Monster SC60 HSD Instruction Manual

Model #:

SC60 HSD

MONSTER SC60 STEAM CLEANER

INSTRUCTION MANUAL

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

ENGLISH

SAVE THESE INSTRUCTIONS

When using an electrical appliance, basic safety precau­tions should always be observed, including the following:

Read all instructions before using this appliance.

WARNING:

To reduce the risk of re, electrical shock, or injury:

1. This appliance is authorized for household/residential use only.

2. Do not immerse the Steam Cleaner in water or other liquids. Always turn
off and unplug appliance when lling with water.

3. Do not allow to be used as a toy. Close attention is necessary when
used by or near children, pets or plants. Do not leave Steam Cleaner
unattended. Always unplug unit when not in use.

4. Use only as described and for the uses described in this manual. Use only
manufacturer’s approved and supplied parts and accessories. Use of
other accessories is not recommended and will void warranty.

5. Do not use if power cord or plug has been damaged, or if any part of
appliance has been dropped, damaged, left outdoors, or dropped in

water. Do not attempt to disassemble or repair appliance. Return it to

manufacturer or an authorized service center for examination or repair.

6. Do not wrap cord too tightly around appliance. Never carry by the cord,
or yank to disconnect from an outlet. To unplug, always grasp plug to
remove from outlet – do not pull on cord.

7. Do not handle cord or appliance with wet hands or without shoes on.

8. Keep cord away from heated surfaces (e.g., cooking surfaces), and

sharp edges and corners.

9. Follow all labels and marking instructions on Steam Cleaner.

10. Do not put any objects into openings. Do not use with any opening

blocked.

11. Keep hair, loose clothing, ngers, and all parts of body away from
openings and moving parts.

12. Before lling with water or emptying, always turn appliance off, unplug
appliance and allow it to cool completely. Always turn the Boiler Cap
slowly to open the water tank – this will allow any remaining steam to
escape gradually.

13. Use caution while emptying the appliance. Contact with hot metal
parts, hot water or steam may cause burns.

14. Be sure Boiler Cap is (and remains) closed during use.

15. Never use cleaning solutions, perfumes, oils or other chemical substances

other than tap or distilled/demineralized water in the Steam Cleaner. Use

of chemicals may damage appliance and will void your warranty.

16. When in use, never turn the appliance on its side. Do not direct steam at
people, animals or other electrical equipment (i.e, inside an oven).

IMPORTANT SAFE TY INSTRUCTIONS

2

Safety Instructions

SAVE THESE INSTRUCTIONS

17. Do not operate around ammable or combustible liquids such as gaso­line, or in areas where fumes may be present.

18. To reduce the likelihood of circuit overload, do not operate another
high wattage appliance on the same circuit. Plug in to a standard (120V,
60Hz) electrical outlet.

ATTENTION: This appliance is equipped with a 3-prong grounded power cord.
Insert only into a 3-prong grounded electrical outlet. Do not try to remove the
contacts of the grounded connection.

19. Do not use extension cords or outlets with inadequate voltage. Use an
8-ampere extension cord. Lower amperage cords may overheat.

20. Store appliance indoors in a cool, dry place.

21. If appliance is damaged, it must be repaired by manufacturer or its
service agent or a similarly qualied person in order to avoid safety issues

to the operator.

22. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of appliance by a person responsible for their safety.

23. Read and follow all important notices in this guide.

3

Safety Instructions

*IMPORTANT*

Please read all of the instructions for use and Important Safety Instructions
carefully. Remove and discard all packaging materials and keep them
out of the reach of children.

CAUTIONS

• Always drain condensed water from hose before use or if unit has been

left idle for a period of time. To drain hose, direct Nozzle into a sink or
other appropriate container and slide the Steam Control forward on the
Steam Gun. Once hose is emptied, normal use may be resumed. Never
direct nozzle towards people, animals or plants.

• Extreme care should be taken when opening the Boiler Cap as it may

become hot during use and escaping steam can cause scalding.

