Montgomery Ward TMO-3395309, TMO-3100002 Operating Manual

Download

Page 1

42" Lawn Tractors

Operating Manual

Model Nos. TMO-3100002

TMO-3395309

Model TM0-3395309 Shown

Mom_me_ Wazd

Page 2

INDEX

Rules for Safe Operation ............................................ 3

Assembly Instructions ................................................. 4

Controls ...................................................................... 7

Operation .................................................................... 9

Adjustments .............................................................. 10

Lubrication ................................................................ 13

Maintenance ............................................................. 13

Off-Season Storage .................................................. 17

Trouble Shooting Guide ...................................... 18, 19

Electrical System ...................................................... 19

Illustrated Parts for Lawn Tractors ....................... 20-30

Slope Gauge ............................................................. 31

Parts Information ........................................ Back Cover

Dear Customer,

So often throughout the year we are all in a

rush to meet our daily obhgations.

However, we at Montgomery Ward are taking

a quick moment out to say...

"Thank you for your business."

Sincerely,

MONTGOMERY WARD

_ NSTRUCTIONS GIVEN WITH THIS SYM- I

BOL ARE FOR PERSONAL SAFETY. BE SURE TO FOLLOW THEM.

NOTICE: A data plate with the model number and serial numbers of your unit is located on the frame, under the seat. Record these numbers in the spaces provided on the back cover of this guide.

BEFORE YOU CALL SERVICE

Check Spark Plug Wire

• Firmly attached?

• Wire terminal clean?

Check Crankcase Oil Level

• Overfilled/underfilled?

Check Fuel Tank

• Fuel in tank?

• Fuel dirty or stale?

• If tank has been empty for a long period, fill tank completely.

Check Air Cleaner

• Clean?

• Choke plate stuck?

• Governor spring free to move?

Check under Blade Housing (Disconnect Spark Plug First)

• Blade obstructed or bent?

Check Starting Instructions

• Read instruction manuals and labels for specific instructions.

WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unim- proved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in

effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands, A spark arrester for the muffler is avail- able through your nearest engine authorized service center or contact the parts sales center of Montgomery Ward.

Page 3

IMP0RTANT sA,=,=oP,=.,,-.o.

,_k THIS SYMBOLPOINTSOUT IMPORTANTSAFETYINSTRUCTIONSWHICH, IFNOT FOLLOWED,COULD ENDANGERTHEPERSON-

AL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFOREATTEMPTINGTO OPERATEYOURUNIT.WHENYOU SEETHIS SYMBOL-- ,_ HEEDITS WARNING.

,L_ This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe

41dk

DANGER: thefollowing salety instructionscould result in seriousinjury or death.

I. 6ENERAL OPERATION

1. Read,.understand,and follow all instructions in the manual and

on the machine before starting. Keep this manual in a safe place for future reference and for ordering replacement parts.

2. Only allow responsible adults familiar with the instructions to operate the machine. Know controls and how to stop the machine quickly,

3. Do not put hands or feet under cutting deck or near rotating parts.

4. Clear the area of objects such as rocks, toys, wire, etc. which could be picked up and thrown by the blade. A small object may have beenoverlooked and could be accidentally thrown by the mower in any direction and cause injury to you or a bystander. Always wear safety glasses or eye shields during operation or while performing an adjustment or repair, to pro- tect eyes from foreign objects. Stop the blade(s) when cross-

ing gravel drives, walks or roads_

5. Be sure the area is clear of other people before mowing. Stop

machine if anyone enters the area.

6 Never carry passengers.

7. Disengage blade(s) before shifting into reverse and backing up. Always look bown and behind before and while backing.

8. Beaware of the mower and attachment discharge direction and

do not point it at anyone, Do not operate the mower without either the-entire grass catcher or the chute guard in place,

9 Slow down before turning. Operatethe tractor smoothly. Avoid

erratic operation and excessive speed.

10 Never leave a running machine unattended. Always turn off

blade(s), place transmission in neutral, set park brake, stop engine and remove key before dismounting.

11 Turn oft blade(s) when hal mowing.

12. Stop engine and wait until blade(s) comes to a complete stop before (a) removing grass catcher or unclogging chute, or (b) making any repairs, adjusting or removing any grass or debris.

13. Mow only in daylight or good artificial light.

14. Do not operate the machine while under the influence of alco- hol or drugs.

15, Watch for traffic when operating near or crossing roadways.

16. Use extra care when loading or unloading the machine into a trailer or truck. This unit should not be driven up or down a

ramp onto a trailer or truck under power, because the unit Could tip over, causing serious personal injury, The unit must be pushed manually to load or unload properly

17. Never make a cutting height adjustment while engine is run-

ning if operator must dismount to do so,

18. Wear sturdy, rough-soled work shoes and close-fitting slacks

and shirts. Do not wear loose fitting clothes or jewelry. They can be caught in moving pads. Never operate a unit in bare feet, sandals, or sneakers.

19. Check overheadclearance carefully before driving under power

lines, wires, bridges or low hanging tree branches, before entering or leaving buildings, or in any other situation where the operator may be struck or pulled from the unit, which could result in serious injury.

20. Disengage all attachment clutches, thoroughly depress the

brake pedal, and shift into neutral before attempting to start engine.

II. SLOPEOPERATION Slopes are a major factor related to loss of control and tip-over accidents which can result in severe injury or death. All slopes require extra cautLon If you cannot back up the slope or if you feel uneasy on it, do not mow it.

DO:

Mow up and down slopes, not across Remove obstacles such as rocks, limbs, etc. Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass canhide obstacles, Use slow speed. Choose a low enough gear so that you will not haveto stop or shift while on the slope. Always keep,tractor in gear when going down slopes to take advantage of engine braking action..

Follow the manufacturer's recommendations for wheel weights or counterweights to improve stability. Use extra care with grass catchersor other attachments. These can change the stability of the machine. Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Rapid engagement or brak-

ing could cause the front of the machine to lift and rapidly flip over

backwards which could causeserious injury. Avoid starting or stopping on a slope. If tires lose traction, disen- gage the blade(s) and proceed slowly straight down the slope.

Foryour safety, usethe slope gauge included as part o! this manual to measure slopes before operating this unit on a sloped or hilly

area. If the slope is greater than 15° as shown on the slope gauge,

do not operate this unit on that area or serious injury could result.

DONOT:

Do not turn on slopes unless necessary; then, turn slowly and

gradually downhill, if possible.

13onotmow near drop-offs, ditches or embankments. A wheel over the edge or an edge caving in could cause sudden overturn,

Do not mow on wet grass. Reduced traction could cause sliding.

Do not try to stabilize the machine by putting your foot on the

ground.

Do not use grass catcher onsteep slopes.

ill. CHILOREM

Tragic accidents can occur if the operator is not alert to the pres-

ence of children. Children are often attracted to the machine and

the mowing activity. Never assume that children will remain where

you last saw them

1. Keep children out of the mowing area and in watchful care of an adult other than the operator.

2. Bealert and turn machineoff if children enterthe area.

3. Before and when hacking, look behind and downfor small chil- dren.

4. Nevercarry children. They may fall off and be seriously injured or interfere with the safe machine operation.

5, Never allow children under 14 years old to operate the

machine. Children 14 years and over should only operate machine under close parental supervision and proper instruc-

tion.

6, Use extra care when approaching blind corners,shrubs, trees

or other objects that may obscure vision.

Page 4

IV._r,BYJ£_

1.Useextracareinhandlinggasolineandotherfuels.They are

flammable and vapors are explosive. a. Useonly an approved container. b. Never remove gas cap or add fuel with the engine running

Allow engine to cool at least two minutes before refueling.

Do not smoke. c. Never refuel the machine indoors. d. Never store the machine or fuel container inside where

there is an open flame, or spark, s_ch as a water heater.

spaceheater, clothes dryer and the like.

2. Neverrun a machine inside aclosed area.

3. Check frequently and keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in safe working condition.

4. Never tamper wilh safety devices. Checktheir proper operation regularly. Use all guards asinstructed in this manual.

5 To reduce fire hazard, keep machine free of grass, leaves or

other debris build-up. Clean up oil or fuel spillage. Allow machine to cool before storing.

6. Stop and inspect the equipment for damage if you strike an object. Repair, if necessary, before re-starting and operating

the machine

7. Nevermakeadjustments or repairswith the engine running.

8. Grass catcher components are subjecl to wear. damage and deteriorate, which could expose moving parts or ailow objects to be thrown. Frequently, check components and replace with manufacturer's recommended parts when necessary. Mower blades are sharp and can cut. Wrap the blade(s) or wearglovesand useextra caution when serwcmg blade(s). Check brake operation frequently. Adjust and service as required.

Muffler engine, and belt guards become hot during operation andcan causea burn. Allow to cool down before touching Do not change the engine governor settings or overspeed the

engine.

10.

11.

12.

I ,_ Your unitwas built Io be operated according to the rulesfor safe operation in this manual. As with any type

DANGER: of power equipment, carelessnessor error on the part ofthe operator can resull in serious injury. If you viu-

late anyof these ru!es,you may cause seriousinjury toyoursell or others.

ASSEMBLY INSTRUCTIONS

IMPORTANT: After assembly, service engine with gasoline, and check oil level as instructed in the separate engine manual packed with your unit.

NOTE: Reference to right or left hand side of the unit is observed from the driver's seat, facing for-

ward.

Self-Tapping Screws

UNPACKING

1. Remove the lawn tractor from the carton as fol- lows. Open the top flaps. The loose parts (include

the battery fluid, steering wheel with steering cap

attached and chute deflector) are on the seat and

wrapped in plastic. Remove all carton inserts. Cut the front corners of the carton. Make certain

brake is released, and push the unit out of the

carton.

2. The seat has been mounted backward for ship- ping purposes. Carefully cut and remove the plas- tic wrap. Remove the loose parts from the seat.

FIGURE 1.

-_--ASSEMBLING THE SEAT

Remove the hex self-tapping screws which secure the seat to the seat pivot bracket. Turn the seat around

and place in position against the seat pivot bracket, lining up the slotted holes in the pivot bracket with the holes in the seat. Select desired position for the seat, and secure with hex self-tapping screws. See figure 1.

