Monte Carlo Fan Company Ceiling Fans User Manual

Owner’s

Manual

Ceiling Fan Installation Instructions

For Mach One Series Fans

READ AND SAVE THESE INSTRUCTIONS

Quality Ceiling fans

Total fan weight

with light kit

included

Installation

SAFETY TIPS

ARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

W

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1

.

1999), including fire-rated construction.
U

se this unit only in the manner intended by the manufacturer. If y ou have an y questions contact the manufacturer.

2.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

3.
one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

4.
switched on accidentally . When the service disconnecting means cannot be lock ed, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagr ams.

5.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6

.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

7.
t

he floor to the trailing edge of the blade.

WARINING: MOUNT ONL Y T O AN OUTLET BO X MARKED ACCEPTABLE FOR F AN SUPPOR T. To reduce the risk of fire, electric shock, or

8.

personal injury , mount to outlet bo x or supporting system acceptable for fan support. (Mounting must support at least 35 lbs.)

9.

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

10.

Attach the mounting bracket using only the hardware supplied with the outlet box.

11.

T o reduce the risk of fire or electric shock, do not use this fan with an y solid state fan speed control device, or v ariable speed control.

12.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

13.

NEVER place a switch where it can be reached from a tub or shower.

14.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s oper ation. F ollow the heating equip­ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

15.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prev
on accidentally . When the service disconnecting means cannot be lock ed, securely fasten a prominent warning device, such as a tag, to the
service panel.

ent power from being switched

Phillips Screwdriver Wire Cutters Pliers Step Ladder

1

Unpack and inspect fan carefully to
be certain all contents are included.

4

TOOLS REQUIRED

2

Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting means
to prevent power from being switched on accidentally .
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.

5

3

Before installing this fan mak
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per­sonal injury
system acceptable for fan support.
(Mounting must support at least 35 lbs.)

6

, mount to outlet bo

Ring blade holder

e sure the outlet

Screws

A

from
step 5

x or supporting

B

Place fan body with light fitter point­ing upward. Attach the 3 blades as
shown in diagram above.

Carefully turn fan motor over so that the
upper housing is facing up. Remove the 3
screws holding the upper housing in
place. Lift upper housing to rev
motor. Save screws for step 6.

eal the

Attach ring blade holder to blades with
the 6 screws pro
above. Make sure all screws holding
blades are tight before proceding to the
next step
main body using reverse of step 5 as
shown in fig. B above.

vided as shown in fig. A

attach upper housing to

e-

. R