Montague SEK15AH Installation Manual
Models:
SEK15A,SEK2-15A,SEK15AP,SEK2-
15AP, SEK15AH&SEK2-15AH
This manual is meant as a suppliment to the
Electric Vectaire manual, The contents herein describe the function and
operation of the Solid State Electronic Controls, For information on
Electric Vectaire Oven installation, operation, maintenance, service and parts,
refer to the Electric Vectaire manual part no. 4519-5.
These instructions should be read thoroughly before attempting installation.
Set up and installation should be performed by qualified installation personnel.
Keep area around appliances free and clear from combustibles.
PLEASE RETAIN THIS
MANUAL FOR FUTURE
REFERENCE.
***SPECIAL CAUTION***
DO NOT PLACE HIGH-HEAT PRODUCING EQUIPMENT ADAJACENT TO THE RIGHT SIDE
OF AN "SEK" VECTAIRE CONVECTION OVEN. EXCEEDING 185 DEGREES (F) (85 C)
SURFACE TEMPERATURES CAN CAUSE PREMATURE COMPONENT FAILURE NOT COVERED
UNDER THE MANUFACTURERS WARRANTY.
OPERATION
CONTROLS
STANDARD MODELS (SEK15A AND SEK2=15A-FIGURE 1)
1. "LIGHT-OFF" SWITCH CONTROLS THE OVEN INTERIOR LIGHTS.
2. "FAN-OFF" SWITCH CONTROLS THE FAN OPERATION. IT MUST BE ON FOR
POWER TO BE SUPPLIED TO THE ELEMENTS. WHEN THE DOORS ARE
OPENED, THE FAN WILL STOP.
3. THE "0-1" SWITCH TURNS ON POWER TO THE TEMPERATURE CONTROLLER
AND ENERGIZES THE DIGITAL DISPLAY.
4. THE CYCLE INDICATOR LIGHT BECOMES ILLUMINATED WHENEVER THE
CONTROL CALLS FOR MORE HEAT AND EXTINGUISHES WHEN THE CONTROL
IS SATISFIED.
5. THE TIME-SET KNOB IS USED TO SET THE AMOUNT OF COOKING TIME
DESIRED.
6. THE TEMPERATURE SET KNOB IS USED TO SET THE DESIRED COOK
TEMPERATURE.
*7. THE COOKING LOAD SWITCH REGULATES THE COOKING SENSETIVITY OF
THE OVEN. IN THE "NORMAL" POSITION THE HEATING ELEMENTS ARE AT
FULL CAPACITY, IN THE "LIGHT" SETTING THE HEATING ELEMENTS ARE
AT REDUCED CAPACITY. USE THE "LIGHT" SETTING FOR LESS DENSE
PRODUCTS, PARTIAL LOADS OR LONG LOW-TEMPERATURE COOK CYCLES.
8. KEY PAD CONTROLS . STANDARD MODELS CONTAIN ONLY TWO KEY-PADS. A
START-CANCEL-TIMER KEY IS USED FOR STARTING THE TIMER AND
CANCELLING THE BEEP ALARM, AND A TEMP-KEY WHICH WILL CAUSE
MEASURED OVEN TEMPERATURE TO APPEAR IN THE DISPLAY WINDOW WHEN
DEPRESSED.
* 480 VOLT UNITS HAVE NO "COOKING LOAD" SWITCH, AND OPERATE WITH
THE HEATING ELEMENTS AT FULL CAPACITY AT ALL TIMES.
PROGRAMMABLE MODELS (IE; SEK15AH AND SEK2-15AH--FIG. 2)
1. KEY-PAD-CONTROLS . PROGRAMMABLE MODELS CONTAIN NINE KEY-PADS.
THE START/TIMER AND TEMP KEYS ARE USED AS DESCRIBED WITH THE
STANDARD MODELS. THE SIX PROGRAM KEYS ARE NUMBERED AND ALLOW
THE USER TO PROGRAM AND STORE SIX INDIVIDUAL COOKING TIMES AND
TEMPERATURES. THE CANCEL KEY IS USED TO CLEAR A PRE-PROGRAMMED
COMMAND ONCE STARTED AND TO CANCEL THE END OF CYCLE BEEP.
COOK-N-HOLD MODELS (IE; SEK15AH AND SEK2=15AH--FIG. 3)
1. KEY PAD CONTROLS . IN ADDITION TO THE KEYS STANDARD WITH THE
PROGRAMMABLE MODE, COOK-N-HOLD MODELS INCLUDE COOK-HI-FAN AND ROAST-LOWFAN KEYS WITH WHICH TO CHANGE THE FAN SPEED. THERE IS ALSO A HOLD KEY WHICH
ALLOWS A HOLD TEMPERATURE TO BE MANUALLY SET OR PROGRAMMED INTO MEMORY.
