3G USB Modem Compatibility List
Network
CDMA2000
EVDO
TD-SCDMA
HSPA
WCDMA
Mobile
USB 3G Modem
EC189
EC169
EC1260
AC2726
AC2736
AC2746
AC580
AC560
MF637U
DWM-162-U5
Anydata
St802
Rw206
EVDO
SRT-E800
Ev2000
EVDO E1916
1XEVDO Modem
WOO ED6000
More than 20 kinds
of EVDO
ET128
MU350
MU351
AirCard901
E1552
E1750
E169G
E156G
E172
E220
E270
E272
K3715
MF622
U302
OVATION: MC930D
HSDP: 621B
V818U
USB Connect Mercury
Nokia N95
Brand
Huawei
Huawei
Huawei
Huawei
ZTE
ZTE
ZTE
ZTE
ZTE
D-LINK
Anydata
Sentar
R-WAY
R-WAY
SRT
NEW-NET
Vtion Tech.
SR Wireless
WOO
unofficial Brands
Huawei
ZTE
ZTE
Datang
Huawei
Huawei
Huawei
Huawei
Huawei
Huawei
Huawei
Huawei
Huawei
ZTE
Sierra Wireless
O2
Telit
Unknow
AT&T
Nokia
Testing result
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
Wireless 3G-N1
Broadband Router
Quick Installation Guide(Q.I.G.)
REV.1. 0
*
Compatiability testing list is just for reference. More of the
models can be supported.
* The compatibility list is updating. Please check with our website!
Copyright Notice
Copyright Incorporated 2010. All rights reserved.
Disclaimer
Incorporated shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
Incorporated reserves the right to change product specifications without
notice. Information in this document may change without notice.
Trademarks
Microsoft, Windows XP, Windows VISTA and Windows 7 are registered
trademarks of the Microsoft Corporation. All other brand and product
names mentioned herein may be registered trademarks of their respective
owners.
Customers should ensure that their use of this product does not infringe
upon any patent rights. Trademarks mentioned in this publication are sued
for identification purposes only and are properties of their respective
companies.
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
CONTENTS
Introduction
Wireless-N Router Panel
Getting Started
Configuring via Web Browser
Setup the router mode
LAN Settings
Connect to Internet (3G Dialup)
Connect to Internet (Gateway)
WAN MAC Clone
Dynamic DNS
Wireless Base Configuration
Wireless Security Configuration
Router Administrator Setup
Change management password
Settings Backup and Restore
Firmware Upgrade
Restore to Factory Default
01
02
03
05
07
08
09
10
12
13
14
15
17
17
18
19
20
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Introduction：
The Wireless-N 3G Router is a combined wired/wireless network
connection device designed specifically for small business, office, and
home office networking requirements. It complies with the IEEE 802.11n
(Draft 2.0) standard. It adopts MIMO as well as SST technologies. It also
works well with other 11b/g and 11n protocol wireless products.
· Create instant WiFi hotspots at any location where you have 3G
connection
· Supports 3G USB cellular modems, supports
SCDMA, HSPA/WCDMA
· Can also work with your existing DSL or cable modem
Package Contents
Before you starting to use this router, please check if there's anything
missing in the package, and contact your dealer of purchase to claim for
missing items:
· 1 x Wireless-N 3G Router
· 1 x Quick installation Guide
· 1 x Power adapter
· 1 x RJ-45 Networking Cable
CDMA2000 EVDO, TD-
Wireless-N Router Panel
LAN/WAN Port
Power connector
Connects to 3G USB modem
Router Mode LED
Wireless LED
LAN / WAN LED
Power LED
WPS/RESET Button :
Press this button 1 Second for WPS
encryption link, the WPS LED will
flashing while the button press.
Press this button 5 Second for Reset the
router to factory default settings (clear all
settings).
MODE Button :
Factory default settings: Gateway
Press this button for Gateway / AP /
Station / 3G switch, easy to switch
wireless operation mode via this button.
01
02
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Getting Started
Setting up a Wireless Infrastructure Network
For a typical wireless setup at home (as shown above), please do the
following:
1. You will need broadband Internet access (a 3G USB Modem or Cable,
DSL-subscriber line into your home or office).
2. Consult with your 3G, Cable or DSL provider for proper installation of the
modem.
3. Connect the 3G USB Modem, Cable or DSL modem to the Wireless 3G N1 Router
4. Adding computers to the Wireless 3G-N1 Router.
Adding computers to the Wireless 3G-N1 Router
1. Log on to the computer.
2. Open Connect to a Network by right-clicking the network icon ( or )
in the notification area.
3. Choose the wireless network from the list that appears, and then click
Connect.
4. Type the network security key or passphrase if you are asked to do so,
and then click OK.
You'll see a confirmation message when you are connected to the
network.
5. To confirm that you added the computer, do the following:
Open Network by clicking the Start button ,and then clicking Control
Panel. In the search box, type network, and then, under Network and
Sharing Center, click View network computers and devices.
