Page 1
Monoprice Adjustable Tilt Swivel Plat Panel Wall Mount
Model: RLB-110S-ME(S)-R (PID#8589)
VESA Compliant up to 450x300
Max Weight: 130lbs
InstallationInstruction
English
UNPACKING INSTRUCTIONS
!
Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
!
Check package contents against the Supplied Parts List in the next page to assure that all components were received
undamaged. Do not use damaged or defective parts.
!
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before beginning the installation, and carefully
follow all instructions contained herein. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you:
!
If you don't understand these directions or have any doubts about the safety of the installation.
!
If you are uncertain about the nature of your wall, consult a qualified installation contractor.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby
disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of
this product.
CAUTION!
This TV mount must be securely attached to the vertical wall. If the mount
!
WARNING
is not properly installed it may fall, resulting in possible injury and/or
damage.
Tools Required
5/32"(4mm) Drill Bit
Phillips Screwdriver
3/8"(10mm) Masonry Bit
Stud Finder
Wrench or Socket Set
Carpenter's Level
Note: The mounting components and hardware supplied in this package are not designed for installations to
walls with steel studs or to cinder block walls. If the hardware you need for your installation is not included,
please consult your local hardware store for proper mounting hardware for the application.
1
Page 2
Supplied Parts List
(1)Wall Plate-a (1)Right Monitor Bracket-c
(4)M4x12 Bolt-d (4)M5x12 Bolt-e (4)M6x12 Bolt-f (4)M8x16 Bolt-g
(4)M4x30 Bolt-h (4)M5x30 Bolt-i (4)M6x35 Bolt-j (4)M8x40 Bolt-k
(4)M4 Lock Washer-l (4)M5 Lock Washer-m (4)M6 Lock Washer-n (4)M8 Lock Washer-o
(1)Left Monitor Bracket-b
(4)M4/M5 Space-p (4)M6/M8 Space-q (8)M4/M5 Washer-r (4)M6/M8 Washer-s
(6)M8x90 Lag Bolt-t (6)Lag Bolt Washer-u
(6)M10x80 Concrete Anchor-v
Pls install the Plastic Knob on the Monitor
Bracket(b,c) as left diagram before do the
next step. Pls note the two knobs should be
installed in the opposite way on the two
monitor brackets.
2
Page 3
Step 1A
First of all, make sure the diameter of the Bolt(d,e,f,g) your TV requires. Once you have determined the correct diameter,
please see the relative diagram as below. You will thread the Bolt the correct Lock Washer(l,m,n,o) and
Washer(r,s). Please make sure the Monitor Brackets(b,c) are vertically centered and level with each other.
Mounting the Monitor Brackets to a TV with Flat Back
into the TV using
M4 Diameter Bolt M6 Diameter Bolt
Step 1B
b
d
l
r
Diagram 1A
M5 Diameter Bolt M8 Diameter Bolt
e
m
r
f
n
s
g
o
s
c
Mounting the Monitor Brackets to a TV with Curved Back
First of all, Once you have determined the correct diameter,
please see the relative diagram as below. You will thread the Bolt the correct Lock Washer(l,m,n,o),
Washer(r,s) and spacer(p,q). For the M4 or M5 diameter bolt, you will need another M4/M5 Washer between the Monitor
Bracket and the Spacer. Please make sure the Monitor Brackets are vertically centered and level with each other.
make sure the diameter of the Bolt(h,i,j,k) your TV requires.
into the TV using
h
l
r
M5 Diameter Bolt M8 Diameter Bolt
i
m
r
r
p
r
p
Diagram 1B
b
M6 Diameter BoltM4 Diameter Bolt
j
n
s
s
q
k
o
s
s
c
q
3
Page 4
Step 2
Brick, Solid Concrete mounting:
Use the Wall Plate(a) as a template to mark 6 hole locations on the wall. Three in the top row of slots and three more in the
bottom row. Make sure these holes are level and there is at least 6"(150mm) distance between any two holes. Pre-Drill
these holes with a 3/8"(10mm) masonry bit to at least 3"(75mm) in depth. Insert a Concrete Anchor(v) into each of these
holes. Make sure the anchor is seated completely flush with the concrete surface even if there is a layer of drywall or other
material in front. Attach the Wall Plate to the wall using 6pcs Lag Bolts(t) and 6pcs Lag Bolt Washers(u), shown in Diagram
2A.
Wood Stud mounting:
The Wall Plate(a) Use a stud finder to locate two
adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown in Diagram 2B. Pre-drill
a 3"(75mm) deep hole at the desired height in each stud using a 5/32"(4mm) drill bit. Make sure these holes are in the
center area of the studs and level with each other. Use the Wall Plate as a template to mark the location of the second hole
in each stud. Drill 3"(75mm) deep holes using the 5/32"(4mm) drill bit in the marked locations. Attach the Wall Plate to the
wall using the 4pcs Lag Bolts(t) and 4pcs Lag Bolt Washers(u).
Mounting the Wall Plate to the Wall
must be mounted to two wood studs at least 16" (406mm) apart.
Diagram 2BDiagram 2A
u
t
a
Stud Finder
16 inch
16 inch
Step 3
WarningSomeTVs mayrequire twopeopletoliftWe arenotresponsibleforpersonalinjuryorproductdamage: ! .
First hook the Monitor Brackets(b,c) over the top of the wall Plate(a), then let the bottom of the Monitor Brackets rotate to
the bottom of the Wall Plate as shown in the Diagram 3A. Use the screwdriver to tighten the safety bolts. Then the Monitor
Bracket will sit behind the bottom tab on the Wall Plate as shown in the Diagram 3B.
Attaching Monitor to Wall Plate and Adding the Safety Bolts
Diagram 3A
Diagram 3B
b,c
16 inch
Safety bolt
b,c
a
wall
a
wall
4
Page 5
Step 4
You can re-level the mount after the mount has been installed on the wall. Leveling is achieved by rotating the front plate
the TV sits on. Needn’t to loose the 5 bolts on the front plate, just hold the TV and do the adjustment. See Diagram 4 below.
Levelling Mount
Diagram 4
WARNING
UsetwopeopletoliftandpositiontheTVontotheWallPlate .
Thanks for choosing our products, enjoy the using.
5
Loading...