'BATTERYINFORMATION

WARNING D.

A. Battery acid must be handled with great care as

contact with it can burn and blister the skin. It is also advisable to wear protective clothing (goggles,

rubber gloves and apron) when working with it.*

B. Should battery acid accidentally splatter into the

eyes or onto the face, rinse the affected area immediately with clean cold water. If there is any

further discomfort, seek prompt medical attention.

C. If acid spills on clothing, first dilute it with clean

water, then neutralize with a solution of ammonia/

water or baking soda/water.

Since battery acid is corrosive, do not pour it into

any sink or drain. Before discarding empty elec- trolyte containers, rinse them with a neutralizing

solution.

NEVER connect or disconnect charger clips to battery while charger is turned on as it can cause sparks.

Keep all lighted materials (cigarettes, matches, lighters) away from the battery as the hydrogen gas generated during charging can be combustible. As a further precaution, only charge the battery in

a well-ventilated area.

*Always shield eyes, protect skin and clothing

when working near batteries.

Page 5

,;_Battery

Cover

Battery

Vent

Elbow

Clear Plastic

Drain Tube

Screwdriver

Caps

FIGURE 2.

FIGURE 3.

DANGER

Battery contains sulfuric acid. Refer to-warning

on page 4. Antidote: EXTERNAL--Flush with water. INTERNAL--Drink large quantities of water or milk. Follow with milk of magnesia, beaten eggs or vegetable oil. Call physician immediately. EYES:

Flush with cool water for at least 15 minutes, then

get prompt medical attention.

Since batteries produce explosive gases, keep

all lighted materials (cigarettes, lighters, match- es, etc.) away. Be sure to charge battery only in

well-ventilated areas. Make certain venting path of battery (drain tube) is always open.

KEEP BATTERIES

OUT OF THE REACH OF CHILDREN!

ACTIVATINGTHE BATTERY

Do not activate battery (fill with battery acid) until battery is actually placed in service. Be certain to read previous warnings before activating the bat- tery.

1. Lift the seat. Remove the battery cover by press-

ing in on the sides and lifting up. See figure 2

inset. Remove the battery from the rear frame.

2. Open the battery pack. Be careful not to puncture the box. It contains the battery fluid (acid) in a plastic container and one short plastic tube.

3. Place the battery on a table or workbench. Make certain the long plastic drain tube is in place on the vent elbow.

4. Remove the six fill caps from the top of the bat- tery with a screwdriver. Be careful not to damage the fill caps. See figure 2.

5. Place the battery fluid container on the table or workbench. Carefully cut off tip of the spout and attach the short plastic tube provided. Do not squeeze the container when cutting tip.

6. Fill each battery cell slowly and carefully to the

UPPER LEVEL line marked on battery. See fig- ure 3. Use caution as the acid level will rise rapid- ly alter the bottom of the cell is filled.

7. Allow battery to stand for 30 minutes with the fill

caps removed, while the plates absorb acid.

8. If acid level has fallen after the 30 minute stand-

ing period, refill each cell with battery acid to the UPPER LEVEL line on battery. Replace the fill

caps.

9. Before discarding the empty container, neutralize

any residue with baking soda and rinse container with water. Puncture container several times

before discarding.

10. Charge the battery after the 30 minute standing

period. SLOW CHARGE THE BATTERY (DO NOT FAST CHARGE).

Charge the battery at a maximum bench rate of 2 amperes until the specific gravity reading is 1.265. Charge for a minimum of 3 hours and a maximum of 5

hours.

NOTE: This engine is equipped with an alternator. The current for the battery charger alternator is unreg- ulated. During normal operation, it is only necessary to charge the battery:

1. When it is activated for the first time.

2. Before winter storage.

3. Before using the lawn tractor after winter storage.

After battery has been charged, add only distilled water. Do not add acid.

Page 6

Steerin

Cap

Steering

Bellow

FIGURE 4.

_..._- Hex Nuts

\_ Washers

;//_..._ _ .'Machine

.--_--_--S".E..2/JI._', ',Screws

"" ',II

='-'7;' u ii',

// l'i

FIGURE 5.

Deck Hanger ___

FIGURE 6.

Lock

Nut

Washer

AllACHING THE STEERING WHEEL

1. Remove the hex lock nut and cupped washer

from the steering shaft, and remove the steering

bellow. Pry the steering cap off the center of the

steering wheel.

2. Attach one end of steering bellow to the steering

-<------ wheel as shown in figure 4, inset.

3. Position the front wheels of the tractor so they are pointing straight forward.

4. Place the steering wheel and steering bellow over the steering shaft, positioning steering wheel as

desired.

5. Place the washer with the cupped side down over

the steering shaft. Secure with hex lock nut. See figure 4.

6. Place the steering cap over the center of the steering wheel and seat it with your hand.

ATTACHINGTHE CHUTE DEFLECTOR

The chute deflector must be attached to the right side of the deck so that it covers the chute opening.

WARNING: Do not operate your unit unless the chute deflector has been

properly installed.

Make certain deck is raised to its highest position (lift lever pulled all the way back).

Remove the truss machine screws, cupped wash-

ers and hex nuts which are attached to the deck

next to the chute opening.

Place the chute deflector in position as shown in figure 5. Secure with hardware just removed. Cupped side ol washers goes against the chute

deflector.

LEVELING THE DECK

With unit on hard, level surface, measure the distance

from the bottom edge of the center of the left side of

deck to the ground. Measure the same distance just

behind the chute area on the right side of the deck. Or, place the blades in a straight line, and measure the distance from the outside edge of the blade tips to the ground.

If adjustment is needed, proceed as follows.

1. Remove the hairpin clip and flat washer from the bottom of the adjustable lift link on the left side of the deck. (Hairpin clip and flat washer are on the

inside of the lift link.) Pull the adjustable lift link out of the deck hanger

channel. See figure 6. Turn the adjustable lift link up or down as neces-

sary to level the deck. Usually only one or two turns are needed.

4. Insert the end of the adjustable lift link into the hole in the deck hanger channel. Recheck the adjust- ment as instructed above. Readjust if necessary.

5. When deck is level, secure the end of the adjustabre lift link with flat washer and hairpin clip.

Page 7

Battery

Drain TubeI

.Negative

Terminal

Positive

:rminal

TIRE PRESSURE

The tires on your unit may be over-inflated for ship-

ping purposes. Reduce the tire pressure before oper- ating the unit. Recommended operating tire pressure is approximately 12 p.s,i. (check sidewall o! tire for tire manufacturer's recommended pressure).

Red

Black (Positive)

(Negative) Cable

Cable

FIGURE 7. Drain

Cable Tube

Transaxle Tie_

" Re' _lfra%Ckeel_lent _

FIGURE 8.

CONTROLS

WARNING: Maximum tire pressure under

any circumstances is 30 p.s.i. Equal tire

pressure should be maintained on all tires,

_-INSTALLING THE BATTERY

1. Raise the seat.

2. Make certain the positive cable (heavy red wire) and negative cable (heavy black wire) are routed outside the battery opening.

3. Place the battery inside the opening so that the

positive terminal is toward the front of the unit. See figure 7. Route the battery drain tube down

beside the battery.

4. Remove the hex bolt from the positive (+) termi- nal, Place the positive cable on the positive termi- nal. See figure 7. Secure with hex bolt, Be careful

not to lose the nut inside the terminal.

5. Secure the negative cable to the negative (-) ter- minal in the same manner. Replace the battery cover over the positive terminal. Lower the seat.

6. Insert the drain tube through the cable tie which is attached to the transaxle reinforcement bracket

on the right side of the unit. See figure 8. Be cer- tain drain tube is routed away from the wheel rim.

Pull on end of cable tie to tighten (do not collapse

drain tube). Trim excess end of cable tie.

Clutch-Brake

Pedal

Ignition

Throttle

Control

Ammeter

Light Switch

Shift

Lever Choke

FIGURE 9.

THROTI'LE CONTROL

The throttle control is used to regulate the engine speed. To get maximum efficiency from cutting, the throttle should be in the FAST position when operat-

ing the mower. See figure 9.

CHOKECONTROL

The choke control is located on the dashboard and is

operated manually. Details for the choke operation are covered in the separate engine manual packed

with your unit. See figure 9.

SHIFT LEVER

The shift lever is located in the center of the console

and has three positions, FORWARD, NEUTRAL and

REVERSE. See figure 9. The clutch-brake pedal must

be depressed and the lawn tractor must not be mov- ing when shifting gears. Do not force the shift lever.

Release the clutch-brake pedal slightly to line up the shifting collar in the transmission. Then try to shift gears.

SPEED CONTROL LEVER

The speed control lever is located 'on the fender. See figure 10. The speed control lever allows you to regu-

late the ground speed of the lawn tractor. To select

the ground speed, depress clutch pedal. Move speed

Page 8

controlleveroutofthenotchesandbackwardto slow lawntractor,forwardto increasespeed.Whendesired

speedhasbeenobtained,releaseleverinthatposi- tion.Wheneverclutchisengaged, unit will automati-

cally go to the pre-set speed.

IGNITION SWITCH

Turn the key to the START position to start the engine. When the engine is running, let the key return

to the ON position. To stop the engine, turn the key to the left to the OFF position and remove it to prevent accidental starting. See figure 9.

LIGHT SWITCH

Push the light switch to turn on the lights. The lights

will only operate when the engine is running.

AMMETER

The ammeter registers the rate of battery charge or discharge. The ammeter will register on the discharg- ing side when starting lhe engine. It should register on the opposite side (charging) when the engine is run- ning in the fast position until the battery is completely charged. With a fully charged battery or with the engine idling, the ammeter will not show a charge. See figure 9.

CLUTCH-BRAKE PEDAL

The clutch-brake pedal is located on the left side of the lawn tractor. Depressing the clutch-brake pedal

part way disengages the clutch. Pressing the pedal all the way down disengages the clutch and engages the disc brake. See figure 9.

NOTE: The clutch-brake peda! must be depressed to

start the engine.

the notches to the desired position. Release the speed control lever and the clutch-brake pedal.

NOTE: The parking brake must be set ff the operator

leaves the seat with the engine running.

