
Lift the surround over the four (4) Movable Brackets and slide the
surround downward. The surround should securely lock in place
in the cut out in the lower moveable brackets. Center the surround left to right.If the surround doesn't clear the top or bottom
of the replace you will have to adjust the movable brackets up
or down. Remove the surround place it aside. Adjust the bracket
as required. Repeat as necessary.
Step 7. Final adjusting of the Surround
This step is not necessary if the surround ts tightly around the
replace, or the adjustment is acceptable. But, if your surround
has an uneven reveal, or unequal gap around/between the replace and surround, using a carpenters level adjust the Movable
brackets as needed.
Finally place the adjusted Surround back on the Brackets and admire
your Contemporary Montigo replace.
Moveable Bracket
XG0903 - 150204
Lower Facia
Figure 4. Installing the Movable Brackets on Lower Facia
WARNING
When installing the replace - gas lines, ttings,
accessories or any other objects cannot impede the
proper movement of the door buckles.
WARNING
Screen Barrier must still be used with the Surround.
The screen should only ever be removed for servicing and then reinstalled before operating replace.
Loading...