Monte Carlo 3MAVR70XXD User Manual

Owner’s Guide and Installation Manual

3MAVR70XXD Series Fan

CUL Model NO. : 3MAVR70XXD

Attach sales receipt to this card and retain as your proof of purchase

DATE OF PURCHASE:

MODEL NUMBER:

To register your fixture, please visit our website www.montecarlofans.com

RETAILER NAME:

RETAILER ADDRESS:

6 kgs

13.2 lbs

Total fan weight with light

Cautions and Warnings

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the
building structure (or the ceiling joist).

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With a general use, isolating Wall Control/Switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. BFR-G4D99910G1

manufactured by Chungear Industrial Co. Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
CAUTION: The light source is designed for this specific application and can overheat if serviced by untrained personnel. If any servicing is

required, the product should be returned to an authorized service facility for examination or repair.
All set screws must be checked, and re-tightened where necessary, before installation.
Note: Suitable for use in damp locations.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

© 2018 Monte Carlo Fan Company

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.
Skokie, IL 60077

www.montecarlofans.com

2

10/2017

1 2 3

Ceiling

ON

ON

OFF

OFF

Ceiling
Joists

2˝ x 4˝

Outlet
Box

Ceiling joist

Mounting
Bracket

Outlet Box

Screw/ Washers
/Spring Washers

Before you begin installing the fan, Switch
power off at Service panel and lock
service disconnecting means to prevent
power from being switched on
accidentally. When the service
disconnecting means cannot be locked,
securely fasten a warning device, such
as a tag, to the service panel.

Use AC 120V/60HZ power supply
only.

Before installing this fan makes sure the
outlet box is properly installed to the
house structure. Ensure the outlet box is
securely fastened by at least two points
to a structural ceiling member (a loose
box will cause the fan to wobble).
To reduce the risk of fire, electric shock,
or personal injury, mount to outlet box or
supporting system acceptable for fan
support.
(Mounting must support at least 35 lbs.)

4 5 6

SAFETY CABLE INSTALLATION

Safety cable

Lag screw

Safety cable

Washer

Lock washer

Junction
Box

Mounting
Bracket

Blade bracket

p

u

e

d

i

s

s

i

h

T

This side up

Blade

Blade rubber plug

Set screw

Use metal outlet box suitable for fan
support and use only the screws provided
with the outlet box (must support 35
lbs). Remove the two outlet box screws
provided with the box, aligning the holes
of the mounting bracket with the holes of
the outlet box. Reinstall the 2 outlet box
screws securely.

This side up

Blade bracket

Blade assemby

For Canadian installation and for USA fan
and light kit combinations over 35 lbs, in
both flush and downrod modes the safety
cable must be installed into the house
structure beams using 3” lag screws,
washers and lock washers provided.

Note

: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove
Knockouts In The Outlet Box.

© 2018 Monte Carlo Fan Company

Note: Make sure the side with a label
“This side up” is installed upward.
Aligning the holes on blade and the screw
holes on blade bracket as shown in
illustration, and then partially install the
set screws with blade rubber plug.
Screws provided. Tighten screws
securely after 2 set screws are installed.
Repeat this process for remaining blades.
Caution: Make sure the blade rubber
plug is in position.

3

Place motor assembly on a suitable area
of bottom Styrofoam for installation of
blade assembly.
Aligning the holes on blade bracket with
the screw holes on the motor, and then
partially install blade assembly onto the
motor with set crews provided.
Repeat this process for remaining blade
assemblies.

Tighten all set screws securely after
all the blade assemblies are installed
to motor.
Note: For precise installation of blade

bracket with motor, the set screws are
made with a little interference fit. It is a
normal condition.

10/2017

7 8 9

Downrod

Keeper
pin

Cross
pin

Yoke

Partially loosen downrod set screws from
yoke at top of motor assembly.
Remove preassembled cross pin and
keeper pin from downrod. Keep parts.

Canopy

Canopy ring

Yoke cover

Downrod

Place downrod over canopy, canopy ring
and yoke cover.
Thread lead wires and safety cable from
motor assembly through downrod.

Screwdriver

Cross pin

For easy installation of cross ping on next
step.

Carefully insert a phillips screwdriver through
yoke and downrod (don’t damage the lead
wires) as a guide and then push the cross
pin and pull the screwdriver in the meantime
as shown in illustration.

10 11 12

Mounting bracket

Tab

Keeper pin

Slip downrod into motor yoke, aligning
holes and install cross pin and keeper pin.
Insert cross pin through yoke and downrod
until point appears on the other side, and
insert keeper pin on cross pin.

Pull the downrod up tight against the
cross pin, and then evenly tighten the
downrod set screws on motor housing
yoke.

Place yoke cover on top housing of fan.
Warning: Cross pin and keeper pin must

Cross pin

Slot

Hanger ball

Install ball end of downrod into mounting
bracket opening. Align (engage) slot on
ball with tab on mounting bracket.
Warning: Failure to align slot on ball with
tab may result in serious injury.
Important: If using the angle mount,
make sure open end of mounting bracket
is installed facing the higher point of the
ceiling and make sure the ceiling angle is
not steeper than 15º.

be installed securely, failure to install them
will result in serious injury.

Attach Safety
Cable to Ceiling
Support Cable

Tab

Safety cable from fan

Set screw

Cable clamp

Connect the safety cable from fan to the
Ceiling support cable.
Slide cable clamp onto the safety cable
from fan. Place the end of cable through
the loop of ceiling support cable and then
feed end of cable into clamp hole and
firmly tighten set screw. Cut off excess
safety cable.
Make sure that when the safety cable is
fully extended the lead wires are longer
than the cable and no stress is placed on
the lead wires.

© 2018 Monte Carlo Fan Company

4

10/2018