Monoprice 6645 User Manual

DIMENSIONS

153.0

EXTERNALLY ADJUSTABLE DAY&NIGHT VARI-FOCAL IR BULLET CAMERA

EXTERNALLY ADJUSTABLE DAY&NIGHT

VARI-FOCAL IR BULLET CAMERA

Ø77.5

88.0

[ IR-LED 42pcs ]

FUNCTION & INSTALLATION

∞

[

DC LEVEL

]

CAMERAVARI-FOCALIR

128.7

[ BODY & SUN-SHIELD ]

[

H L

85.0

38.8

[ BRACKET ]

]

95.0

77mm (Ø) × 128mm (L)) ×

Max. 90% RH

-10℃ ~ +50℃-

Normal: 240mA, Max: 680mA / DC12V (IR LED On)

Normal: 5.3VA, Max: 10.5VA / AC24V (IR LED On)

Normal: 200mA, Max: 500mA / DC12V (IR LED On)

Model

AC24V / DC12V

DC12V Model

AC24V±10%, DC12V±10%± ±

(optional 9.0~22mm F1.8 Lens)

3.8~9.5mm Vari -Focal, DC Auto Iris F1.2 Day & Night Lens

VBS 1.0 Vp-p (75Ω Load)Video Output

ATW / AWC selectable

0Lux (IR LED On)

Internal

More than 48dB (AGC Off)

1/50 sec.1/60 sec.

550/480TV-Lines (Color) , 580/510TV Lines (B/W)- -

15.625KHz (H), 50Hz (V)

625 Lines 2:1 InterlaceScanning System

15.734KHz (H), 59.94Hz (V)

525 Lines 2:1 Interlace

752H × 582V (440K pixels)×768H × 494V (380K pixels) ×

1/3" Interline transfer type color CCD (SONY)

PALNTSC ITEM

(*) Must use regulated & specified power supply.

Dimensions

Operational Humidity

Operating Temp.

 Function

① Protective Film over Front Glass - Remove this film before operating the Camera. ② Focus/Zoom Lever Bolt Screws - Used to fix the Focus/Zoom ring to the lens internally.

Be careful not to lose this small bolt screws which need not be touched other than by a service technician.

③ Focus/Zoom Ring Fixing Screws - Used to fix the Focus/Zoom Ring at the desired position after adjusting the lens

angle and focus setting as described below.

Consumption Power

④ Focus and Zoom Ring - These two rings are used to accurately adjust the viewing angle and to sharply focus all objects

within the lens field of view.

- Loosen the fixing screws(③) of the Zoom and Focus ring.

Power Supply(*)

Lens

Video Output

White Balance

Min. Illumination

Sync. System

S/N Ratio

Shutter Speed

Resolution

Scanning Frequency

in. (Option: 9.0-22mm F1.8 Lens)

Scanning System

Effective Pixels

Image Sensor

ITEM

• Waterproof Outdoor Installation (IP66)

• AC24V/DC12V Dual Power Available

• 2Glasses Adapted Optional

BLC and White Balance

• Dip Switch control of Day & Night time delay, Flickerless

• Externally Adjustable DC Iris Level

• CDS Auto Switching IR LED Control (42 IR LEDs)

• Color & B/W Auto Switchable by Photocell and Sensitivity

Lens Built -

• Filter Changeable Vari-Focal DC Auto Iris 3.8~9.5mm F1.2

• Externally Adjustable Focal Length & Focus by Rings

(Option: EXview HAD CCD)

• SONY 1/3” Super HAD High-resolution Color CCD

FEATURES SPECIFICATIONS

i) To widen the viewing angle turn the “Zoom Ring” to “W” (Wide). ii) To obtain a closer view turn this ring to “T” (Tele).

- After adjustment of the viewing angle then adjust the “Focus Ring” between “N” (Near) or “∞” (Far) until the sharpest

- Then tighten the fixing screws(③) on each ring.

- After tightening you should check that angle and focus is still accurate.

⑤ DC Level Volume Screw Cap

- Loosen the DC level volume screw cap on the camera body. i) For a brighter screen turn the DC level volume slowly toward “H” (counter-clockwise), ii) For a darker screen turn it toward “L” (clockwise) with a driver.

⑥ Bracket - Used to install the camera to the desired location.

Installation Method

Bracket & Camera Mounting

- Install the Mounting Bracket at the desired location.

Connecting to Monitor and Power

- Set the impedance switch to the 75

- Adaptor: DC12V / 1A regulated Power Supply (DC12V Model) AC24V / 800mA or DC12V / 1A (AC24V / DC12V Model

☞ Note * Be sure to connect power after all the installation is done.

* Do not use power sources other than that specified.

Sun-Shield Mounting

- After adjusting view angle, cap over the camera with the sun

standard position unless other equipment is looped out of the monitor.

shield and fix it to the camera with the sun

-shield bolt.

focus is achieved.