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

1

4

3

2

6

5

14

8

1110

9

13

12

7

15*

16*

17*

1 - Steam Gun
2 - (2) Extension Tubes
3 - Brush Adapter
4 - Floor Brush
5 - Boiler Cap
6 - Power Indicator Light
7 - Flexible Steam Hose
8 - Shoulder Strap

9 - Filler Funnel
10 - Nylon Detail Brush
11 - Window Squeegee
12 - Detail Nozzle
13 - Scraper
14 - Cotton Cloth
15 - Caddy/Wall Bracket*
16 - Small Brush*
17 - Carpet Slider*

What’s Inside? & Product Description

4

What’s Inside? & Product Description

Technical Data
Adapter Input: 120V~, 60Hz

Power: 1450 watts
Boiler: Stainless Steel
Boiler Capacity: 1.2 liter/2 pints
Max. Steam Temp.: 130°C/266°F

*Only available with Value Pack - see pages

15-19 for Value Pack Features & Details.

One (1) Steam Cleaner

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

Features SC60 Accessories

5

Features & SC60 Accessories

SC60 Steam Cleaner Features

1. No need for detergents or chemicals. Just add water.

2. Lightweight and portable.

3. Heavy-duty, crush-proof hose.

4. Steam Gun locks in as carry handle.

5.Versatile, quick-change accessories.

6. Adjustable steam control.

7. Stainless Steel Boiler –
non-corroding, 18/10 stainless steel

boiler - welded construction.

8. Multiple uses – clean bathrooms, kitchens, living
areas, pet areas, appliances and much more.

Accessories - Attachment & Descriptions*

* Additional Accesories are available with the purchase of a Value Pack.

See “Value Pack Features & Details” on pages 15-19 of this manual.

A. Connecting Brush Adapter to Floor Brush

1

2

Continued on next page

180°

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

6

Cleaner Accessories

SC60 Accessories

Accessories (continued)

WARNING: Always ensure appliance is shut off and not steaming

when attaching an accessory to the unit.

C. Attach Extension Tube to Detail Nozzle

D. Attach Nylon Detail Brush to Detail Nozzle

E. Attach Scraper to Detail Nozzle

2

*CLICK

*CLICK

B. Attach Extension Tube to Window Squeegee

The Window Squeegee is very useful
for cleaning large windows, ceramic,

tiled or marble surfaces.
To use: Connect Window Squeegee

to Steam Gun or Extension Tube(s) for
hard to reach surfaces. Apply steam
liberally, rub with soft spongy edge,
then remove excess water and dirt

with squeegee edge.

CAUTION: When cleaning windows, always avoid any sudden changes
in temperature to prevent glass breakage or cracks.

The Detail Nozzle is very useful for
cleaning hard to reach areas. It is

ideal for radiators, door and window
jambs, shutters and sanitary xtures.

To use: Attach Detail Nozzle directly
to the Steam Gun or Extension Tubes.

The Nylon Detail Brush is best for
cleaning grout between tiles, ceramic

and marble.

To use: Push the Nylon Detail Brush on
the end of the Detail Nozzle. (Detail

Nozzle should be connected to the
Steam Gun or Extension Tubes.)

The Scraper is best for removing wall­paper and also anything that can
be scraped from a at surface, e.g.,
grease deposits in an oven. It is also

useful when defrosting freezers.
To use: Push the Scraper on the end of

the Detail Nozzle. (Detail Nozzle should
be connected to the Steam Gun or
Extension Tubes.)

Press button

Press button

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

7

Before Use & Using Your Steam Cleaner

Before Use

3

4

Filling Steam Cleaner with Water

WARNINGS

•

Carefully read all instructions before removing Boiler Cap.

•

Always unplug appliance and be sure it has cooled

completely before lling the Boiler.

Connecting Extension Tube(s)

• Attach one Extension Tube to Steam Gun on Flexible Steam Hose.

• To attach Extension Tubes together, press down the locking button

while sliding Tubes together. Be sure button and hole line up and

button locks in place. To disconnect, press the locking button and

pull the two sections apart.

WARNING: Always ensure appliance is shut off and not steaming

when attaching an accessory to the unit.

Follow these instructions to avoid overlling the Boiler.

• Be sure appliance is unplugged, and has

cooled for at least 10

minutes before lling with water.

• Carefully remove Boiler Cap by

turning it counterclockwise.

• Pour in a maximum of 1.2 L/2 pints
water using the provided Filler Funnel.