INTERLOCKS (Not Shown)

Interlock safety switches are located by the clutch- brake pedal, the lift lever, the shift lever and under the

seat. Before the engine will start, the clutch-brake pedal

must be depressed all the way and the lift lever must be in the disengaged position.

Before the unit can be shifted into reverse or if the operator leaves the seat, the lift lever must be in the disengaged position.

CUTTING CONTROLS

A. LIFT LEVER

The lift lever is used to raise and lower the cutting deck and to engage and disengage the blades. Pulling it all the way back and locking it disengages

the blades. NOTE: The lift lever must be in the disengaged posi-

tion when starting the engine, when shifting into reverse and if the operator leaves the seal See figure

11.

B. DECK LIFT INDICATOR

The deck lift indicator marks the position being used for the lift lever. Select the lift lever position desired, press the indicator lever outward, move it to the posi- tion immediately below the lift lever and release the indicator lever. See figure 11.

_peed

Control

FIGURE 10.

PARKINGBRAKE

The speed control lever is used to set the parking

brake. To set the parking brake, depress the clutch- brake pedal. Move the speed control lever out of the notches to desired position. Release the speed con- trol lever and the clutch-brake pedal.

To release the parking brake, depress the clutch- brake pedal and move the speed control lever out of

FIGURE 11.

¢k Lift

Indicator

C. SETTING THE CUTTING HEIGHT

1. Select the position for the lift lever which gives the desired cutting height. Move the deck lift indi- cator so that the lift lever can be returned to the same position after it is raised.

2. Move the deck wheels to the hole location so the wheels are 1/4 to 1/2 inch above the ground.

Page 9

OPERATION

WARNING

AVOID SERIOUS INJURY OR DEATH

GOUP AND DOWN SLOPES,NOTACROSS.• AVOID SUDDENTURNS. DO NOT OPERATE]-HEUNIT WHERE ITCOULDSLIP OR TIP.

IF MACHINE STOPS GOING UPHILL, STOP BLADE(S) AND BACK DOWNHILL SLOWLY. DO NOT MOW WHENCHILDRENOROTHERSAREAROUND.

NEVERCARRY CHILDREN. LOOK DOWNAND BEHIND BEFOREANDWHILE BACKING. KEEP SAFETY DEVICES (GUARDS, SHIELDS, AND SWITCHES) IN

PLACEAND WORKING. REMOVEOBJECTSTHAT COULD BETHROWN BYTHE BLADE(S).

KNOW LOCATIONAND FUNCTIONOFALL CONTROLS. BE SURE BLADE(S) AND ENGINE ARE STOPPED BEFORE PLACING HANDS OR FEETNEARBLADE(S).

BEFORE LEAVING OPERATOR'S POSITION, DISENGAGE BLADE(S), PLACE THE SHIF'[ LEVERIN NEUTRAL,ENGAGE BRAKELOCK, SHUT

ENGINEOFFAND REMOVEKEY

READ OPERATOR'S MANUAL

GAS AND OIL FILL-UP

Check oil level and add if necessary. Service the engine with gasoline as instructed in the separate engine manual packed with your tractor. Read instructions carefully.

IMPORTANT: Your tractor is shipped with oil; howev- er, you must check the oil level before operating. Be

careful not to overfill.

WARNING: Never fill fuel tank indoors,

with engine running or while engine is hot.

3.. Set the throttle control in the FAST position. See figure 9.

4. Pull out choke knob to choke engine (a warm engine may not require choking).

5. Turn the ignition key to the START position. When the engine is running, let the key return to the ON position. See figure 9.

6. Push choke knob in gradually. Move the throttle control to desired engine speed.

STOPPING THE ENGINE

Turn the ignition key to the left to the OFF position.

Remove the key to prevent accidental starting.

IMPORTANT; If you strike a foreign object, stop the engine. Remove wire from spark plug, thoroughly inspect the unit for any damage, and repair the dam- age before restarting and operating the mower.

NOTE: If any problems are encountered, refer to the

Trouble Shooting Guide on page !8.

OPERATING THE LAWN TRACTOR

1. Set the desired cutting height.

2. Start the engine as instructed previously.

3. Move throttle control to 3/4 or full throttle to pre- vent strain on the engine and to operate the cut- ting blades.

4. Place the shift lever in either the FORWARD or

REVERSE position.

STARTING THE ENGINE

1. Depress the clutch-brake pedal and set the pa_'k- ing brake.

2. Place the lift lever in the DISENGAGED position. See figure 11.

IMPORTANT: This unit is equipped with a safety interlock system for your protection. The purpose of

the safe_y in½er!ock system ;_ to preven_t th_ _ngino

from cranking or starting unless the clutch-brake

pedal is depressed and the lift lever is in the disen- gaged position. In addition, the lift lever must be in the disengaged position when the unit is put into reverse or the engine will shut off. If the operator leaves the seat with the lift lever engaged and/or without setting the parking brake, the engine will shut off.

WARNING: Do not operate the lawn trac-

tor if the interlock system is malfunction-

Ing because it is a safety device, designed for protection.

WARNING: Look to the rear before back-ing up.

5. Release the parking brake by depressing the clutch-brake pedal, pressing outward on the speed control lever and moving to desired posi- tion. Use first speed position when operating the

lawn tractor lor the first time.

6. Releaseclutch-DraKepeclal810wlyto putunitinto

motion.

7. The lawn tractor is brought to a stop by depress- ing the clutch-brake pedal.

NOTE: When operating the unit initially, there will be

little difference between the highest two speeds until

after the belts have seated themselves into the pul-

leys during the break-in period.

Be sure that the lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower or engine. For best results and to insure more even grass distribution, do not mow when lawn is exces-

sively wet.

Page 10

WARNING:Beforeleavingthe operator's position for any reason, disengagethe blades, place the shift lever in neutral, engagethe parking brake, shut engine off andremovethe key.

When stopping the unit to empty a grass bag, etc., fol-

low the instructions above. This procedure will also

eliminate "browning" the grass, which is caused by

hot exhaust gases from a running engine. If unit stalls with speed control in high speed, or if

unit will not operate with speed control lever in a low

speed position, proceed as follows.

1. Place shift lever in NEUTRAL.

2. Restart engine.

3. Place speed control lever in high speed position.

4. Release clutch-brake pedal fully.

5. Depress clutch-brake pedal.

6. Place speed control lever in desired position.

7. Place shift lever in either FORWARD or REVERSE, and follow normal operating proce-

dures.

OPERATINGTHE CUTi'ING BLADES

The cutting blades may be engaged while the lawn tractor is moving or standing still. DO NOT engage the cutting blades abruptly as the sudden belt tension

on the pulley may cause the engine to stall.

WARNING: Keep feet and hands away from the discharge opening, the blades or any part of the deck. When the unit is used for other than mowing operations, the blade drive should be disengaged.

ADJUSTMENTS

SEAT ADJUSTMENT

The seat may be adjusted to different positions. Refer to seat installation section of assembly instructions.

DECKLEVELING ADJUSTMENT

If an uneven cut is obtained, the deck may be leveled by following instructions at end of assembly section.

CUTTING DECKENGAGEMENTADJUSTMENT

The cutting deck engagement may be adjusted to make certain deck is disengaged when lift lever is in the disengaged position, or to obtain more drive in the cutting positions. Correct adjustment as follows.

With the engine off, place the lift lever in the highest cutting position (first position). Remove the cotter pin and flat washer which secure the disengagement rod to the stabilizer shaft assembly. Shorten the rod by threading it in until the ferrule is against the back of the slot in the lift shaft assembly, and the rod lines up

with the hole in the stabilizer shaft. For more belt ten- sion the disengagement rod must be lengthened. To

decrease belt tension the disengagement rod must be shortened.

Check the adjustment by placing the lift lever in the disengaged position. The deck should move up and forward, allowing the belt to become loose. Start and test for disengagement. Repeat procedure as neces-

sary.

Stabilizer Shaft

Assembly

Disengagement Rod

Move the lift lever into the DISENGAGED position to raise the deck and disengage the blades.

GRASS COLLECTORAVAILABLE

GRASS COLLECTOR stock number 89-35111R is available as optional equipment for the lawn tractors shown in this manual.

,_ WARNING: The mower should not be

operated without the entire grass catcher or chute deflector in place.

NOTE: Under normal usage bag material is subject to

wear, and should be checked periodically. Be sure any replacement bag complies with the mower manu- facturer's recommendations. For replacement bags, use only factory authorized replacement bag.

Sprin!

FIGURE 12.

Stabilizer Plate

Flat Washer Hairpin Clip

SPEED CONTROL ADJUSTMENT (See figure 13)

NOTE: When operating the unit initially or after

replacing the belts, there will be little difference between the highest two speeds until after the belts have gone through a break-in period and have seated

themselves into the pulleys,

Page 11

If the full range of speeds cannot be obtained on your unit, adjust the speed control as follows.

1. Adjust the speed control lever by pushing the clutch-brake pedal forward until the stop on the

brake rod is against the frame. See figure t3. Have another person hold the pedal in this posi-

tion as you make the following adjustment. Place

the speed control lever in parking brake position. Remove the hairpin clip and flat washer, and adjust the ferrule on the rod so it is against the back end of the slot. See figure 13. Then length- en rod one more turn. Reassemble and secure

with theflat washer and hairpin clip.

2. Adjust the speed control link as follows to obtain the correct neutral adjustment.

A. Start the engine. B. Place the shift lever in Neutral position. C. Place the speed control lever in high speed

position.

D. Release the clutch-brake pedal completely, then

slowly depress the pedal all the way (to park

position). Hold the pedal in this position. E. Turn the engine off. F. After engine stops completely, release the

clutch-brake pedal. G. Place speed control lever in second position. H_ Remove the cotter pin and flat washer which

secures the speed control link to the variable

speed torque bracket assembly. I. Push the clutch-brake pedal backward by hand

as far as it will go using light pressure. Hold it in this position as you thread the speed control link

in or out of the ferrule until it lines up with the pin

on the variable speed torque bracket assembly.

J. Secure speed control link to variable speed

torque bracket assembly with flat washer and cotter pin.

Variable Speed

Torque Bracket

"_-._ Assembly

Speed Cotter Pin and

Control Flat Washer

Brake

Rod

Speed

Link

Ferrule

FIGURE 13.