You should see icons for the computer you added and for the other
computers and devices that are part of the network.
Note : If you don't see icons in the Network folder, then network discovery
and file sharing might be turned off. For more information:
http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-to-a-network
http://windows.microsoft.com/en-US/windows7/Setting-up-a-wireless-network
http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network
03
04
Configuring via Web Browser
Open web browser and type http://192.168.0.1 in the browser's address
box. This number is the default IP address for this device.
The login screen below will appear. Enter the “User Name” and “Password”
and click “OK” to login.
The default User name is “admin” and the Password is “admin”,
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
After successfully login, the following Router Summary will be displayed on
your web browser:
05
06
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Setup the router mode
To Setup the router mode, please follow the following instructions:
Please click “Mode” located at the web management interface, the
following message will be displayed on your web browser:
Ø 3G Wireless Router Mode
Wireless and LAN port connect to local network; the 3G USB modem
connect to internet.
Ø Wireless Router Mode (Gateway)
Wireless connect to local network, The LAN port connect to internet.
Ø Wireless AP Mode
Wireless work for access point, LAN port connects to local network.
Ø Wireless Client Mode (Station)
LAN port connect PC or local network, Wireless work for a WAN port
connect to other wireless AP or router.
Click the APPLY button to Change your Router Mode.
LAN Settings
Please click “LANSetup” located at the web management interface, the
following message will be displayed on your web browser:
IP Address:
Subnet Mask:
DHCP Type:
Note:
1) If you change the IP Address of LAN, you must use the new IP Address
to login the Router.
2) If the new LAN IP Address you set is not in the same subnet, the IP
Address pool of the DHCP server will change accordingly at the same
time，while the Virtual Server and DMZ Host will not take effect until
they are re-configured.
Enter the IP address of your Router or reset it in
dotted-decimal notation Wireless N Router (factory
default: 192.168.0.1).
An address code that determines the size of the
network. Normally use 255.255.255.0 as the subnet
mask.
Enable or Disable
07
08
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Connect to Internet (3G USB Modem)
Please click “Mode” located at the web management interface, select 3G
Wireless Router Mode. The Router will restart.
After Please click “3G→Setup” located at the web management interface,
You can configure parameters for 3G function on the screen below.
To use the 3G function, you should first insert your USB modem on the
USB port of the Router.
Interface description
3G ISP
APN
Pin Code
Dialup number
Username /
Password
Auto Dial-up
Click the APPLY button to connect to your 3G network.
Select 3G ,DWR/PWR series only have 3G dialup mode
Enter the APN (Access Point Name) provided by your ISP.
Enter the Pin Code provided by your ISP.
Enter the Dial Number provided by your ISP.
Enter the Username and Password provided by your ISP.
These fields are case-sensitive.
Connect automatically after the Router is disconnected. To
use this option, click the radio button.
Connect to Internet (Gateway)
Please click “Mode” located at the web management interface, select
Wireless Router Mode(Gateway). The Router will reboot.
After Please click “WAN→Setup” located at the web management
interface, Following example is for “PPPoE(ADSL)” WAN setting.
Enter the “PPPoE Username” and “PPPoE Password” that ISP provided
and leave the others. (The “Service Name” can be blank)
Click “Apply” button to save the settings then reboot the router.
After reboot, your router is now ready for Internet connection.
09
10
WAN MAC Clone
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway
and DNS setting, select 'STATIC (fixed IP)'.
Enter the IP address / Subnet Mask / Default Gateway / MTU / Primary /
Secondary DNS in dotted-decimalnotation provided by your ISP.
If your ISP provides the DHCP service, please choose 'DHCP(Auto
config)', and the Router will automatically get IP parameters from your
ISP.
This page displays the WAN IP parameters assigned dynamically by your
ISP, including IP address, Subnet Mask, Default Gateway, etc.
Please click “WAN -> MAC-Clone” located at the web management
interface, the following message will be displayed on your web browser:
Some ISPs require that you register the MAC Address of your adapter,
which is connected to your cable/DSL Modem during installation. If your
ISP requires MAC register.
If your PC's MAC address is proper MAC address, click the "Use the MAC
Address of the PC" button and your PC's MAC address will fill in the
"WAN MAC Address" field.
Or else, type the MAC Address into the "WAN MAC Address" field. The
format for the MAC Address is XX-XX-XX-XX-XX-XX.
Then click the "APPLY" button. It will take effect after rebooting.
11
12
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Dynamic DNS
Please click “WAN (3G) -> DDNS” located at the web management
interface, the following message will be displayed on your web browser:
The Router offers the DDNS (Dynamic Domain Name System) feature,
which allows the hosting of a website, FTP server, or e-mail server with a
fixed domain name (named by yourself) and a dynamic IP address, and
then your friends can connect to your server by entering your domain
name no matter what your IP address is. Before using this feature, you
need to sign up for DDNS service providers. The Dynamic DNS client
service provider will give you a password or key.
