Monoprice 5916 User Manual

ASSEMBLY INSTRUCTIONS

FOR FIXED FLAT PANEL WALL MOUNT

This product is designed to mount flat panel televisions weighing up to 75kgs to a vertical firm wall. Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts. Improper installation may cause damage or serious injury. Note: The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The supplied hardware is not for steel. Forbidden Instruction: Do not mount onto plasterboard or paneled walls.

a b

Wall Plate

e f

Concrete Anchor

TV Rail

M4x30mm

Machine Screw

c d

M4/M5/M6/M8

Washer

Lag Bolt

Washer

8mm Lag Bolt

Plastic spacer

Diagram 1-A

Diagram 1-B

FIT SCREEN

2.MOUNT THE TV RAILS TO THE BACK OF YOUR FLAT PANEL TV: Make sure the two TV Rails (b ) are mounted at an equal distance from the top of the TV and as close to the center as possible as shown in diagram 2-A. Knobs should face the outside of the television. M4, M5, M6 and M8 bolts are provided. Plastic Spacers (h) are provided for use with M4,

M5, M6 and M8 TV mount bolts on TV's with curved or recessed back panels as shown in diagram 2-B. If you are mounting to a television with a flat back you will not need a plastic spacer as shown in diagram 2-C. Make sure these bolts are right! Some televisions have shallow threaded inserts; we have provided 4 extra washers you may use to offset this if the provided bolts are too long.

Level with Top

2-A

TV Rail

2-B

2-C

M8x25mm

Machine Screw

M8x40mm

Machine Screw

M5x30mm

Machine Screw

M6x30mm

Machine Screw

SUPPLIED PARTS: Supplied joint parts are exclusive for using in this product. Other joint parts are forbidden to use on this product. If any parts are missing or faulty, telephone the special franchiser for a placement.

FIX TO WALL

Note: This product should be mounted to solid brick, concrete or hard wood batten/studs wall.

1a.SOLID BRICK AND CONCRETE BLOCK MOUNTING: Use the Wall Plate (a) as a template to mark 6 holes

locations on the wall. Three in the top row slots and three more in the bottom row. Make sure these holes are level

and there is at least 200mm between any two holes. Pre-drill these holes with a 10mm masonry bit to at least 90mm

in depth. Insert a Concrete Anchor (e) into each of these holes. Attach the Wall Plate to the wall using 6 Lag Bolts

(d) and 6 Lag Bolt Washers (h).

1b.HARD WOOD WALL MOUNTING: The Wall Plate (a) MUST to be mounted to two wood studs. Use a high quality

stud sensor to locate three adjacent studs. It is a good idea to verify whe re the studs are located with an awl or thin nail

shown in diagram 1-A. Pre-drill a 80mm deep hole at the desired heig ht in each stud using a 6mm drill bit. Use the Wall

Plate as a template to mark the location of the second hole in each stud. Attach the Wall Plate to the wall using the 4 Lag

Bolts (d) and 4 Lag Bolt Washers (h). Make sure the Wall Plate is oriented so the flat surface in the center of the plate in

against the wall shown in diagram 1-B.

Note: Do not use any concrete ancher when you mount the bracket onto hard wood wall.

TV Rail

Close to centered

TV Mounting Hole

Wall

TV Mounting Hole

Wall

ADJUST

3. HANG THE TV ONTO THE WALL PLATE:

First hook the TV Rails over the top of the Wall

Plate (a) in diaram 3-A. Then tighten the safety

screws on the bottom of TV Rails (b) in diagram 3-B.

Finally you can free to adjust your flat panel TV

down to 10 degrees: first loosen one knob, second

loosen the other knob and then adjust the TV which

degree you want. Finally tighten the two knobs.

Diagram 4-A: Front view of the fixed plasma mount

assembled.

Safety screw

3-A

Tighten safety screw

4-A

TENDING INSTRUCTION

Please check whether screws are fixed well each two months.

IF YOU HAVE ANY DOUBTS REGARDING INSTALLATION CONSULT OUR SPECIAL FRANCHISER.

3-B