Page 12

NEUTRAL ADJUSTMENT

1. Place the transmission in neutral. (The unit will move freely when pushed forward and backward

with the parking brake released.)

2. Loosen the bolt which secures the shift lever assembly to the shift lever link. See figure 14.

3. Place the shift lever in the neutral slot. See figure

14.

4. Tighten the bolt to 13 foot pounds.

Dimension "B" should be approximately 1/8" less than Dimension "A." See figure 16.

A.) To increase Dimension "B," screw tie rod into tie

rod end.

B.) To decrease Dimension "B," unscrew tie rod from

tie rod end.

C.) Reassemble tie rod. Check dimensions. Readjust

if necessary.

tral

Slot

Lever

Loosen

Bolt

FIGURE 14.

WHEEL ADJUSTMENT

The caster (forward slant of the king pin) and the camber (tilt of the wheels out at the top) require no adjustment. Automotive steering principles have been

used to determine the caster and camber on the trac-

tor. The front wheels should toe-in 1/8 inch. To adjust the toe-in, proceed as follows.

1. Remove the hex nut and lock washer, and drop

the tie rod end from the wheel bracket. See figure

15.

2. Loosen the hex jam nut on tie rod.

3. Adjust the tie rod assembly for correct toe-in.

Front

° 1

l_ (118" Less Than A)

FIGURE 16.

CARBURETORADJUSTMENT

WARNING: If any adjustments are made

to the engine while the engine is running

(e.g. carburetor), disengage all clutches and blades. Keep clear of all moving parts. Be careful of heated surfaces and

muffler.

Minor carburetor adjustment may be required to

compensate for differences in fuel, temperature, altitude and load. To adjust the carburetor, refer to

the separate engine manual packed with your unit.

NOTE: A dirty air cleaner wilt cause an engine to run rough. Be certain air cleaner is clean and attached to the carburetor before adjusting carburetor.

Rod Hex

Nut

Hex Nut

Lock Washer Tie Rod

End

FIGURE 15.

BRAKEADJUSTMENT (See figure 17)

NOTE: Your brake may be equipped with a lock nut

instead of the castle nut and cotter pin shown in figure

17.

The brake is located by the right rear wheel inside the frame. During normal operation of this machine, the brake is subject to wear and will require periodic examination and adjustment.

WARNING: Do not have the engine run-

ning when you adjust the brake.

Page 13

To adjustthebrake,removethe cotterpinfromthe

castlenut(ifsoequipped).Adjustthenutsothebrake startstoengagewhenthebrakeleveris1/4"to5/16"

awayfromtheaxlehousing.

Castle

Nut

TRANSAXLE

The transaxle is lubricated at the factory and does not

require checking. If disassembled for any reason, lubricate with 10 oz. of Shell grease, part number 737-0148.

WHEELS

The front wheels may be provided with grease fittings. The rear wheels must be removed from the axle for

lubrication. Lubricate both front and rear wheels at least once a season with automotive multi-purpose

grease.

PIVOT POINTS

Lubricate all pivot points with light oit at least once a season.

FIGURE 17.

LUBRICATION

,_ WARNING: Always stop engine and dis-

connect spark plug wires before clean- ing, lubricating or doing any kind of work on lawn tractor.

STEERING GEARS

Lubricate teeth of steering gears with automotive multi-purpose grease after every 25 hours of opera- tion or once a season. See figure 18.

STEERING SHAFT

Lubricate steering shaft at least once a season with

light oil.

FIGURE 18.

Steering Gears

MAINTENANCE

WARNING: Disconnect the spark plug wires and ground against the engine

before performing any repairs or mainte- nance.

TROUBLE SHOOTING

Refer to page 18 of this manual for trouble shooting informalion.

ENGINE

Refer to the separate engine manual for engine maintenance instructions.

Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and fol- low instructions carefully.

Service air cleaner every 10 hours under normal con- ditions. Clean every few hours under extremely dusty

conditions. To service the air cleaner, refer to the sep- arate engine manual packed with your unit.

The spark plugs should be cleaned and the gap

reset once a season. Spark plug replacement is rec- ommended at the start of each mowing season; check engine manual for correct plug type and gap specifi-

cations.

CLEANING ENGINE AND DECK

Any fuel or oil spilled on the machine should be wiped off promptly. Grass, leaves, and other dirt must not be

allowed to accumulate around the cooling fins of the engine or on any part of the machine.

Clean the underside of the deck after each mowing.

Page 14

CUTTING BLADES

A. Removal for Sharpening or Replacement

WARNING: Be sure to disconnect and

ground the spark plug wire and remove ignition key before working on the cutting blade to prevent accidental engine start- ing. Protect hands by using heavy gloves or a rag to grasp the cutting blades.

1. Remove the large bolt and lock washer which

holds the blade and adapter to the blade spindle.

2. Remove the blade and adapter from the spindle.

3. If the blade or blade adapter needs replacing, remove the two small bolts, lock washers and

nuts which hold the blade to the adapter.

B. Sharpening

Remove the cutting blades by following the directions

of the preceding section. When sharpening the blades, follow the original angle

of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grind- ing to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the mower and could break, causing personal injury.

The blade can be tested for balance by balancing it on a round shaft screwdriver. Remove metal from the

heavy side until it balances evenly,

NOTE: It is recommended that the blade always be removed from the adapter for the best test of balance.

C. Reassembly

Before reassembling the blade and the blade adapter to the unit, lubricate the spindle and the inner surface of the blade adapter with light oil. Lubricating the bolt holes, bolts and inner surface of the nuts with light oil is also recommended. A 4 oz. plastic bottle of light oil lubricant is available. Order part number 737-0170. Engine oil may also be used. When replacing blades, be sure to install the blade with the side of the blade marked "Bottom" (or with part number) facing the ground when the mower is in the operating position.

Blade Mounting Torque

Center Bolt: 450 in. Ibs. rain., 600 in. Ibs.'max. Blade Adapter Bolts: 200 in. Ibs. rain., 350 in. Ibs. max.

To insure safe operation of your unit, all nuts and bolts

must be checked periodically for correct tightness.

FUEL FILTER

Your unit is equipped with a replaceable in-line fuel fil- ter. Replace filter whenever contamination or discol- oration is noticed. Order replacement filter through your engine authorized service dealer.

DRIVE BELTREMOVAL AND REPLACEMENT

WARNING: Disconnect the spark plug

wire and ground it against the engine. Block the wheels of the unit,

NOTE: Figures 19, 22 and 23 are shown with the unit

tipped up for clarity. It is not necessary to tip the unit to remove the belts.

However, ff tipping the unit is desired, remove the bat- tery from the unit. To prevent gasoline leakage, drain

the gasoline, or remove the fuel tank cap, place a thin

piece of plastic over the neck of the fuel tank and screw on the cap. Be certain to remove the plastic

when finished changing the belts. Block unit securely.

DECK BELT

1. Place the lift lever in the disengaged position.

2. Remove the hex bolts (belt keepers) and cupped washers from the engine pulley belt guard. See figure 19.

NOTE: When reassembling, make certain hex and

cupped washers are assembled in the same locations from which they were removed. See figure 19.

Cupped Hex Bolts Cupped Washer

FIGURE 19.

Unhook the deck belt from the engine pulley. Place the lift lever in the engaged (all the way for-

ward) position.

Disconnect the spring which is attached to a bracket on the transaxle, inside the left rear wheel. Use a spring puller or other suitable tool.

Disconnect the six deck links by removing the hairpin clips and flat washers.

Disconnect the stabilizer plate from the stabilizer

shaft assembly by removing the hairpin clips and flat washers and sliding out the rod. Refer to fig-

ure 12.

8. Place the lift lever in the disengaged position.

Page 15

9. Slide the deck from beneath the lawn tractor.

10. Remove the belt guards at each deck pulley by removing the self-tapping screws. See figure 20.

Self-Tapping

Screws

Stabilizer

Plate Belt

Guard

5. Remove the two bolts which hold the shift lever bracket to the frame on the left side of the unit.

Swing the bracket toward the right so the belt can be removed from the transmission pulley. See fig- ure 22.

6. Replace belt, and reassemble in reverse order.

7. Adjust the speed control as instructed in adjust- ment section.

Transmission

Pulley

Shift Lever Bracket

Hex Bolt

Belt Guard

FIGURE 20.

11. Remove and replace the belt, reassemble follow- ing the instructions in reverse order.

REAR DRIVE BELT

1. Place shift lever in neutral position. Unscrew the

shift knob. Remove the two truss head screws which secure the transmission cover. See figure 21A.

2. Lift the transmission cover. Unplug the safety wire from beneath the transmission cover. See figure

21B. Remove transmission cover.

Wire

Idler

Pulley

Variable.

Speed Pulley

Rear

Drive

Belt

FIGURE 22.

FRONT DRIVE BELT

1. To remove the front drive belt, first remove the rear drive belt from the idler pulley and variable speed pulley.

2, Place the lift lever in the disengaged position.

3. Remove the hex bolts (belt keepers) arid cupped washers from the engine pulley belt guard. Refer to figure 19.

NOTE: Make certain hex bolts are reassembled as

shown in figure 19.

4. Unhook the deck belt from the engine pulley. 5, Remove the two self-tapping screws on each side

of the frame which hold the engine pulley belt guard to the frame. See figure 23. Remove the engine pulley belt guard by slipping it forward and

down.

FIGURE 21.

Self-

Tapping (

Screws

Self -

;,Tapping

Screws

3. Push the idler pulley toward the right side of the unit. Lift the belt over the idler pulley. See figure

22.

4. Remove the belt from the variable speed pulley.

FIGURE 23.

Engine Pulley

Belt Guard

Page 16

6. Place the clutch-brake pedal in park position.

7. Push forward on the variable speed pulley, and lift the belt off the engine and remove the belt from the engine pulley.

8. Release the clutch-brake pedal. Using the pedal to move the variable speed pulley as necessary, lift the belt up and off the variable speed pulley.

NOTE: When reassembling, make certain belt is

inside the pins. See figure 24.

Variable

Speed Pulle

FIGURE 24.

