Monoprice 7469 User Manual

Locking Adapter Brackets
• First, pull the outside safety straps on the adapter brackets, and then slowly allow display to return to the wall. Finally loosen the safety straps and lock the adapter brackets.
INSTALLATION INSTRUCTIONS
fig. 4.1
The saf et y strap s can be fo ld ed and keep in b ac k of the di splay.
fig. 4.2
Important: Make sure the TV is correctly hooked and the safety locking bars are locked safely.
Maintenance
• Once you have mounted the bracket and the flat screen, check that they are sufficiently secure and safe to use,
• You should regularly check that the screws and hardware are secure to your wall every two months for safety.
• If you have any doubts regarding the installation, please consult our retailer or service department for further details.
7
50kg
(110lbs)
MAX
LED WALL MOUNT
Model: MED-026
Max Loa d Cap aci ty : 50k g(11 0lbs)
NOTE: Read entire instruction sheet before you start installtion and assembly.
WARNING
• Do not begin the installation of the product, until you have read and understood the instructions and warnings provided in the installation manual. If you have any questions regarding the warnings and instructions, please contact your local supplier.
• Please refer to the manufacturers installation guide for proper wall recommendation distance to avoid the risk of property damage.
Component Checklist
IMPORTANT: Ple ase e ns ure a ll pa rts lis ted a re incl ude d prior t o you r insta lla tion. I f any p art s ar e mis sin g or
fau lt y, ple ase c ont act the s pec ial fra nch iser fo r a rep lacem ent .
wall pl at e
A
(x1)
(x2)Adapt er b racke t
B
• This product should only be installed by someone of good mechanical aptitude, with experience and basic building, and fully understands.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge” stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.
• This product is intended for indoor use only. The use of this product other then indoors could lead to product failure and personal injury,
Suppo rt ing spa cer (x1 )
Package M
M4x14
(x4)
M-A
M6x14 ( x4 )
M-E
Ø Ø (x )12x 5.5 Washe r 2
M-I
Package W
M6x55 (x )
lag bol t 6
W-A
C
M4x30
(x4)
M-B
M6x30 ( x4 )
M-F
Ø Ø (x2)16x 8.2 Washe r
M-J
concr et e ancho r 6
Suppo rt ing spa cer (x1 )
M5x14 ( x4 )
M-C
M8x14 ( x4 )
Ø ( 4)12xØ6 x1 3 x
W-B
D
M-G
M-K
(x )
M5x30 ( x4 )
M-D
(x4)
M8x30
M-H
Ø17.5 xØ 8x20
Ø Ø (x )16x 6.2 Washe r 6
M-L
W-C
(x4)
Tools required
Phillips Head Screw driver(200mm length exclude the handle)
·
M6 Socket and Wrench
·
·
Electric drill and 10mm masonry bit for concrete wall installation
·
Marking Pen
·
Hammer
21
Loading...
+ 2 hidden pages