Monoprice 8099 User Manual

Pitching angle adjustment

• Tighten the screws till the displ ay angle ca n be fixed, t hen push or p ull from to p or bottom o f screen to a djust

the display to the desired angle.

• The pitching angle can be adjusted between -20° ~ +20°, swivel: ±90°, pivot: ±10°, as shown in fig.4.1.

±9 0°

+2 0°

-20°

±9 0°

+1 0°-10°

INSTALLATION INSTRUCTIONS

M-J

Maintenance

Once you h ave mou nted th e brack et and the fla t scree n, chec k that th ey are sufficie ntly se cure an d safe to u se. You should chec k wheth er scre ws are fi xed well each two mon ths. If y ou have a ny doub ts regardi ng the instal latio n, plea se cons ult our reta iler or s ervic e depar tment for detail.

fig. 4. 1

Pitc hing an gle:

-20° ~ +20° Swiv el: ±90°

20kg

(44lbs)

MAX

LCD Wall Mount

Max Load Capac it y: 2 0k g( 44 lb s)

Model: MDA03-222

NOTE: Read e nti re in str uction sheet b efo re yo u sta rt installat ion a nd as sem bly.

WARNING

• Do not begin the installation of the product before you have read and understood the instructions and warnings contained in this installation sheet. If you have any question regarding any of the instruction or warning, Please contact your local distributor.

• Please refer to installation guide recommendation for required distance from wall to avoid risk of property damage.

• This product should only be installed by someone of good mechanical aptitude, with experience and basic building, and fully understands.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Never exceed the maximum load capacity.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge” stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Componen t Che ckl ist

IMPORTAN T: Ens ur e yo u ha ve received a ll p ar ts a ga in st t he c om po ne nt c he ck li st p rior to insta ll in g. I f an y pa rt s

are m issing or fau lt y, tel ephone the sp ec ia l fr an ch is er f or a r ep la ce me nt .

Package M

M4x1 4

(x4) M5x1 4 (x 4)

M-A

ø ø10

D4 ( 4.5x )

wash er

M-E

(x4)

M-B

D (ø .5xø )

5 5 1 2

(x4)

wash er

M-F

M6x1 4 (x 4)

M-C

D6 (ø6 .3 xø )

wash er

M-G

(x4)

M8x1 5 (x 4)

M-D

D8 (ø8 .3 xø )

wash er

M-H

(x4)

• Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.

• This products intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

ø13. 5x ø5.5x 3. 2 (x4)

M-I

3mm allen key (x1)

Package W

ST 5. 5x5 0 (x3)

lag bo lt conc re te anch or

W-A

Tools required

Phillips Head Screw driver(200mm length exclude the handle)

Electric drill and 8mm masonry bit for concrete wall installation

Marking Pen

Hammer

M-J

W-B

(x3)

+ 2 hidden pages