Monoprice PID-8475 User Manual
Recessed Low Voltage Media Plate
DataComm Electronics’ new, patented
Recessed Low Voltage Media Plate
with Duplex Receptacle offers the
with Duplex Receptacle
45-0031-WH
convenience of a duplex receptacle and
a recessed plate with enough room to
store the low voltage cables behind
your flat panel TV.
Features
Low profile design fits behind the
industry’s thinnest mounts and TV’s
45-0031-WH - Front View
Conceal multiple AV cables behind
your flat panel TV
15 Amp/125 Volt tamper resistant,
duplex receptacle*
Old work box included
Mounting wings are molded into the
media plate and fasten tightly
against the back of the drywall
Quick and easy to install
Top View of 45-0031-WH Mounted Between Studs
No additional parts needed
Part #
45-0031-WH
This product is patent protected by U.S. Patent numbers
D553475, D554475 and 7390964
RoHS Compliant
* UL Listed Component
Recessed Low Voltage Media Plate
with Duplex Receptacle, White
Description
Min. Order/
Master Ctn.
1/16
45-0031-WH – Back View
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.datacommelectronics.com
Instruction / Installation Sheet
DataComm Electronics 45-0031-WH Recessed Low Voltage Media Plate with Duplex Receptacle
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.datacommelectronics.com
Parts Included:
1. 45-0031-WH Recessed Low Voltage Media Plate
2. Old Work Electrical Box
3. 15 Amp/125 Volt Tamper Resistant
Duplex Receptacle
4. Four (4) Screws
Use DataComm Electronics’ Recessed Low Voltage Media Plate with Duplex Receptacle to install low voltage cables behind your flat panel TV, your amplifier
or other audio and video devices. This media plate can be installed upright, sideways.
IMPORTANT INSTRUCTIONS:
This product is designed for retrofit work only because the old workbox cannot be attached to a stud.
WARNING:
Before installing this product, be sure the power is off by switching the circuit breaker to off or removing the fuse(s). Test the power to make sure
the power is off. Be sure to install the Media Plate with Duplex Receptacle in accordance with the National Electrical Code (NEC) and local codes.
Fig. 2
Fig. 3
Installation Instructions:
Fig. 1 Top view - shows needed space between the drywall and the studs. Receptacle side of the media plate must be 3” from the stud but no more than 5”
Fig. 2 Using the template supplied (see page 2 of instruction sheet), trace the opening needed. Using a drywall knife, cut a hole in the drywall the size of the
Fig. 3 Run the source of power to the included workbox.
Fig. 4 Using the supplied duplex receptacle, connect the hot line (black) wire to the brass colored terminal or screw and the neutral (white) wire to the silver
Fig. 5 Now use the four screws provided to secure the work box to the mounting studs on the backside of the of the media plate.
Fig. 6 Pull all video and audio cords through the recessed opening. Starting with the receptacle side of the media plate, slowing slide the plate into the
WARNING
DataComm Electronics’ products shall be installed and used only as indicated in DataComm Electronics’ product instruction sheets.
Instruction sheets are available online at www.datacommelectronics.com.
CAUTION
For shock protection, this device must be properly grounded.
Use copper wire only with this device.
(review picture carefully).
template. See Figure 1 before tracing your opening.
colored terminal or screw. Be sure to connect the grounding (green) or bare grounding wire to the green colored terminal screw. For shock protection,
this UR, UL recognized component receptacle must be properly grounded. Caution – use copper wire only with this receptacle. Once you have wired
the receptacle, screw the receptacle into the work box until the receptacle is firmly secured.
opening. Swing the opposite side of the plate into position until the entire media box is flush with the wall. Now screw down the screws with wings;
these wings fasten tightly against the back of the drywall. Switch on the circuit breaker to on or insert the fuse(s). Plug all necessary video and audio
cables. Install your flat panel TV mounting bracket per the flat panel TV bracket manufacturer’s instructions.
Tools Needed:
1. Drywall Saw
2. 6 Ft. Tape Measure
3. Pencil
4. Screwdriver
Fig. 1
Fig. 4 Fig. 5 Fig. 6
Page 1 of 2
12/21/10 Rev. 2
Loading...