Make sure that

water does not overflow.

• Replace Boiler Cap by turning it clockwise.

• Plug unit into 3-prong, grounded outlet.

• Power Indicator Light will illuminate, unit will

produce steam and water tank will become

pressurized. If using cold water, heating time

is about 5 minutes. Using hot water reduces
heat time.

NOTE: Never turn on Steam Cleaner if Boiler is empty.

*IMPORTANT*

Use tap water – distilled or demineralized water if tap water is too
hard.

DO NOT add detergents, perfumes, oils or other chemical

substances.

Using Your Steam Cleaner

Max. 1.2l

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

Using Your Steam Cleaner

8

Using Your Steam Cleaner

Attaching Floor Brush to Extension Tube

A. Attach Brush Adapter to Floor Brush

Attaching Cotton Cloth to Floor Brush

A Cotton Cloth can be t on the Floor Brush to absorb dirt and
protect delicate surfaces. It can also be used on vertical washable
surfaces following the same procedure as for the oor.

B. Attach Floor Brush & Adapter to Extension Tube

Attach Extension Tube to Brush Adapter by pressing the locking

button while sliding Tube into Brush Adapter. Be sure button and

hole line up and button locks in place. To disconnect, press the

locking button and pull the two pieces apart.

5

6

*IMPORTANT*

To avoid scratching surfaces when using Floor Brush on wood oors or
painted walls and ceilings, securely attach Cotton Cloth to Floor Brush.
Make sure Brush bristles do not break through. If necessary use 2 cloths.

1. Place Floor Brush on

Cotton Cloth.

2. Fold Cloth as shown
below.

3. Fold other side of Cloth
as shown below.

4. Place folded end under

cloth holder (as shown).

5. Repeat for other end of Brush,

pulling Cloth to stretch it taut.

Attaching Cotton Cloth

180°

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

9

Using Your Steam Cleaner

Using Your Steam Cleaner

7

8

Regulating Steam

The amount of steam can be regulated by
sliding the Steam Control on top of the Steam
Gun. Move forward to increase steam – backward
to reduce steam.

IMPORTANT: When the Steam Cleaner has run out of water,
steam, output will cease. Follow rell instructions (page 12)
to use your Steam Cleaner again.

Attaching Shoulder Strap

Using the detachable Shoulder Strap allows for greater freedom of

movement when both hands are needed for cleaning tasks.
To attach Shoulder Strap to the Steam Cleaner,

simply snap Shoulder Strap hooks on the

connecting rings found on unit.
When using Steam Cleaner with the Shoulder

Strap, avoid rocking or tilting the unit excessively
as this may cause water to enter the hose and

be discharged along with the steam.

CAUTION: We recommend testing the weight of the
Steam Cleaner before using it with the Shoulder
Strap. This is to prevent potential injury and ensure
it is not too heavy for you to carry comfortably.

9

Usage Suggestions

• For vertical surfaces, always wipe excess water from the top
down. This catches dirty water before it drips on clean surfaces.

• Avoid changing attachments back and forth while cleaning.

• Start with the smallest brush to clean tight spots and corners rst.

• Wipe dirt as soon as possible, otherwise it will dry and re-adhere

to the surface.

To Strip off Floor Wax: Use Floor

Brush for open areas and Nylon

Detail Brush for corners or tight

areas - no Cloth, slow strokes. Work
a small area at a time, removing
the oor wax from the oor. When
all wax has been stripped, imme­diately clean oor and brushes

with water before residue hardens.

Go back over stripped area with
Floor Brush (with Cloth attached)
to remove any remaining residue

before re-polishing.

Wood, Vinyl and Marble Floors

Use the Floor Brush with Cotton

Cloth attached. Move Brush across
oor as if you are mopping. When
Cloth is soiled, turn it over or replace
it with a clean Cloth. If you are wor­king on a very dirty area, move the
Brush over the area slowly, several
times. If it is a wood oor, move
quicky to avoid heat or moisture

buildup in the wood.

NOTE: Unsealed wood floors i.e.,

un-painted or unvarnished wood
should not be steam cleaned.