9. Reassemble with a new belt, following instruc- tions in reverse order.

10. Adjust the speed control as instructed in adjust- ment section.

BATTERYREMOVAL OR INSTALLATION

WARNING: When removing the battery, follow this order of disassembly to pre- vent the screwdriver from shorting against the frame.

1. Remove the Negative cable.

2. Remove the Positive cable.

To install a battery:

1, Attach the Positive cable.

2. Attach the Negative cable.

JUMP STARTING

1. Attach the first jumper cable from the Positive ter- minal of the good battery to the Positive terminal of the dead battery.

2. Attach the second jumper cable from the Negative terminal of the good battery to the

FRAME OF THE UNIT WITH THE DEAD BAT-

TERY.

WARNING: Failure to use this starting

procedure could cause sparking, and the gas in either battery could explode.

BATTERYMAINTENANCE

1. Check periodically (every two weeks or before and after charging) to be sure electrolyte level is above the lowest line on battery. Add only dis- tilled water or a good quality drinking water.

NEVER add additional acid or other chemicals to

battery after initial activation.

2. The battery should be checked with a hydrometer after every 25 hours of operation. If the specific gravity is less than 1.225, remove battery and

recharge.

3. Coat the terminals and exposed wiring with a thin coat of grease or petroleum jelly for longer ser- vice and protection against electrolyte corrosion.

4. The battery should be kept clean, Any deposits of acid should be neutralized with soda and water.

Be careful not to get this solution in the cells.

BATTERYSTORAGE

1. Charge battery using normal methods. NEVER store discharged battery as it will not recover.

2. When storing battery for extended periods, dis- connect battery cables. Removing battery from

unit is recommended.

3. Store in cold, dry place.

4. Recharge battery whenever the specific gravity is

less than 1.225, before returning to service, or every two months, whichever occurs first.

COMMON CAUSES FOR BATTERY FAILURE ARE:

1. Overcharging

2. Undercharging

3. Lack of water

4. Loose holds downs and/or corroded connections

5. Excessive loads

6. Battery electrolyte substitutes

7_ Freezing of electrolyte

NOTE: THESE FAILURES DO NOT CONSTITUTE

WARRANTY.

Page 17

TIRES

Recommended operating tire pressure is approxi- mately 12 p.s.i. (check sidewall of tire for tire manu- facturer's recommended pressure). Maximum tire pressure under any circumstances is 30 p,s.i. Equal tire pressure should be maintained on all tires.

When installing a tire to the rim, be certain rim is clean and free of rust. Lubricate both the tire and rim

generously. Never inflate to over 30 p.s.i, to seat beads.

4. Refer to battery storage instructions on page 16.

5. Store unit in a clean, dry area. Do not store next to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in

an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or sificone, coat the equipment, especially any chains, springs, bearings and cables.

WARNING: Excessive pressure (over 30 p.s.i.) when seating beads may cause

tire/rim assembly to burst with force suf- ficient to cause serious injury.

OFF-SEASON STORAGE

If the machine is to be inoperative for a period longer

than 30 days, prepare for storage as follows.

1. Clean the engine and the entire unit thoroughly.

2. Lubricate all lubrication points, Wipe the entire machine with an oiled rag to protect the surfaces.

3. Refer to the engine manual for correct engine storage instructions. The engine must be com- pletely drained ef fuel to prevent gum deposits

from forming on essential carburetor parts, fuel

lines and fuel tanks.

OPTIONAL EQUIPMENT

At the time of manufacture of lawn tractor, the option- al accessories listed below are available.

Description

36;' Snow Thrower 42" Snow Blade

Grass Collector 42" Mulching Kit

30 Lb. Wheel Weights

Stock No. 80-3384806

80-3387908

80-3511103 80-3520109 80-3386204

Page 18

TROUBLE SHOOTING GUIDE

TROUBLE LOOK FOR REMEDY

Engine will not Battery installed incor- The battery must be installed with the negative terminal, identified at the terminal post by (Neg, N or

crank rectly -), groundecL The positive terminal (Pos. P or +) attaches to the large cable from the solenoid. The

small red wire from the fuse holder or circuit breaker is also attached to the positive terminal.

Engine cranks

,butwill not start

Blown fuse or circuit breaker

Battery is dead or weak

Mechanical failure (Wires and switches)

Throttle or choke not in

starting position

No spark to spark plug

Replace fuse with 7-1Y2 amp. automotive type fuse. Fuses seldom fail without a reason. The problem

musl be corrected Check for loose connections in the fuse holder. Replace fuse holder if necessary. A dead short may be in the cranking or charging circuit where the insulation may have rubbed through and exposed the bare wire. Replace the wire or repair with electrician's tape if the wire strands have not been damaged.

Note: Look for a wire pinched between body panels, burned by the exhaust pipe or muffler or rubbed against a moving part

Use a hydromete_ to check the condition of the battery. The Specific Gravity (s.g.) should be 1 265 at 80°F. (1.215 s.g. minimum needed for cranking engine). The reason for the battery failing must be determined. (1)Defective battery. Battery will not accept or hold a full charge. (2) Short circuit. Check for grounded wire. (3) Charging system not working.

The charging system is an alternator located under the flywheel. It is unregulated and rated 3 amp. at 3600 r.p,m. A diode {rectifier) is located in the output lead just before the wire harness plug on the engine side

To Alternator (_ _- -

Shrink 3 AMP DC

Wire Diode Tube (Bart.)

._ /'7 AMP AC

pL=__ _==" :-J_'-_ Lf (Lamps)

• - "--5 -- -,

rBlack

Wire Polarized

Plug

The diode changes A.C, to D.C. to charge the battery. A bad diode can either fail to charge the battery

or discharge the battery if the alternator is shorted as well as the diode To test: (1) Disconnect charger

lead from the battery (small red wire) (2) Connect 12 V small test lamp between the 3 amp. D.C.

charge lead and the positive terminal of the battery. (3) With the engine off, the lamp should not light. If

it does, the diode and possibly the alternator should be replaced. (4) Start the engine The lamp should

light. It it does not, the alternator (stalor) or lead wire is bad and shouid be replaced.

The interlock system includes two mechanical activated switches which are wired in series in the

circuit used to energize the starter solenoid. While testing the interlock system, you will make the

mower temporarily unsafe by permitting the engine to be started with the blade and clutch engaged.

WARNING: While testing, disengage the clutch, shut off the blade control, set the parking brake and

place the gear shift lever in neutral. Attach a wire (minimum 18 gauge) to the positive terminal of the battery and touch the other end to the small terminal on the solenoid. If the engine does not crank: (1) There is a loose connection or poor ground. (2) The solenoid may be bad. The solenoid can be checked by using a heavy wire (#8 gauge minimum) and jumping between the two large terminals, tf the engine cranks, the solenoid is bad. (3) If the engine does not crank when you jump the solenoid, have the starler motor tested by an authorized engine dealer. If the engine does crank, the problem is wilh one of the safety switches, ignition switch or the wire between the fuse holder {or circuit breaker) and the small terminal on the solenoid. Note: Look for a poor connection at the switches or a defective switch. Replace if necessary.

Check owner's guide for correct position for throttle control and choke for starting.

Spark plug lead disconnected. Connect lead. Hold spark plug lead away from engine block about 1/8". Crank engine There should be a spark If not, have engine repaired at authorized engine service

dealer.

Faulty spark plug. To test, remove spark plug. Attach spark plug lead to spark plug. Ground the spark plug body against the engine block. Crank the engine. The spark plug should fire at the electrode.

Replace if it does not.

Page 19

TROUBLE SHOOTING GUIDE (Continued)

TROUBLE LOOK FOR REMEDY

No fuel to the carburetor Gasoline tank empty. Fill

Fuel line or in-line fuel filter plugged. Remove and clean fuet line. Replace filter if necessary.

Air filter dirty If the air cleaner is dirty, the engine may not start. Clean or replace as recommended by the engine

manulacturer.

Engine smokes Engine loses crankcase Dipstick not seated or broken. Replace defective part.

vacuum Engine breather defective. Replace.

Excessive Bent or damaged blade Stop engine immediately. Check all pulleys, blade adapters, keys and bolts for tightness and vibration spindle damage. Tighten or replace any damaged parts.

Bent blade Stop engine immediately. Replace damaged blade. Only use obginal equipment blades.

Mower will not Engine speed low Throttle must be set at full throttle 0ischarge Transmission selection Use lower transmission speed. The slower your ground speed, tr_e better the quality ot cut. grass or leaves Blades short or dull Sharpen or replace blades (uncut strip problem only). uncut strips

Page 20

TMO-3100002

TMO 3395309 "

REF.

NO.

2 3 4 5

7 8

10 11 12

14 15 16

17 18 19 20

21 22 23 24

PART

NO.

17551A

738-0724 736-0342

_710-0258

736-0329

712-0287 749-0812

731-1099A

712-0380

731-1097A

736-0119

712-0267

725-0963

725-1649 710-0703 710-0599

736-0173 726-0233 712-0185 710-0118

17632 731-1096A 725-0267 725-0201 746-0614A

16 AND 18 H.P. 42" LAWN TRACTORS

PARTS LIST FOR MODELS TMO-3100002 AND TMO-3395309

DESCRIPTION

Hood Shld. Bolt .375" Dia. x .125" Lg.

Fl-Wash. ,28" I.D. x .75" O.D. Hex Bolt I/4-20 x .62" Lg.*

L-Wash. I/4" I.D.* Hex Nut I/4-20 Thd.*

Grille Support Rod Headlight Lens Flange L-Nut 114-28 Thd.

Grille L-Wash. 5/I 6" I.D.* Hex Nut 5/16-18 Thd.*

Lamp

Socket

Carriage Bolt I14-20 x .75" Lg. Hex Wash. Hd. TT-Tap Scr.

114-20 x .5" Lg.

Fl-Wash..281" I.D. x .73" O.D. Bolt Retainer 114" I.D.

Speed Nut I/4-20 Thd.

Hex Bolt 5/16-18 x ,75" Lg. Gas Tank Support Brkt.

