Montague 136LB-UFLC-36R Operator’s Manual

INSTRUCTION MANUAL

Addendum

MONTAGUE

Gas Fired Heavy Duty Counter,

Standard, and Convection Ranges

with Electronic Ignition

Models:

C12, C18, C24 & C36 Series

M12, M18, M24 & M36 Series

124, 136 & V136 Series

These instructions should be read thoroughly before attempting installation.

Set up and installation should be performed by qualified installation personnel.

Keep area around appliances free and clear from combustibles.

PLEASE RETAIN THIS MANUAL

FOR FUTURE REFERENCE.

THE MONTAGUE COMPANY

1830 Stearman Avenue P.O. BOX 4954

HAYWARD,CA 94540-4954

TEL: [phone] FAX: [phone]

CONTENTS

INSTALLATION ………………. 1 MAINTENANCE…………… 6
OPERATION……………...……. 4 SERVICE…………………... 7

IMPORTANT

WARNING:
Improper installation, adjustment,
alteration, service or maintenance
can cause property damage, injury
or death. Read the operating and
maintenance instructions thor­oughly before installing or servic-

FOR YOUR SAFETY:

Do not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.

ing this equipment.

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS MUST BE
POSTED IN A PROMINENT LOCATION. THIS INFORMATION MAY BE OBTAINED BY
CONSULTING THE LOCAL GAS SUPPLIER.

SHIPPING DAMAGE CLAIM PROCEDURE

For your protection, please note that equipment in this shipment was carefully inspected
and packed by skilled personnel before leaving the factory. The transportation company
assumes full responsibility for safe delivery upon acceptance of this shipment.

If shipment arrives damaged:

1. VISIBLE LOSS OR DAMAGE—Be certain this is noted on freight bill or express receipt,
and signed by person making delivery.

2. FILE CLAIM FOR DAMAGES IMMEDIATELY—Regardless of the extent of damage.

3. CONCEALED LOSS OR DAMAGE—If damage is unnoticed until merchandise is un-
packed, notify transportation company or carrier immediately, and file ―concealed dam­age‖ claim with them. This should be done within fifteen (15) days of date that delivery
was made to you. Be sure to retain container for inspection.

We cannot assume responsibility for damage incurred in transit. We will, however, be glad
to furnish you with necessary documents to support your claim.

2

INSTALLATION

The Montague gas ranges are manufactured for use with the type of gas indicated on the name­plate.

The Montague heavy duty gas convection oven type ranged are produced with the best possible
material and workmanship. PROPER INSTALLATION IS ESSENTIAL FOR SAFE AND
EFFICIENT TROUBLE-TREE OPERATION.

THE INSTALLATION INSTRUCTIONS CONTAINED HEREIN ARE FOR THE USE OF

Qualified installation personnel are individuals, a firm, corporation, or company which either in
person, or through a representative are engaged in, and are responsible for:

A. The installation or replacement of gas piping or the connection, installation, repair, or servicing

B. The installation of electrical wiring from the electric meter, main control box, or service outlet to

QUALIFIED INSTALLATION AND SERVICE PERSONNEL ONLY. INSTALLATION

OR SERVICE BY OTHER THAN QUALIFIED PERSONNEL MAY RESULT IN

DAMAGE TO THE RANGE AND/OR INJURY TO THE OPERATOR.

of equipment, who is experienced in such work, familiar with all precautions required, and has
complied with all requirements of state or local authorities having jurisdiction. Reference:
National Fuel gas code Z223.1-1984, Section 1.4.

the electric appliance. Qualified installation personnel must be experienced in such work, be
familiar with all precautions required, and have complied with all requirements of state and local
authorities having jurisdiction. Reference: National Electric Code, ANSI/NFPA No. 70-1984.

READ CAREFULLY AND FOLLOW THESE INSTRUCTIONS

THE RANGE(S) MUST BE INSTALLED IN ACCORDANCE WITH LOCAL CODES, OR IN THE
ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI A223.1-1984,
INCLUDING:

1. The appliance and its individual shutoff valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of 1/2
psig. (3.45 kPa).

2. The appliance must be isolated from the gas supply piping system by closing its individual
manual shutoff valve during any pressure testing of the gas supply piping system at test
pressure equal to or less than 1/2 psig. (3.45kPa)

THE UNIT WHEN INSTALLED MUST BE ELECTRICALLY GROUNDED IN

ACCORDANCE WITH LOCAL CODES, OR IN ABSENCE OF LOCAL CODES, WITH

THE NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70-1984.

PROVISIONS MUST BE MADE FOR ADEQUATE AIR SUPPLY TO THE UNIT.

3

INSTALLATION

ELECTRICAL CONNECTION

Unless otherwise specified, the range is equipped with a 6 ft. flexible supply cord for 115 VAC,
60 Hertz. A terminal block is provided for 208-240 VAC, 60 or 50 Hertz, single phase units. The
wiring diagram is located on the back of the range.

THIS APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN

ACCORDANCE WITH LOCAL CODES, WITH THE NATIONAL ELECTRIC CODE,

ANSI/NFPA NO. 70-1984.

1. 115 VAC—60 Hz—Single Phase

Ranges with this electrical rating are factory supplied with a three-wire cord and three–
prong plug which fits any standard three-prong grounded receptacle. A separate 15 amp.
supply is needed for each oven.

WARNING: ELECTRICAL GROUNDING INSTRUCTIONS:

THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR

YOUR PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED

DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. DO NOT

CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG.

II. 208-240 VAC—60 Hz–Single Phase (2 Wire)

Ranges with this electrical rating are factory supplied with a terminal block. To connect supply
wires, remove cover from connection box at right rear of range. Route supply wires and ground
wire through hole with strain relief fitting at top of connection box. Attach ground wire to ground
wires to proper terminal block. Attach ground wire to ground lug inside connection box. See
wiring diagram for proper connections.

III. 220 VAC– 50Hz– Single Phase (2 Wire)

Follow steps outlined in (II.) above, refer to wiring diagram for proper connection.

4