Monoprice MHD Action Camera Board Mount, MHD Action Camera Board Mount 10162 User Manual
1
Mounting Clip Shoe
7
46" Nylon Mount Strap
2
1/4"-20 UNC Fixed Mount
8
140" Nylon Mounting Strap
3
Board Mount
9
Fitting Piece
4
Double Sided Adhesive Board
Pads
10
Double Sided Adhesive Fitting
Piece Pad
5
Security Strap Ring Plate
11
Single Sided Adhesive Fitting Piece
Pad
6
Double Sided Adhesive Ring
Plate Pad
MHD Action Camera Board Mount
Product ID: 10162
Features
Attach the camera to any type of board (surf, skate, ski, etc.)
Quick and easy mounting and removal of the MHD Action Camera
Package Contents
Please take an inventory of the package contents to ensure you have all the items
listed below. If anything is missing or damaged, please contact Monoprice Customer
Service for a replacement.
Preparing the Camera for Mounting
Prior to mounting the camera, attach the Security Strap and 1/4"-20 UNC Mounting
Clip to the camera according to the instructions included with the camera. Note that
the Security Strap and Mounting Clip are included with the camera.
Attaching the Camera Mount
1. Determine whether you will be using the Mounting Clip, with its quick
release option, or the Fixed Mount.
2. Loosen and remove the screw at the extreme end of the mounting arm.
3. Attach the Mounting Clip Shoe or Fixed Mount to the mounting arm using
the screw you removed in the previous step.
Attaching the Mount to a Board
There are two basic ways to attach the Board Mount to a board:
Using the adhesive pads
Using a mounting strap
The adhesive option is intended for more permanent mounting solution, while the
strap gives the flexibility of a more temporary mounting solution.
Adhesive Pad Mounting
To attach the Board Mount using Adhesive Pads, perform the following steps:
1. Remove the protective film from one side of a Double Sided Adhesive
Board Pad and attach it to the underside of the Board Mount.
2. Remove the protective film from the other side of the pad.
3. Position and orient the mount then press the mount firmly against the
board to attach the pad.
4. Remove the protective film from one side of a Double Sided Adhesive
Ring Plate Pad and attach it to the underside of the Security Strap Ring
Plate.
5. Remove the protective film from the other side of the pad.
6. Position and orient the Security Strap Ring Plate so that fits into the notch
on the base of the Board Mount.
Note: For best results, the Board Mount and Ring Plate should be attached at least 24
hours before it is to be used. This gives the adhesive time to set to ensure the mount
does not come loose.
Attaching the Strap to the Board Mount
The included nylon straps provide an alternate mounting solution. To attach the straps
to the Board Mount and prepare the assembly for attaching to a board, perform the
following steps:
1. Choose the strap length that will best fit your board.
2. Remove the two strap clips from the strap.
3. One each side of the Board Mount are three slots. Thread one end of the
strap up through the slot closest to the center, as
shown in the image to the right.
4. Look closely at the strap clip. Note that the clip
lock will only fully engage in one direction and that
the clip base is knurled on the other side. Thread
the strap down through the knurled side of the
strap clip from the top, as shown in the image to the right.
5. Thread the strap down through the middle slot
as shown in the image to the right.
6. Thread the strap up through the outer slot as
shown in the image to the right.
7. Pull the strap to remove any slack.
8. Repeat steps 3-7 on the other side of the Board
Mount.
The Board Mount assembly is now ready to attach to a board.
Attaching to a Board
1. Decide where you want to mount the camera on your board. Mark the
position on your board.
2. Remove the protective film from a Single Sided Adhesive Board Pad and
attach it to your board directly under the mounting location of the Board
Mount.
3. Remove the protective film from a Single Sided Adhesive Fitting Pad and
attach it to the underside of your board.
4. Thread one end of the strap up through the one of the slots on the Fitting
Piece then back to up through the locking side of the Strap Clip on the
Board Mount assembly.
5. Position the Board Mount assembly over the attached Board Pad and the
Fitting Piece over the Fitting Piece Pad on the opposite side. Remove
slack in the strap and lock the clip into place.
6. Repeat steps 4-5 for the other side of the strap.
7. The Board Mount assembly should now be somewhat loosely in place.
Pull the straps and mounting pieces to get everything in the perfect
position, then unlock one of the strap clips, pull the strap tight, and lock the
clip into place. Repeat this tightening and adjusting process until the Board
Mount is securely fixed to the board.
Final Adjustments
1. Once the Board Mount assembly is firmly attached to your board, slide the
camera Mounting Clip into the Mounting Clip Shoe.
2. Loosen the nut at the base of the mounting arm and the screws on the
mounting arm pivot points. Aim the camera as desired.
3. Tighten the nut and screws to lock the camera's position and orientation
into place.
Loading...