Dash Ignition Switch

Ignition Key

Choke Control

iREF. PART

NO. _ NO.

i I

26 725-0634 27 725-0925 28 15821 29 15822 30 710-0607

32 33

35 38

40 41 42

I 44

46 47

710-0286

710-0167

17324A

17871

710-0726

17286A

831-0823A 710-0779A

746-0634 777-9206 710-0603

17782 710-0642

DESCRIPTION

Light Switch

Ammeter Grille Mtg. Brkt.--L.H.

Grille Mtg. Brkt.--R.H. Hex Wash. Hd. Tap Scr, 5/16 x

.5" Lg.

Truss Mach. Scr. 1/4-20 x .5" Lg.

(TMO-3395309)

Carriage Bolt 1/4-20 x .62"

(TMO-3100002)

Fender (TMO-3100002) Fender (TMO-3395309)

Hex Wash, Hd AB-Tap Scr.

5/16 x .75" Lg.

Shift Cover

Throttle Box Ass'y. Truss Mach. AB-Tap Scr.

#10 x .5" Lg.

Throttle Control Wire Grille Reflector Label

Hex Wash. Hd. B-Tap Scr.

5/16-18 x .5" Lg.

Choke Retainer

Hex TT-Tap Scr. 1/4-20 x .75"

Lg.

i i

Page 21

6 3Z

26 _

30 51

TMO-3100002 TMO-3395309

413

REF,

NO.

3 4

6 7 8

9 10 11 12 13 14

21 22

23 24 25 26

28 29 30 32

34 35

PART

NO.

736-0159 710-1208

738-0155 738-0145 736-0141

15607D 751-3071 751-0555 726-0209 751-0535-26 726-0205 712-0138 712-0287 736-0329 732-0672 738-0526 710-0227

726-0139

17621 710-0623

710-0726

7!0-0134 17770 761-0168A 731-0909 731-0910 710-0323

17620C

736-0169 726-0278

16 AND 18 H.P. 42" LAWN TRACTORS

PARTS LIST FOR MODELS TMO-3100002 AND TMO-3395309

DESCRIPTION

FI-Wash. 344" I.D. x .875" Hex Wash. Hd. Tap Scr.

5/16-18 x 3.25" Lg.

Shld. Bolt .437" Dia. x •162" Shld. Bolt .50" Dia. x .84"

Spr-Wash..445" ID. x .75 Seat Pivot Bracket

Fuel Cap Fuel Tank

Tie Strap

Fuel Line Hose Clamp

Hex Nut 1/4-28 Thd. Hex Nut 1/4-20 Thd." L-Wash. 1/4" I.D.

Compression Spring Running Board Rod

Hex Wash. Hd. AB-Tap Scr.

#8 x .50" Lg. Speed Nut #10Z Front Pivot Brkt.

Hex Tap Scr. 3/8-16 x .75" Hex Wash• Hal. AB-Tap Scr.

5/16 x .75" Lg. Carriage Bolt 1/4-20 x .62"* Running Board (R.H & L.H.)

, Blade Brake Ass'y. : Rubber Foot Pad--L.H.

Rubber Foot Pad--R.H.

i Truss Mach. Scr. 5/16-18 x i .75" Lg*

Lower Frame L-Wash. 3/8" I.D.* Insulator Boss Plate

REF, PART

NO. NO.

37 i 736-0463 38i 710-0118

39i 17622B 41i 712-0798

42! 732-0581B 43! 731-1200 44! 725-1430

45 46 47; 48

50 51 52

53 54

55 56_

57_

58 E,

63 65

67 68 i

69i

17623

17286A 725-0759 726-0279

17951

17953 712-0267 736-0119

17239A 757-0338 757-0360 17960

738-0296

725-1303 722-0160 710-0650

726-0320 725-1439

17952

710-0351

748-0347 710-1221

710-0412

i DESCRIPTION

FI-Wash..25" I.D. x .625" O.D. Hex Bolt 5/16-18 x .75" Lg.*

Upper Frame--R.H. Hex Nut 3/8-16 Thd.*

Extension Spring 5.31" Lg. Battery Cover

12-V Battery (275 Cold Crank

Amps)

Upper Frame--L.H. Shift Cover

Reverse Safety Switch Insulator Plate

Seat Pivot Brkt. Support--L.H. Hitch Plate

Hex Nut 5/16-18 Thd.* L-Wash 5/16" I.D.* Seat Lift Brkt.

Seat (TMO-3395309) Seat (TMO-3100002) Seat Pivot Brkt. Support--R.H. Shld. Bolt .437" Dia. x .268"

Spring Switch Bushing Hex Wash. TT-Tap Scr. 5/16-18

x 7/8" Lg.

Insulator Nut Plate Safety Switch (Seat)

Battery Tray

Truss Mach. B-Tap Scr.

#10 x .5" Lg.

Spring Spacer Pan Hd. Cutting Scr. 5/16-18 x

.75" Lg.

Hex Bolt 1/4-28 x .75" Lg.

Page 22

TMO-3100002 TMO-3395309

To Engine. //7

1. 7 /'

Page 23

[

TMO-3100002

TMO-3395309

REF.

NO,

4 5

9 0

__2 t3

__4

._7 ._ __c

PART

NO.

731-0220 712-0237 736-0242 731-0806A 731-0954 737-0280

17198A

738-0141

710-0152

!750-0535

736-0169

710-0726 711-0788

17621

738-0527

7!2-0798 736-0169 712-0237

16481A

710-0772

741-0487A 683-0002

17585 712-0241 736-0169 723-3018 747-0753

16 AND 18 H.P, 42" LAWN TRACTORS

PARTS LIST FOR MODELS TMO-3100002 AND TMO-3395309

DESCRIPTION

Steering Wheel Cap

Hex L-Nut 5/16-24 Thd. Belleville Wash..345" I.D.

Steering Wheel Steering Bellow Grease Fitting

Retainer Plate Shoulder Bolt .437" Dia. x

.35 Lg. 5/16-18 Thd.

Hex Bolt 3/8-24 x 1.0" Lg.

(Grade 5)

Spacer .380" I.D. x .625"

O.D. x .227

L-Wash. 3/8" I.D.* Hex Wash. Hd. Self-Tap Scr.

Steering Drag Link Front Pivot Brkt.

Shoulder Bolt .498" Dia. x

2.04 Lg. 3/8-16 Thd.

Hex Nut 3/8-16 Thd.* L-Wash. 3/8" I.D.*

Hex Cent. L-Nut 5/16-24 Thd

Steering Arm Front Axle

Hex Bolt 5/16-24 x 200"

Lg. (Grade 5) Hex Ftg. Brg .632 I.D. Pivot Bar Ass'y. Front Axle Ass'y.--LH. Hex Nut 3/8-24 Thd.*

L-Wash. 3/8" I,D.* Ball Joint 3/8-24 Thd.

Tie Rod

*Common Hardware--May be purchased locally.

IMPORTANT: DO NOT order parts by reference number (Ref. No.),

REF.

NO.

31 32 33

34 35 36 37 38 39 40 42 43 44 45 46 47 48 49

50 51 52

54 58 59

i 60

PART

NO.

712-0711

17584 634-0056 734-0864 634-0024 741-0487A

736-0285

731-0484A 714-0470

736-0187

726-0214

712-0446

710-0538

736-0119

736-0343

750-0532

7t2-0214

736-0169

712-0158

736-0119

717-0622A

741-0225

736-0187

738-0743

736-0271

736-0187

723-3018 736-0607

]

DESCRIPTION

Hex Jam Nut 3/8-24 Thd.* Front Axle Ass'y,--R.H,

Wheel Ass'y. Comp. Tire Only

Front Wheel Rim Only Bearing

FI-Wash..635 I.D. x 1.59" O.D. Front Wheel Hub Cap

Cotter Pin 1/8" Dia. x 1.25"* FI-Wash, .640" I.D. x 1.24" O.D.

Push Cap 5/8" Dia. Rod Hex Jam Nut 3/8-24 Thd. Hex L-Bolt 5/16-18 x .62"* L-Wash. 5/16" I.D.* FI-Wash..33" I.D. x 1.25" O.D.

Spacer (Plastic) Hex Cent. L-Nut 3/8-24 Thd, L-Wash. 3/8" I.D.* Hex Cent. L-Nut 5/16-18 Thd.

L-Wash. 5/16" I.D.*

Steering Gear Segment

Hex Fig. Brg..634 I.D. FI-Wash. (Hardened) Steering Shaft

Wave-Wash..32" I.D. x .62" O.D

FI-Wash. (Hardened) Drag Link Ball Joint 3/8-24 Thd.

Ext. L-Wash. 5/16" I.D.

64 736-0356 Bell-Wash..39" I.D, x 1.38" O.D. 66 710-0459 Hex Bolt 3/8-24 x 1.5" Lg. (Gr. 5) 67 734-0255 Air Valve l

68 737-0211 Grease Fitting j

NOTE: Specifications subject to change without notice or obligation,

TMO-3100002 TMO-3395309

PARTS LIST FOR LAWN TRACTORS

REF. PART

DESCRIPTION

NO. NO.

1 710-0924

2 16194

3 720-0218

4 16192

5 736-0192 6 711-0198 7 738-0155 8 747-0503A

9 714-0111 10 736-0226 11 736-0119 12 712-0267 14 732-0303 17 736-0140 19 736-0329

20 712-0287

Truss Mach. Scr. 1/4-20 x

.75" Lg.

7-Speed Selector Plate

Shift Knob Speed Selector Lever Ass'y.

Flat Washer .53" I.D. x .93" Ferrule 3/8-24 x .37" Dia. Shoulder Bolt

Speed Control Link Cotter Pin 3/32" Dia. x 1.0"*

FI-Wash..469" I.D. x .88" L-Wash. 5/16" I.D.* Hex Nut 5/16-18 Thd.*

Spring .38" O.D. x 3.18" Lg. FI-Wash..385" I.D. x .62" L-Wash. 1/4" I.D.* Hex Nut 1/4-20 Thd.*

Page 24

TMO-3100002 TMO-3395309

89',

/02

B 3-

TOEN61NE

IMPORTANT: Use only Original

Equipment Manufacturer (O.E.M.) V-belts when replacing belts. They are of special construction

(type of cord, cord location, length, etc.). Use of V-belts other than O.E.M. belts generally will provide only temporary service. For best results, use only factory approved parts.

