Montague RF - Fryers Specifications
Item No. ___________________________
Project ___________________________
Match Gas Fryers
Model RF40
Heavy-Duty Range
MODEL GUIDE
Model No. Overall Width Tanks
RF40
RF240
RD18
BURNERS & CONTROLS:
• Stainless steel atmospheric 55,000 BTU/hr burners
• Self-powered 200-375°F (93-190°C) thermostat-gas valve
• Automatic ignition safety pilot
• High temp limit control & built-in gas pressure regulator
RD18 DRAIN CABINET [ONLY]
• Matching cabinet with hinged door
• Stainless steel perforated lift out top screen
• Stainless steel slide-out grease catch pan
STANDARD WARRANTY:
• One Year, Parts & Labor
AGENCY APPROVALS
• NSF Listed
• CSA Design Certified to ANSI Z83.11, CSA 1.8
18” (457 mm) 1 40 lb (18 kg)
36” (914 mm) 2 80 lb (36 kg)
18” (457 mm) Basket Drain Cabinet
Quantity ___________________________
Shortening
Capacity
SHORT/BID SPECIFICATION
Fryer shall be a Montague Legend Range Match Model [Specify one]:
M
RF40, an 18” (457 mm) wide unit with a unique 110,000 BTU/hr
burner and a single 40 pound oil capacity frypot
M
RF240, a 36” (914 mm) wide unit with two 110,000 BTU/hr
burners with twin 40 pound oil capacity frypots
M
RD18, an 18” (457 mm) wide matching fry basket drain cabinet;
… with satin finished stainless steel front, cabinet access door(s),
bottom and sides; two 5-1/2” (140 mm) wide fry baskets per frypot and
removable stainless steel basket hangers; 6” (152 mm) height adjustable
legs and 11” (279 mm) high flue riser standard; plus all the features
listed and options/accessories checked:
STANDARD CONSTRUCTION FEATURES:
• Satin finish stainless steel front, sides & bottom
• Hinged stainless steel door(s) provides easy access to controls
• Other surfaces painted black
• Welded stainless steel frypot with deep cool zone
• 1” (25 mm) ball-type front drain valve, with extension pipe standard
• Twin wire fry baskets with insulated handles
• Sturdy, removable, stainless steel basket hangers
• 11” (279 mm) high flue riser with insulated heat shield for cooler
operation
• 6” (152 mm) height-adjustable stainless steel legs
• 1-1/4” NPT front gas manifold with 1/2 unions for battery connection
HDS-37 [Rev. 10/10]
THE MONTAGUE COMPANY • 1830 Stearman Avenue, Hayward, CA 94545 • 800 345-1830 • Fax: 510 785-3342 • montaguecompany.com
Item No. ___________________________
Heavy-Duty Range Match
Gas Fryers
Gas Fryers
OPTIONS GUIDE:
General:
M
Extra baskets, Twin: ___ ea.
M
Extra baskets, Triple: ___ [set of three]
M
Side Splash 8” (203 mm) high [for left or right]
M
Stainless steel back panel
M
18” (457 mm) high-back flue riser
M
Inset covers, stainless steel: ___ ea. [frypot]
M
Portable filtering system [for use with RD18]
Manifolds: [Left rear with pressure regulator]:
M
1” NPT up to 500,000BTU/hr
Manifold Cap:
M
left side M right side
Stainless Manifold Cover:
M
left side M right side
Project ___________________________
Quantity ___________________________
Dimensions in brackets are millimeters
INSTALLATION REQUIREMENTS & SHIPPING INFORMATION
1. Fryers must be installed in accordance with local codes or in their absence with the
National Fuel Gas Code: ANSI Z223.1; Natural Fuel Gas Code: CAN/CGA-B149.1 or Propane
Installation Code: CAN/CGA-B149.2, as applicable. Compliance with codes is the
responsibility of the Owner and Installer.
2. An adequate ventilation system is required. Refer to National Fire Protection Association
Standard No. 96, “Vapor Removal from Cooking Equipment.”
3. This appliance is intended for commercial use by professionally trained personnel.
NOT intended for Residential Use.
4. Specify installation elevation: _____________ if above 2,000 ft(610m).
5. GAS INLET SIZE (All Models): 1-1/4 NPT front manifold with 1/2 union on each end
provided for battery connection. A properly sized gas pressure regulator must be furnished
by the Installer.
6. The incoming gas line pressure into the regulator should be 8”-14” w.c. for natural gas,
and 12”-14” w.c. for propane gas.
M Natural M Propane
4.0” WC 10.0” WC
Models:
RF40
RF240
Specify Type of Gas:
Manifold Pressure:
Burners BTU/hr* (kW) BTU/hr* (kW)
1 110,000 (32.2) 110,000 (32.2) 251 lbs (114 kg) 85 18/.5
2 220,000 (64.4) 220,000 (64.4) 423 lbs (192 kg) 85 36/1.0
RD18
*Total BTU Input/firing rate
Minimum
Clearances
Combustible
Construction
Noncombustible
Construction
From Back Wall NA 6” (381 mm)
Left & Right Side 6” (152 mm) 0”
With 6” (152 mm) legs Suitable for installation
on combustible floors
Shipping
Weight
Shipping
Class
Cube
(Crated)
3/m3
ft
238 lbs (108 kg) 85 15/.4
RF240 Entry Clearance: 36-1/8” (918 mm) uncrated.
Due to continuous product improvements,
specifications are subject to change without notice.
1830 Stearman Avenue, Hayward, CA 94545
800 345-1830 • Fax: 510 785-3342
www.montaguecompany.com
HDS-37 [Rev. 10/10]
Loading...