Monte Carlo Fan Company MC223 Owner's Manual

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proof of purchase

DATE OF PURCHASE:

MODEL NUMBER:

To register your fixture, please visit our website www.montecarlofans.com

RETAILER NAME:

RETAILER ADDRESS:

MC223 Series light kit

Canadienne-française P. 5

UL Model NO. : MC223

2.7 kgs

5.94 lbs

Light kit weight

Cautions and Warnings

We thank you for selecting one of our superior quality products. We dedicate considerable time and effort
to ensure they are the best available.

GENERAL

CAUTION: To reduce the risk of fire and electric shock, this light kit should be used only with 5HLR54XX
series fan manufactured by Chien Luen Industries (Zhongshan) LTD.

To assure success of this installation be sure to read the instructions and review the diagrams thoroughly
before beginning. Follow the instructions that are applicable for your light kit.

Review the installation instructions supplied with your fan. Make sure that your fan has been installed and
wired properly to allow use with your light kit.

All electrical connections must be in accordance with local codes, ordinances, and national electrical
codes.

If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified
electrician.

CAUTION: Risk of electrical shock. Before starting installation, disconnect the power by turning off the
circuit breaker or removing the fuse at the fuse box. Turning the power off using the fan switch is not
sufficient to avoid electrical shock.

CAUTION

untrained personnel. If any servicing is required, the product should be returned to an authorized service
facility for examination or repair.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution and
care are factors that cannot be built into any product. These factors must be supplied by the person(s)
caring for and operating the unit.

NOTE: For normal installation, please use the plug system to install light kit. Figure A.
For installation where the fan doesn’t have a plug system, remove plugs (cut off plugs with scissors or

wire cutters) and wire lead wires from source to lead wires from light kit. Install wire nuts to all
connections making sure no filaments are exposed. Figure B

Use remote control that comes with fan to control up light and down light separately when used with fan.
If the light kit is available with Semi Flush Mount, use wall switch when the light kit is installed with semi

flush mount.

: The light source is designed for this specific application and can overheat if serviced by

Plug system

Fig. A Fig. B

© 2013 Monte Carlo Fan Company

Non plug system

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.
Skokie, IL 60077

www.montecarlofans.com

2

12/1/2013

GENERAL INSTALLATON

1

ON

ON

OFF

OFF

2 3

Before you begin installing the fan, Switch
power off at Service panel and lock
service disconnecting means to prevent
power from being switched on
accidentally. When the service

Remove set screws from switch housing.
Keep screws.

disconnecting means cannot be locked,
securely fasten a warning device, such
as a tag, to the service panel.

4 5 6

Switch housing

Light fixture

Unplug and remove the switch housing
from fan.

Blue

White

Black
White

Medallion

Remove medallion from switch housing
by removing its set screw.

7 8

Lift light fixture assembly up, connect
the plug from fan to the plug from
light kit assembly (switch housing).
Make sure the plugs are clasped
firmly.

Thread lead wires from light fixture through
central hole in switch housing and then
install switch housing onto light fixture by
turning clockwise till tight. Place lock
washer and hex nut provided over lead wire
from light fixture and tighten securely with

the thread rod of light fixture.

Install light kit assembly (switch
housing) onto the fan with set screws
removed in step 2.

Connect white wire from light fixture
with white wire from switch housing
and then connect black wire from light
fixture with blue wire from switch
housing.

9

Nut

Finial

Remove nut and finial from light
fixture. Keep parts.

© 2013 Monte Carlo Fan Company

3

12/1/2013