Monoprice 6515 User Manual

Download

Page 1

INSTALLATION GUIDE

Flat Panel Arm Mount

MHA-1

Support 24" to 37" Screens

Max Load Capacity: 80 lbs (36 kg)

VESA 200x200 compatible

Page 2

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

 Be sure to read this entire manual thoroughly and you fully understand all the instructions and warning before attempting to begin your installation.

 This product should only be installed by someone who has a basic knowledge of buiding construction,in stallations

and fully understands these instructions.

 Make sure that the supporting surface will safely support the combined load of the mount, the display and all attached hardware and components.

 This wall bracket will only support flat panel displays(LCD,Plasma).The maximum load capacity is 80 pounds.

 If mounting to a wall of wood stud construction, be sure that mounting bolts are anchored to the center of the

studs.

 Always have someone assist you to lift and position your equipment.

 Tighten screws and bolts firmly, but do not over tighten. Over tightening can damage the items and greatly reduce their ability to hold. Please refer to suggested torque values where applicable in these instructions.

Tools Needed for Assembly

 stud finder ("edge to edge" stud finder is recommended)

 phillips screwdriver

 pencil

 drill

 3/16"(4mm) drill bit for wood studs, 1/4"(6mm)( drill bit for concrete  level

 tape measure

Table of Contents

Parts List .......................................................................................................................................................................... 3

Installation to Single Wood Stud Wall ................................................................................................................................... 4

Installation to Solid Concrete and Cinder Block .................................................................................................................... 5

Attaching mount (AA) to Screen with VESA

Cable Management ............................................................................................................................................................. 8

Mounting Patterns

.................................................................................... 6,7

2 of 8

Page 3

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

Parts List

Description

B C D

E F

G H

philips pan head screw philips pan head screw philips pan head screw philips pan head screw philips pan head screw philips pan head screw spacer

concrete anchor /

corss slotted head screw

4 4 4 4 4 4

2 2

M4x0.7mmx10 M4x0.7mmx20 M5x15 M5x30 M6x1x12mm M6x1x30mm

Ø12.7xØ6.0x12.7

M6x50

M6x60

mount(AA)

3 of 8

Page 4

Installation to Single Wood Stud Wall

WARNING

 Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

 Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

 Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highly recommended.

 Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers

are responsible to provide hardware for other types of mounting situations.

Using a stud finder, locate and mark the edges of the wood stud. Use of an edge to edge stud finder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use AA as template to mark center of holes along the vertical line.

to wall using

two M6 X 60 hexagonal screws (

STUD

Drill three 1/8" (4 mm) dia. pilot holes 2" (50 mm) deep. Attach AA

) as shown in fig. A.2. Level plate, then tighten all fasteners.

fig. A.1

STUD

fig. A.2

4 of 8

Page 5

Installation to Solid Concrete or Cinder Block

WARNING

 When installing the wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

 Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

 Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

Use wall plate (AA) as template to mark mounting holes.

Drill three 1/4" (6 mm) dia. holes 2" (70 mm) deep as

shown in fig. B.1. Insert concerte anchor ( wall as shown (right). Place wall plate over anchors and

secure with M6x 60 cross slotted head screw (

fasteners.

) in holes flush with

WARNING

 Tighten hex head bolts

is firmly attached,but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

so that wall arm assembly

WARNING

 Always attach concrete anchors directl to load-

bearing concrete.

 Never attach concrete anchors to concrete covered

with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer.

Drill holes and insert anchors (F).

concrete surface

Place wall plate (D) over anchors (F) and secure with screws (E).

Tighten all fasteners.

solid concrete

cinde block

CUTAWAY VIEW

wall plate

plaster/ dry wall

INCORRECT

concrete

wall plate

plaster/ dry wall

CORRECT

concrete

fig. B.1

5 of 8

Page 6

Attaching AA to Screen with VESA® Mounting Pattern

Choose hole pattern as shown in detail 3 for VESA mounting pattern. Begin with the shortest length screw, hand thread

through adapter plate into screen as shown in detail 4. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the fastener pack. Repeat for remaining mounting holes. Securely tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

Mounting Patterns

VESA

200 x 200

ADAPTER

PLATE

SCREE

VESA

200 x 100

VESA

NOTE: For screens with a hole

pattern in a pocket,

spacers go between adapter plate and screen.

VESA

100 x 100 VESA® 75 x 75

DETAIL 3

200 x 100 VESA® 100 x 100

DETAIL 4

6 of 8

Page 7

For Flat Back Screen

C.1

fig C.1.1 fig C.1.2

SCREEN

SCREW

SCREEN

SPACER

Front Plate Front Plate

Select the small,medium,large or extra large screws from the screw package .Fastener pack then attach screen brackets(AA) to screen following figure C.1.1 or C.1.2 on page 7.

C.2

After the locked front plate is hanging on the wall panel , use a M4x12 philips pan head to fix these two parts.

Be careful when you operate this bracket,or you may damage your screen.

SCREW

WARNING

Do

not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen.

CAUTION

 Do not tighten screws with excessive force.

Overtightening can cause damage to mount.

fig.C.2.1

7 of 8

Page 8

Adjust tension knob on side of mount as shown infig.

D.1to desired tension to balance your screen size and weight. The tension knob, without changing the bracket tension, can be pulled out, away from the bracket and turned independently of the knob post for readjustment as shown in Push or pull from top or bottom of screen to adjust tilt as shown. The tilt can be adjusted to a maximum of -5° forward or +15°backward.

fig.D.2.

CAUTION

 Be careful not to pinch fingers when opening and

closing mount from the wall.

fig. D.2

fig. D.1

Cable Management

Note: Make sure cords have enough slack to allow

full movement of the arm. Route cords inside

arm slots of

in fig.E.1.

has been omitted from the image.

wall arm assembly (AA) as shown

For demonstration purposes, the wall

fig.E.1

WARNING

 Do not remove or loosen screw while the mount is in use. Doing so may cause the

8 of 8

screen to fall.