Continued on next page

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

10

Using Your Steam Cleaner

Using Your Steam Cleaner

9

Usage Suggestions (continued)

CAUTION: Always determine the
color-fastness of any fabric –
especially with reds or blues – by
taking a clean, damp, warm towel
and gently rubbing a small hidden
part of the furniture. If color comes
off on the towel, you may need to
have the piece dry cleaned.

Window, Glass Surfaces and
Mirrors

Use the Window Squeegee.

Work with the steam jet on, using
top to bottom movements. Use

Squeegee with the steam off to
clear water from the glass. To do

this without streaking, use lateral
movements from the top to the

bottom of the surface.

Blinds

Use the Nylon Detail Brush to clean
blinds. Move Brush over the surfa­ce, allowing enough time for the

steam to penetrate.

Work quickly on PVC blinds. Test

for color fastness on fabric blinds
before using.

Fiberglass or Stainless Steel
Surfaces

Use Floor Brush or Nylon Detail
Brush. Slowly move Brush over the

surface to be cleaned. The steam

will emulsify the dirt and grease

on the surface. Follow with Cotton

Cloth over Floor Brush to remove
excess moisture and residue.

Tip: An old polishing method for
stainless steel is to wipe it down
with soda water after it’s cleaned.

Soap Scum

Soap scum dissolves almost imme­diately under a combination of

heat and moisture. Rinse surface
afterward with a small amount

of water or go back over it once

more with a clean cotton cloth.

NOTE: Soap scum will sometimes
develop a hard surface from
waterborne minerals. If this is the
case, use Floor Brush (no Cloth) to
break up this surface. Or, spray

or wipe rst with lemon, vinegar

or soda water to soften minerals.
Moving too slowly can dry out the

Polished Floors: Wrap clean Cloth

around Floor Brush, brush quickly.
This will cause dirt to be removed
but not the wax.

Vinyl Floors: Work quickly and
do not allow heat to build up on
any kind of vinyl – it can affect its

texture.

Tile Floors: Clean grout between

tiles using the Detail Nozzle and
Nylon Detail Brush. Use Floor Brush

with Cloth attached to clean tiles.

Move Floor Brush slowly across the
oor to remove excess moisture

and residue.

For tile areas that are very dirty,
remove the Cloth and agitate with
Brush. Do not let area dry before
you wipe it up.

Spot Cleaning (Carpets)

Use the Detail Nozzle with or without
the Nylon Detail Brush. Move slowly
over soiled area, allowing steam

to penetrate. Agitate with Detail
Brush or clean Cloth. Dab the spot

with Cloth (do not rub). Repeat as
necessary to remove stain. Vacuum
only after the carpet has comple­tely dried. Always test color fastness

of carpet in an inconspicuous area

before cleaning. If your Steam Cle­aner fails to remove stubborn stains,
a commercially available carpet
shampoo may be required.

DO NOT add cleaning solutions,
perfumes, oils or any other
chemicals to the water used in this
appliance. This may damage the
unit or make it unsafe for use.

Upholstery

Use Floor Brush (with Cloth), atta­ched directly to the Steam Gun.
Use fast, light strokes, and avoid

getting the fabric wet. Be patient
with stubborn spots. Work on a spot

gently for no more than a minute at
a time, then wait 5 minutes for the
area to dry and repeat. Use circular
movements or back-and-forth and
side-to-side movements to get all
sides of surface bers. Finish by
brushing in one direction to give the

fabric a uniform appearance.

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

11

Nicotine and Tar

Nicotine and tar dissolve at high

temperatures and become a light

yellow oil that has the consistency

of sewing machine oil. When the

nicotine/tar lm is touched by a
hot Cotton Cloth clipped over
the Floor Brush, it immediately
dissolves into the cloth. You can
remove it from at surfaces as fast
as you can move the Brush over

the surface.

Removing Wax, Tar, Etc.

Many stains are only stuck on the

surface of materials and can be

easily and quickly removed by
“blowing” excess material away

from the surface at an angle.

This is accomplished by using the
Detail Nozzle.

Hold a Cotton Cloth to the side to
catch loose residue as it is blown

by the Nozzle.

NOTE: Always vacuum any loose
residue off the surface before you
apply steam to it.