56 Note: If brand of tire is impor-

tant, order by part number and description (description is printed on the sidewall of tire) [i.e. Armstrong Super Turf, Goodyear Softrac, Carlisle Turf Saver, etc.].

\ 128

4_ I09

Page 25

TMO-3100002

TMO-3395309

16 AND 18 H.P. 42" LAWN TRACTORS

PARTS LIST FOR MODELS TMOo3100002 AND TMO-3395309

REF. PART

NO. NO. DESCRIPTION

2 3 5

14 15 16

17 18

19 20 21 22 23 24

29 30 31

33 34 35 36 39

40 41

17840

17962 736-0119 710-0502A

17620C 712-0287 736-0329 710-0604 17358C 736-0242 712-0267 710-0190 714-0114 756-0424 736-0322 736-0171 710-0757

754-0280 710-0118

17963

741-0591

712-0241

17643

736-0169 712-0241

17629A

732-0556

i714-0149B

750-0802 712-0138 710-0776

i711-0747

Transaxle Mtg, Brkt. Switch Plate

L-Wash. 5/16" I.D.* Hex L-Wash. Tap Scr. 3/8-16 x

1.5" Lg. Lower Frame Ass'y. Hex Nut 1/4-20 Thd.* L-Wash, 1/4" I.D.*

Hex TT-Tap Scr. 5/16-18 x .62" Belt Guard Brkt. Ass'y. Bell-Wash..345" I.D. x .88" Hex Nut 5/16-18 Thd.*

Hex Bolt 5/16-18 x 4.0"* Sq. Key 1/4" x 1/4" x 2.00"

Engine Pulley FI-Wash. 7/16" I.D. x 1.25" L-Wash. 7/16" I.D.*

Hex Bolt 7/16-20 x 1.50" Lg.

Variable-Speed Belt

Hex Bolt 5/16-18 x .75" Lg.

Bearing Shaft Bracket Ass'y.

Flanged Nyliner Brg. 5/8"

I.D. x .88" Lg.

Hex Nut 3/8-24 Thd.* Idler Bracket

L-Wash. 3/8" I.D.* Hex Nut 3/8-24 Thd.*

Transaxle Support Brkt.

Ext. Spring 94" O.D, x 7_58" Inter. Cotter Pin

Spacer 63" I.D. Hex Nut 1/4-28 Thd.

Hex AB-Tap Scr. 1/4" x .62" Lg, Belt Guard Pin

42 !736-0222 43 710-0599

44 17715A 45 j736-0117

46 1710-0351 47 17686A

48 i735-0196 51 17705 53 732-0264 54 732-0413 55 710-0176 56 734-1675

734-1596 57 734-0603A 58 734-0255 59 710-0627 6! 732-0454 63 736-0275 64 710-0428

Ext. L-Wash. 1/4" I.D. Hex Wash. Hd. S-Tap Scr.

1/4-20 x .50" Lg.

Clutch/Brake Pedal Ass'y. FI-Wash

Truss Mach. Scr. B-Tap Scr.

#10 x .5" Lg.

Brake Rod Ass'y. Foot Pad

Shift Lever Ass'y. Ext. Spring .38" O.D, x 2.5" Ext. Spring .59" O.D, x 7.08" Hex Bolt 5/16-18 x 2.75"*

Wheel Ass'y. Comp.

Tire Only

Wheel Rim Only

Air Valve (Service Only)

Hex Bolt 5/16-24 x .75" Lg.* Brake Return Spring Anchor

FI-Wash..34" I.D. x .68" O.D.

Hex Bolt 1/4-28 x 1.25" Lg.*

REF.

NO.

65 66 67

68 69 701 711 72 731

75 76 77 78 79 80 81 82

84 85

88 89 9O 92 93 94 97 98

99 100 101 102

107 108

109 111 112 113 115 116 119 120 121 122 128

129

PART

NO.

732-0568 732-0384

16554A

741-0419 714-0111

748-0234 747-0530A 741-0405 720-0232 756-0437 656-0004 736-0427 712-3035 710-0539 754-0370 716-0114 736-0355 717-0800A

16354B 732-0525

17668 17669

725-1426

17630 736-0414 710-1223 725-3169A 738-0755 736-0105 738-0569 736-0331 736-0256 714-0470 710-0604

17860 714-0470 711-0198 710-0195 736-0270

17707 736-0140 741-0404

710-0427 756-0217 736-0280 712-0798 710-0650

710-0726

DESCRIP_ON

Ext. Spring Ext. Spring .62" O.D. x 6.12"

Variable Speed Torque

Brkt. Ass'y.

Flanged Bearing

Cotter Pin 3/32" Dia.* Shoulder Spacer .27" Lg.

Speed Control Link Truss Bearing .56 Dia. x 1.25" Shift Knob

Fl-ldler Pulley 3.25" x .75" "V" Pulley Bell-Wash..56" I.D. x 1.125"

Hex Jam Nut 5/16-18 Thd.

Hex Bolt 3/8-24 x 1.75" Lg. Variable Speed Belt Snap Ring .56" Dia. FI-Wash.

Variable Speed Pulley

Ass'y. 5" O.D.

Variable Speed Brkt. Ass'y. Comp. Spring--Clip Axle Support Brkt.--R.H. Axle Support Brkt.--L.H.

(Not Shown)

Solenoid Shift Lever Bracket

Teflon Washer .565" I.D.

Hex Bolt 1/4-20 x 3.5" Lg. Safety Switch. (Clutch)

Shld. Bolt 3/8-24 x 3.12" Lg. Bell-Wash..38" I.D. x .88"

Shaft .56" Dia. x 3.875" Lg. Bell-Wash..39" I.D. x 1.12" FI-Wash..64" I.D. x .94"

Cotter Pin 1/8" Dia. x 1.25"

Hex Wash. Hd. Scr. 5/16-18

x .62" Lg.

Pedal Bracket

Cotter Pin 1/8" Dia. x 1.25"

Ferrule Hex Bolt 1/4-28 x .50" Lg.

Bell-Wash..265" I.D, x .75" Shift Lever Link Ass'y.

FI-Wash..385" I.D. x .62" Needle Brgs. (2 Req'd.) Hex Bolt 3/8-16 x 1.25" Lg.

Fl-ldler w/Flanges 2.75" O.D. FI-Wash..39" I.D. x 1.12" O.D. Hex Nut 3/8-16 Thd.

Hex Wash. TT-Tap Scr. 5/16-18

x .75" Lg.

Hex Wash. AB-Tap Scr. 5/16-18

x .75" Lg.

Page 26

TMO-3100002 TMO-3395309

16 AND 18 H.P. 42" LAWN TRACTORS

PARTS LIST FOR MODELS TMO-3100002 AND TMO-3395309

REF.

NO.

4 5 6 7 8

12 13 14

15 t6

17 18

PART

NO.

09735A 17640 17641 17710 !4800A 14804A 748-0331 736-0264 736-0119 712-0267

714-0470 736-0256 732-0412A

08540

710-0604

748-0176 710-1238

DESCRIPTION

19 710-0118

20 17730 21 17622B 23 736-0267 24 736-0160

*Common Ha_ware---May be purchased locally.

IMPORTANT: DO NOT order pa_s by reference number (Ref. No.).

Connecting Rod Pivot Link Ass'y.--L.H. Pivot Link Ass'y.--R.H. Deck Hanger Link Ass'y. Deck Hanger Link Ass'y. Deck Hanger Link Ass'y, Shld. Spacer .318" I.D.

FI-Wash..344" I.D. x .62" O.D. L-Wash, 5/16" I.D.* Hex Nut 5/16-18 Thd.* Cotter Pin 1/8" Dia. FI-Wash..635" ID. x 1.0" O.D.

Deck Lift--Down Stop (Incl.

Ref. 15)

Knob Hex Wash. Tr-Tap Scr.

5/16-18 x .75" Lg.

Flange Brg..63" I.D.'l" Hex Wash. Hd. Scr. 5/16-18

x .875" Lg.

Hex Bolt 5/16-18 x .75" Lg. Index Brkt.

Upper Frame--R.H, FI-Wash..385" I.D. x .87" O,D. FI-Wash. ,531" I.D, x .93" O.D.

REF. PART

NO. NO.

25 728-0272 26 738-0526 27 710-3007

28 14802A 29 711-0723A 30 17712 31 712-3066 32 711-0841

33 17637A 34 725-0803C 35 714-0145 36 732-0637 37 17636A 38 738-0670 39 732-0638

40 720-0233

41 17675

42 738-0669 43 747-0598 44 17624

45i 732-0556

46i 17623 47i 741-0313 48i 17128

DESCRIPTION

Clamp Running Board Rod Hex Wash, Hal. Tap Scr. Link Deck Lift Ass'y. Adj. Ferrule 3/8-24 Thd, Adj. Deck Lift Link Hex Nut 1/2-20 Thd. (Gr. 5) Lift Link Adjuster Lift Shaft Ass'y. Safety Switch (Deck) Inter. Cotter Pin 3/8" Dia.

Extension Spring Stabilizer Bracket

Shaft 112" Dia. x 10.28" Lg. Extension Spring Grip (Lift Handle) Deck Lift Handle Ass'y. Shaft 3/8" Dia. x 9.34" Lg. Disengagement Rod Stabilizer Shaft Ass'y. Extension Spring 7.58" Lg. Upper Frame--L. H,

Flange Brg, .632" I.D. Spring Retainer Brkt.

i , I

Page 27

TMO-3100002 TMO-3395309

REF. PART

NO. NO.