OPERATIONAL DESCRIPTION
POWER UP (ALL MODELS)
ON INITIAL POWER UP THE TIME DIGITS WILL ALWAYS DISPLAY ZERO WITH COLON.
THE TEMPERATURE DIGITS WILL DISPLAY ZEROS WITH THE DEGREES INDICATOR
LIGHTED. THE "C" ANNUNCIATOR WILL ALSO BE LIT IF THE C OPTION IS
SELECTED. SUBSEQUENT POWER UPS WILL RESULT IN THE TEMPERATURE TIMER DIGITS
DISPLAYING THE PREVIOUS SET TIME AND TEMPERATURE WHEN POWER WAS REMOVED
FROM THE CONTROL.
MANUAL TEMPERATURE SELECTION AND OPERATION (ALL MODELS)
ROTATING THE TEMPERATURE DIAL CLOCKWISE WILL INCREMENT TEMPERATURE DIGITS
IN THE DISPLAY IN 5 F OR 1 C INCREMENTS. THE OVEN WILL START HEATING AS
SOON AS THE SET TEMPERATURE IS HIGHER THAN THE OVEN TEMPERATURE. THE
COOK ANNUNCIATOR WILL COME ON AND THE HIGH SPEED FAN WILL ENERGIZE WHEN THE
TEMPERATURE IS SET TO ANY NON-ZERO VALUE. THE TEMPERATURE DIGITS WILL
DISPLAY THE SET TEMPERATURE FLASHING AT AN APPROXIMATE 1-SECOND RATE
UNTIL THE OVEN REACHES SET TEMPERATURE. UPON REACHING SET TEMPERATURE THESE
DIGITS WILL BECOME STATIC. IF THE SET TEMP IS SET TO THE SAME TEMP
AS THE ACTUAL TEMP OF THE OVEN, THE DISPLAY WILL NOT FLASH.
ASSUMING A NEW SET TEMPERATURE IS ENTERED, WHICH IS LOWER THAN THE PREVIOUS
SETTING, THE NEW SET TEMPERATURE WILL FLASH UNTIL THE OVEN TEMPERATURE
HAS COASTED DOWN TO THIS NEW SETTING AND WILL THEN BECOME STATIC.
MEASURED OVEN TEMPERATURE CAN BE RECALLED BY PRESSING THE TEMP KEY. MEASURED
TEMPERATURE WILL BE DISPLAYED AS LONG AS THE KEY IS PRESSED. UPON RELEASE
THE DISPLAY WILL REVERT TO DISPLAYING THE SET TEMPERATURE.
TO TURN THE OVEN OFF WITHOUT POWERING THE CONTROL DOWN THE
TEMPERATURE DIALS CAN BE ROTATED COUNTER-CLOCKWISE UNTIL ZERO DEGREES ARE
SHOWN IN THE DISPLAY.
MANUAL TIME SELECTION AND OPERATION (ALL MODELS)
ROTATING THE TIMER SWITCH CLOCKWISE WILL INCREMENT THE TIME DIGITS-IN THE
DISPLAY IN THE FOLLOWING MANNERS
-1 MINUTE INCREMENTS UP TO ONE HOUR
-5 MINUTE INCREMENTS UP TO TWO HOURS
-10 MINUTE INCREMENTS UP TO TWELVE HOURS.
THE HR ANNUNCIATOR IS TO BE LIGHTED AT ALL THE TIMES IF THE
MINUTES/HOURS MODE IS SELECTED. THE MAXIMUM TIME ENTRY ALLOWABLE WILL BE
TWENTY-FOUR HOURS. COUNTERCLOCKWISE ROTATION OF THE ROTARY SWITCH WILL
DECREMENT THE COUNTER IN A LIKE MANNER. THE TIMER COUNT DOWN IS STARTED
BY MOMENTARILY PRESSING THE START/TIMER SWITCH. IF THE TIMER IS SET AND NOT
STARTED, THE TIME DIGITS AND THE COLON FLASH AT A ONE-CYCLE PER SECOND RATE.
ONCE STARTED, THE TIMER DIGITS BECOME STATIC BUT THE COLON REMAINS FLASHING.
WHEN THE TIMER REACHES ZERO, A REPEATING BEEP
Loading...