To set up for DDNS, follow these instructions:
1. DDNS: Enabled
2. Type the User Name for your DDNS account.
3. Type the Password for your DDNS account.
4. Type the Domain Name you received from dynamic DNS service
provider.
5. Click the APPLY button to log in the DDNS service.
Wireless Base Configuration
Please click “Wireless -> Basic” located at the web management
interface, the following message will be displayed on your web browser:
You could configure the minimum number of Wireless settings for
communication, such as Network Name (SSID) and Channel. The Access
Point can be set simply with only the minimum setting items.
Wireless Enabled
802.11 Mode:
SSID:
Do Not Broadcast
SSID:
Channel
Wireless On/Off
Supports 1b/g mixed, 802.11b, 802.11g and 1b/g/n
mixed modes.
Main Service Set Identifier. It's the "name" of your
wireless network.
Select “enable” to enable the device's SSID to be
visible by wireless clients
This field determines which operating frequency will
be used. The default channel is set to Auto, so the
AP will choose the best channel automatically. It is
not necessary to change the wireless channel unless
you notice interference problems with another
nearby access point.
13
14
Wireless Security Configuration
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Please click “Wireless-> Security” located at the web management
interface, the following message will be displayed on your web browser:
Setup the wireless security and encryption to prevent from unauthorized
access and monitoring. Supports 64/128-bit WEP, WPA, WPA2 encryption
methods.
When you finish, click 'APPLY'.
Please click “Wireless-> WPS” located at the web management interface,
the following message will be displayed on your web browser:
you can establish a wireless connection between wireless adapter and
Router using either Push Button Configuration (PBC) method or PIN
method.
WPS: Enable / Disable
WPS Mode →PIN: If the new device supports Wi-Fi Protected Setup and
the PIN method, you can add it to the network by PIN.
WPS Mode →PBC: If the wireless adapter supports Wi-Fi Protected Setup
and the Push Button Configuration (PBC)
Step 1: Press the WPS button on the Router.
Step 2: Press and hold the WPS button of the adapter directly for 2 or 3
seconds.
Step 3: Wait for a while until the next screen appears. Click Finish to
complete the WPS configuration.
15
16
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Router Administrator Setup
Change management password
Default password of Wireless Router is “admin”, and it's displayed on the
login prompt when accessed from web browser. There's a security risk if
you don't change the default password, since everyone can see it. This is
very important when you have wireless function enabled.
To change password, please follow the following instructions:
Please click 'Admin-> Password' menu on the web management
interface, the following message will be displayed on your web browser:
When you finish, click 'APPLY'; If you want to keep original password
unchanged, click 'CANCEL'.
Settings Backup and Restore
You can backup all Setting of this router to a file, so you can make several
copied of router configuration for security reason.
To backup or restore router setting, please follow the following instructions:
Please click click 'Admin-> Backup&Restore' located at the web
management interface, then the following message will be displayed on
your web browser:
Press 'Backup…' button, and you'll be prompted to
Backup Settings :
Restore Settings :
download the configuration as a file, default filename is
'RxRouter.cfg', you can please save it as another
filename for different versions, and keep it in a safe
place.
Press 'Browse…' to pick a previously-saved
configuration file from your computer, and then click
'Restore…' to transfer the configuration file to router.
After the configuration is uploaded, the router's
configuration will be replaced by the file you just
uploaded.
17
18
Wireles s 3G -N1 Bro ad band Rout erWireles s 3G -N1 Bro ad band Rout er
Firmware Upgrade
The system software used by this router is called as 'firmware', just like
any applications on your computer, when you replace the old application
with a new one, your computer will be equipped with new function. You can
also use this firmware upgrade function to add new functions to your
router, even fix the bugs of this router.
To upgrade firmware, please follow the following instructions:
Please click 'Admin->Firmware-Upgrade' located at the web
management interface, then the following message will be displayed on
your web browser:
Click 'Browse' button first, you'll be prompted to provide the filename of
firmware upgrade file. Please download the latest firmware file from our
website, and use it to upgrade your router.
After a firmware upgrade file is selected, click 'UPGRADE' button, and the
router will start firmware upgrade procedure automatically. The procedure
may take several minutes, please be patient.
Restore to Factory Default
If you think the network performance is bad, or you found the behavior of
the router is strange, you can perform a router reset; sometime it will solve
the problem.
To do so, please click 'Admin-> Factory-Defaults' located at the web
management interface, then the following message will be displayed on
your web browser:
Load Factory Defaults: Click this 'RESTORE…' button to remove all
settings you made, and restore the configuration of this router back to
factory default settings
NOTE: Never interrupt the upgrade procedure by closing the web browser
or physically disconnect your computer from router. If the firmware you
uploaded is corrupt, the firmware upgrade will fail, and you may have to
return this router to the dealer of purchase to ask for help. (Warranty voids
if you interrupted the upgrade procedure).
19
20
Loading...