Oven

When cleaning an oven, use the
Nylon Detail Brush to clean around
the elements and drip trays. Use
Detail Nozzle and Detail Brush
for cracks, crevices, and hard to

reach areas.
Refrigerator

Use Detail Nozzle to blow away dirt

in the ice machine and on door

seals. The steam will not dry out or

crack the seals.

Can Openers & Other Kitchen
Equipment

These can be easily cleaned with
the Nylon Detail Brush on the
Nozzle to get into all the nooks and

crannies.
Microwaves & Small Appliances

Use Nylon Detail Brush.

WARNING: Always unplug small
appliances before cleaning.

Kitchen Work Surfaces

Use Floor Brush with Cloth at-

tached. For heavily soiled areas,
use Brush without the Cloth, rst in
order to loosen the debris, then fol­low with Cloth attached to nish.

soap scum and leave a gritty resi­due on the surface. If this happens,
apply steam with the Floor Brush (no
Cloth) again, and re-clean.

Bathroom Areas

To clean the bath or shower area,
use the Nylon Detail Brush for grout,
shower door tracks, hard to get
areas and heavily soiled areas. The

Window Squeegee will be the most

efcient way to clean the rest of the

tiled area and glass shower doors.

Allow plenty of time for the heat to

penetrate the surface. This is espe-

cially helpful in the shower area if

there is tile or grout.

To clean sanitary xtures, use the
Detail Nozzle with or without the
Nylon Detail Brush. Use a terry cloth

towel or paper towel to wipe up

excess moisture and residue.
Use Nylon Detail Brush to clean the

sink and taps.

Garden Furniture

Use either of the brushes depending
on the surface area.

Work quickly when cleaning resin

outdoor furniture.

Exterior Areas

To clean car interior, use the Floor
Brush with Cotton Cloth attached,
just as in the home. You should not
expose the bristles to leather – use
only the Brush with Cotton Cloth
attached. For detailing wheels, use
the Detail Nozzle and Nylon Detail
Brush. Exterior windows are clea­ned best by applying steam with
the Detail Nozzle and wiping with a

paper towel.

To clean bicycles: use the Nylon

Detail Brush.

Articial Plants

Use Detail Nozzle only, to blow off

dust and dirt.

Fabric Steamer

The Monster SC60 is excellent for
removing wrinkles from fabrics.
You can use the Monster SC60 as
a fabric steamer. Simply steam

the surface from a distance. The

dry steam removes wrinkles and
refreshes the fabric without leaving

it wet.

Using Your Steam Cleaner

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786

Relling the Boiler During Use

WARNING:

Let unit

cool 10 minutes before opening Boiler Cap

.

Use care when opening the Boiler Cap – it may still be hot and
steam may escape, causing burns. If Boiler is still hot, water may
spurt out during relling – this can also cause burns.

• Unplug appliance.

• Place towel or cloth over Boiler Cap. Slowly turn Boiler Cap
counterclockwise and release any remaining steam. If hissing,
wait until last of steam escapes and hissing stops before removing

Boiler Cap.

•

Be sure unit has cooled 10 minutes before relling with water.

• Rell Boiler with a maximum of 1.2L (2 pints) of water, using Filler

Funnel. (Only use the Filler Funnel supplied. Its nozzle is made from

a heat resistant material to prevent it from melting when lling a

hot boiler. Other plastic funnels can melt and become welded to
the inside of the boiler spout voiding your warranty.)

• Firmly screw Boiler Cap back on by turning it clockwise.

• Insert plug into 3-prong electrical outlet.

REMINDERS

• We recommend using distilled or demineralized water as the
best way to care for and utilize your Steam Cleaner.

• If tap water is too hard, use distilled or demineralized water to
avoid the risk of staining pale colored fabrics.

• Do not add detergents, perfumes, oils or other chemical

substances.

Using Your Steam Cleaner

10

12

Using Your Steam Cleaner

Turning Steam Cleaner Off

• Unplug Steam Cleaner to turn Off.

• Any remaining water can be left in the unit.

NOTE: We recommend loosening and removing the Boiler Cap after
using appliance to ensure it does not stick for next use. Be sure to let

unit cool before removing Cap.

11

For Authentic Monster Replacement Parts

Canada:

888.978.3262 US: 888-896-8786