3 17600A

813-06119

4 17664 6 710-0152 7 710-0599

8 710-0258

9 710-0888 10 711-0792 11 712-0123 13 712-0181 14 712-0287 17 734-0973 18 736-0105

19 736-0119

20 736-0217

22 i738-0373 23 742-0499A 25 748-0300

9 23 20_t

20"- . 6II**

16 AND 18 H.P. 42" LAWN TRACTORS

PARTS LIST FOR MODELS TMO-3100002 AND TMO-3395309

DESCRIPTION

REF. NO,

42" Deck Ass'y. 26 42" Deck Ass'y. Comp. 27

(For Service Only) 28 Belt Guard Deck 33 Hex Bolt 3/8-24 x 1.0" Lg. 35

Hex Wash. Hd. TT-Tap Scr. 37

1/4-20 x .5" Lg, 39 Hex Bolt 1/4-20 x .62" 42

Hex Bolt Special 5/1,6-24 x 1.0" 52 Hinge Pin 53 Hex Nut 5/16-24 Thd.* 54 Hex Top L-Nut 3/8-16 Thd. 55 Hex Nut 1/4-20 Thd.* Deck Wheel--5" 56 Bell-Wash..40" I.D. x .88" 57

OD. 58

L-Wash. 5/16" I.D.* 59

L-Wash. 3/8" I.D.--H.D. 60 Shld. Bolt .498" Dia. x 1.53" 61

High-Lift Blade 62 Blade Adapter

PART

NO.

754-0371A 736-0270 09322

710-0157 712-0318 736-0158 717-0906 756-0556 703-1693 732-0602 726-0106 731-1032

710-0157 17493A 736-0242 710-0167 17861A 17961

712 0271

DESCRIPTION

V-Belt Bell-Wash. 1/4" I.D. Brake Disc

Hex Bolt 5/16-24 x .75" Lg Hex Jam Nut 5/8-18 Thd.

L-Wash. 5/8" I.D.* Blade Spindle Ass'y. Comp.

5.5" Dia. Pulley Hinge Mtg. Brkt.

Torsion Spring

Push Nut

Chute Ass'y. Comp. (Incl. Ref.

10, 52, 53, 54, 55)

Hex Bolt 5/16-24 x .75" Lg.

Deck Hanger Channel

Bell-Wash_ .345" I.D. x .88" Carr. Bolt 1/4-20 x ,5" Lg.

Deck Skirt Ext.--Long Deck Skirt Exl.--Short

Hex Seres Nut 1/4-20 Thd.

*Common Hardware---May be purchased locally.

IMPORTANT: DO NOT order parts by reference number (Ref. No.).

Page 28

TMO-3100002 TMO-3395309

1-/8

SINGLE SPEED TRANSAXLEmR.H. MODEL 618-0073

Page 29

REF.

NO.

1 2 3

12 13 14

15 16 17

9 20 21

22 23

24 25 26

27 28 29 32

TM0-3100002

TMO-3395309

PARTS LIST FOR

SINGLE SPEED TRANSAXLE RIGHT HAND 618-0073

PART

NO, DESCRIPTION

732-0614 716-0171 710-1026

710-0809 719-0314 711-0861

736-0335 717-0633

716-0171 711-0943 741-0336

717-1362

717-1363

718-0228 717-1020 716-0184 741-0589

710-0862A

717-O539 741-0340

721-0179

750-0767

736-0445 711-0918

717-1252

Wire Ring

Retaining--Ring

Hex Wash. TT-Tap Scr. 1/4-20 x

1.75" Lg.*

Hex Tap Scr. 1/4-20 x 1.25" Lg. Upper Housing Input Shaft

Thrust Washer 5/8" I.D. x .

1.25" O,D.

Pinion Input 14T Retaining Ring

Drive Shaft--R.H. Brake Flange Brg. 5/8" I.D. x 3/4"

Lg.

Bevel Gear 42T Small I.D. Bevel Gear 42T Large I.D.

Clutch Collar Miter Gear 15T (H.D.)

Snap Ring Thrust Bearing Pan Head Scr. 1/4-20 x .50"

Lg. w/Patch Axle R.H. Ass'y. Sleeve Bearing 3/4" I.D. x

1.0" Lg,

Oil Sea{ 3/4" I.D. Axle Spacer

FI-Wash..760" I.D. x 1.5"

O.D. Cross Shaft

Differential Can Ass'y. Parl of Ref. 28

Washer (See Below)

REF.

NO,

34 35

40 411 42 43 44 45 46

48 49 50 51

55 56

57 58

PART

NO.

736-0445

719-0313 718-0150 712-0273 736-0371

717-0700 761-0198

717-0682 717-0678 717-0538 761-0202 741-0337

61_-0011

741-0862

732-0863

714-0169

741-0335

736-0349

741-0343 710-1206

717-1364 736-0349

736-0495

737-0148

DESCRIPTION

FI-Wash..760" I.D. x 1.5" O.D. Lower Housing

Anti-Rotation Brkt.

Hex Nut 5/16-24 Thd. FI-Wash..344" I.D. x .875"

O.D.

Actuating Arm

Brake Yoke Puck Plate

Brake Puck Axle L.H. Ass'y.

Brake Disc Flange Bearing 5/8" I.D. x

15/16" Lg.

Shift Fork Ass'y. Ball Detent .250" Dia.

Spring Detent #9 Hi-Pro Key 3/16" x 3/4"

Dia. HT

Needle Brg. 5/8" I.D. x 1/2"

Lg.

FI-Wash. 5/8" I.D. x 1" O.D.

x .020 Thk.

Actuating Pin 5/16" Dia. Hex Wash Hd. Self-Tap Scr.

1/4-20 Thd. Differential Gear 58T FI-Wash. 5/8" I,D. x 1" O.D. x

.020 Thk.

Thrust Wash. 5/8" I.D. x 1"

O.D. x .025" Thk,

Washer (See Below) Grease_Shell (15 oz.)

**Ref. No. 32 736-0495 Thrust Wash. 5/8" I.D. x 1" O.D. x .025" Thk.

736-0336 FI-Wash. 5/8" I.D. x 1" O.D. x .030" Thk. 736-0494 Thrust Wash. 5/8" I.D. x 1" O.D. x .035" Thk. 736-0337 FI-Wash. 5/8" I.D. x 1" O.D. x .040" Thk.

**Ref. No. 60 736-0492 FI-Wash, .76" I.D. x 1.5" O.D, x .010" Thk.

736-0493 FI-Wash..76" I.D. x 1.5" O.D. x .020" Thk. 736-0351 FI-Wash..76" I.D. x 1.5" O.D. x .030" Thk. 736-0445 FI-Wash..76" I.D. x 1.5" O.D. x .060" Thk.

Page 30

TMO-3100002 TMO-3395309

Black

Yellow _ L_White Yellow

LBlack

_ _. Blue _

lO 8

• _i_ _

Green

Blue

i1Ei

13 14

REF.

NO.

1 2 3 4 5 6 7 8 9

PART

NO.

725-1438 725-1426 725-1625 725-0634 725-0925 725-0267 725-3169A 725-0562 629-0080

PARTS LIST FOR ELECTRICAL SYSTEM

DESCRIPTION

Battery Solenoid

Fuse 7.5 Amps Light Switch

Ammeter Ignition Switch

Safety Switch (Clutch) Electric Wire 32.5" Lg. Wire Harness

REF.

NO.

10 11 12 13 14 15 16 17

PART

NO,

726-0197 725-0803C 725-0759 725-1649 725-0963 725-1303 725-0980 725-1439 731-1284

DESCRIPTION

Cable Tie Safety Switch (Deck)

Safety Switch (Reverse) Socket

Bulb (Headlight) Safety Switch (Seat) Ground Wire 7.5" Lg. Safety Switch (Seat) Harness Conduit (Not Shown)

TMO-3100002 TMO-3395309

PARTS LIST FOR LAWN TRACTORS

REF, PART

NO. NO, DESCRIPTION

5 6 7 8 9

12 13

710-0776A

17450 17449

751-0474

16934 736-0170 712-0267 731-0511-12 737-0164 737-0143

16 H.P.

18 H.P.

726-0272 736-3067 710-0779A

Hex AB-Tap Scr. 1/4 x .62" Muffler Heat Shield Mtg.

Brkt.--R.H. (Not Shown)

Muffler Heat Shield Mtg.

Brkt.--L,H. Muffler Front Heat Shield

Spec, L-Wash. 5/16 x .88" Hex Nut 5/'16-18 Thd.

Trim Strip 12" Lg,

Pipe Nipple

Oil Drain Cap

Engine-B&S 402707-1511-01

(TMO-3395309)

Engine-B&S 422707-1510-01

(TMO-3100002) Clamp

FI-Wash..188" I.D. x .438"

Truss Mach. AB-Tap Scr. #10

x .5" Lg,

Page 31

USE THIS SHEET AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY.

i | _ SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

I _ ........ A POWER POLE

• ... I I I _ ............ A CORNER OF A BUILDING

I.... I I

l_'_ "'" ",... . l '

I'_._ ...... • I I _ ..... OR A FENCE POST

,-:,. i _>_ .... . I -"

,1 ) *'*o I

4) I _, ....

I_= nb _ • ",.. _-U O_

4) ' _ ! _ *",;7 O0.r.,.

L = .%'- • .... "._NT#u..

4) ;P, I -,,,,: too _0_

;- ,

,_. I """ .....

15°

r,)

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip, resulting in serious injury.

Operate RIDING mowers up and down slopes, never across the face of slopes. Operate WALK-BEHIND mowers across the face of slopes, never up and down slopes.

Page 32

SERVICE NATIONWIDE

Mor,cgommy Wind

HOW TO OBTAIN.

REPLACEMENT PARTS AND SERVICE

The merchandise you have purchased from us has been carefully

engineered and manufactured under Montgomery Ward's rigid quality standards and should give you satisfactory and dependable operation. However, like all mechanical merchandise, Jt may occa- sionally require adjustment, replacement parts or maintenance.

Toll Free Parts Sales Center

When you need a replacement part or accessory for a major appli- ance, home electronic item or lawn and garden product that is not under warranty or covered by a service contract or if you need the location of the nearest service facility, call our Parts Sales Center

toll free 1-800-323-1965.

Provide lhe following:

1. Model, serial number and all of the other data shown on the

model plate.

2. Also give the part number or numbers as shown in the parts list that came with Ihe product.

Replacement Parts wil! be made available at current prices. If requested, pnces will be quoted in advance when not listed.

H you order parts by mail, you will pay the transportation charges from the shipping point.

UNIT MODEL NO.

UNIT SERIAL NO.

ENGINE MODEL NO.

TYPE NO.

CODE NO.

PART NO. 770-8087H 133P670G088 132-670G088

PRINTED IN U.S.A.