Page 1
INSTALLATION GUIDE
Flat Panel Mount
MF- 52
Support 32" to 52" Screens
Max Load Capacity: 125 lbs (57 kg)
VESA 100x100 / 100x200 / 200x200 / 400x500 compatible
Page 2
Installation Instructions
32”-52” UNIVERSAL FIXED WALL MOUNT
Important Notes
Model Name:MF-52
The32”-52”Universal Fixed Wall Mount supports LCD and
supports a maximum load of
57 kg(125 lbs).
The manufacturer does not accept responsibility for incorrect installation.
Component Checklist
Bits Bag
J
square spacer (x4)
MN
concrete anchor outside the hexagonal
M8X50(
x4)
M8x mm
35
M8x mm
16
M6x mm
35
M6x mm
16
mm
M5x35
M5x16mm
Wall Plate
TOOLS REQUIRED:
Power Drill
10mm or 6mm Drill Bit
Phillips Head Screw Driver
Spirit Level
13mm (
1
) Socket Wrench
2
/
or Shifter
monitor bracket-(BB)
Security Bracket
C
8.2X1.5X 16
iron spacer(x4)
L
19X 8.2X19.6
Spacer(x4)
Cross pan head screw
K
12.7X 6.0X12.7
Spacer(x4)
X70
M8
self-tapping screws(X4)
(x4 each)
(x4 each)
(x4 each)
(x4 each)
((xx4each)
4each)
I
H
G
F
E
D
Mounting the Wall Plate
Masonry Wall
Note:Ensure the Wall Plate
is mounted with the folded
tabs pointing upwards.
10mm(
outside the hexagonal
self-tapping screws
”) Hole
3/8
iron spacer
TIP:Use a spirit
level to ensure the
Wall Plate is
horizontal
concrete anchor
all Plate
W
Timber Stud Wall
Note:Ensure the Wall Plate
is mounted with the folded
tabs pointing upwards.
outside the hexagonal
self-tapping screws
10mm(
3/8
concrete anchor
iron spacer
”) Hole
all Plate
W
Page 3
Mounting the Display Brackets
Mounting
screw
square spacer
Adapter
Bracket
M6 & M8
Screw hole
M4 & M5
Screw Hole
NOTE:
*
When attaching the mounting
screws to the display,make sure
the direction of Brackets is correct
and ensure that both brackets
are vertically aligned.
Recessed Mounting Holes.
If the mounting holes are recessed
into the back of the display, use the
supplied spacers to pack the recessed
hole. If the mounting screw is M4
& M5 & M6,use the ¢12.7 x ¢ 6.0x 12 . 7
Spacer.If the mounting screw is M8,use
the ¢19x¢8.0x19.4 Spacer . Ensure
that the brackets are securely fixed to
the display.
Mounting
screw
square spacer
Bracket
Attaching the display to the wall plate
Note: This procedure will
require two persons
With the Brackets attached
to the display, lift the
display and hook the
brackets onto the Wall
Plate as shown.
Note: For demonstration purposes, the wall
has been omitted from the above images.
Security Option
Note: For demonstration purposes, the wall
has been omitted from the above images.
Back
of Display
Recessed
ole
H
Spacer
Back plate
Padlock
Security
Bracket
For additional security, it is suggested that the left and
right Security Brackets be inserted and a Padlock attached
through each Security Bracket and the Wall Plate as shown.
The two Padlocks (not supplied) should have a shackle
diameter no larger than 5mm (
”).
/
3
16
Loading...