How it Works
Monoprice
Loading...
38035
User Manual
18 pgs500.52 Kb0

Monoprice 38035 User Manual

Download
Page 1
35" UWQHD 100Hz Zero-G Gaming Monitor
User's Manual
P/N 38035
Page 2
CONTENTS
Controls ....................................................................................................................................................................................... 7
Connections ............................................................................................................................................................................ 8
Notice for FCC ..................................................................................................................................................................... 17
Notice for Industry Canada ...................................................................................................................................... 18
2
Page 3
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.
This device is intended for indoor use only. Do not expose this device to water or moisture of any kind. Do not place
drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately unplug it from the power outlet and allow it to fully dry before reapplying power.
Do not touch the device, the power cord, or any other connected cables
with wet hands.
Do not place the monitor on an unstable surface where it could fall and
cause either personal injury or damage to the monitor and/or other equipment.
Do not expose this device to excessive vibration. Do not subject the product to extreme force, shock, or fluctuations in
temperature or humidity.
Do not expose this device to excessively high temperatures. Do not place
it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
This device ventilates excessive heat through the slots and openings in the
case. Do not block or cover these openings. Ensure that the device is in an open area where it can get sufficient airflow to keep from overheating.
Prior to operation, check the unit and power cord for physical damage. Do
not use if physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet
provides the same type and level of power required by the device.
This device uses a grounded power cord and requires a ground connection
for safe operation. Ensure that the power source has a proper ground connection. Do not modify the plug or use a "cheater" plug to bypass the ground connection.
Unplug this device from the power source when not in use.
3
Page 4
Take care to prevent damage to the power cord. Do not allow it to
become crimped, pinched, walked on, or become tangled with other cords. Ensure that the power cord does not present a tripping hazard.
Never unplug the unit by pulling on the power cord. Always grasp the
connector head or adapter body.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents,
or detergents. For stubborn deposits, moisten the cloth with warm water.
This monitor has no user serviceable parts. Do not open the case or
otherwise attempt to modify this monitor.
Do not leave a single image on the display for a long period of time. Doing
so could cause "burn-in" of the image. It is recommended to use a variable desktop background and to use a screen saver to prevent "burn-in". Alternatively, ensure that the monitor is powered off for at least 2 hours out of every 12.
Keep the original foam packaging material for use when installing or
removing the included stand.
FEATURES
35" display with 1800R curvature 1x HDMI® 2.0, 2x HDMI 1.4, and 1x DisplayPort® 1.2 video inputs 3440 x 1440p @ 100Hz maximum video resolution 178° horizontal and vertical viewing angles 21:9 aspect ratio 8ms response time, 4ms when overdriven 2500:1 contrast ratio 300 cd/m² brightness Supports AMD FreeSync™ 1.0 technology Supports Picture-in-Picture (PiP) and Picture-by-Picture (PbP) display
modes
100 x 100 VESA mounting pattern
4
Page 5
1x 35" Curved Monitor
1x DisplayPort® Cable
SYSTEM REQUIREMENTS
Operating System: Windows® 7/8/10 64-bit or higher
Processor (CPU): Intel® Core™ i5 or AMD Phenom™ II X3 or higher
Graphics Card: NVIDIA® GeForce® GTX950 or AMD Radeon™ R9 380 or higher
Memory: 6GB RAM
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement.
5
Page 6
1x Stand Stem
1x Stand Base
3x K-Head Screws (M4x12)
4x P-Head Screws (M4x10)
4x Wall Mount Screws (Installed)
2x Wall Mount Adapters
1x AC Power Cord
1x User's Manual
6
Page 7
PRODUCT OVERVIEW
Controls
1. MENU: If the OSD menu is not displayed, press the MENU button to access
the OSD menu. If the OSD menu is displayed, press the MENU button to enter a submenu. If editing a value, press the MENU button to save the edited value.
2. DOWN: If the OSD menu is displayed, press the DOWN button to move the
menu highlight down. If editing a value in the OSD menu, press the DOWN button to decrease the value.
3. UP: If the OSD menu is displayed, press the UP button to move the menu
highlight up. If editing a value in the OSD menu, press the UP button to increase the value. If the OSD menu is not displayed, press the UP button to toggle the FPS gaming crosshairs in the middle of the screen on or off and to cycle through the four different crosshair styles.
4. EXIT: If a submenu in the OSD menu is displayed, press the EXIT button to
go back to the previous menu level. If the top level of the OSD menu is displayed, press the EXIT button to close the OSD menu. If editing a value in the OSD menu, press the EXIT button to cancel any changes made and exit editing.
5. POWER: Press the POWER button to turn the monitor on or off.
6. LED INDICATOR: The LED indicates various monitor states. If the LED
INDICATOR is solid blue, solid green, or solid white, the monitor is powered on and is operating normally. It flashes blue when no video source has been detected. It is solid red when no signal is detected or if there is insufficient power received.
7
Page 8
Connections
7. AC POWER SOCKET: NEMA 5-15 socket for connecting the included AC
power cord.
8. AUDIO: 3.5mm stereo jack for connecting headphones, powered speakers,
etc.
9. DISPLAYPORT: DisplayPort® 1.2a video input.
10. HDMI 1: HDMI® 2.0 video input.
11. HDMI 2: HDMI 1.4 video input.
12. HDMI 3: HDMI 1.4 video input.
INSTALLING THE STAND
Perform the following steps to install the stand onto the monitor.
1. Attach the Stand Base to the Stand Stem using the three P-Head Screws,
as shown in the image below.
8
Page 9
2. Remove the monitor from the box and place it face down with the foam
packaging on a table or floor, then remove the rear piece of foam packaging.
3. Press the Button on the back of the monitor, as shown in the image below,
then remove the Stand Plate.
4. Attach the Stand Plate to the Stand Assembly using two K-Head Screws,
as shown in the image above.
5. With the Stand Plate now part of the entire Stand Assembly, insert the
Stand Plate into the back of the monitor until it clicks into place. Ensure that it is securely attached to the monitor.
6. Remove the monitor with the attached Stand Assembly from the foam
packaging and place it on a flat, stable surface.
REMOVING THE STAND
Perform the following steps to remove the installed stand from the monitor.
1. Place the front piece of the original foam packaging material on a table or
on the floor, then place the monitor face down inside the foam.
2. Press the Button on the rear of the monitor to remove the Stand
Assembly.
9
Page 10
Main Menu
Submenu
Options
Description
Input Source
HDMI 1 (2.0)
NONE
Selects the primary video source
HDMI 2 (1.4)
HDMI 3 (1.4)
DP
USING A WALL OR DESK MOUNT
The monitor supports a 100x100 VESA® mounting pattern, allowing it to be used with a compatible wall or desk mount (not included). Perform the following steps to attach the monitor to a mount.
1. Install the wall or desk mount using the instructions included with the
mount.
2. If the included stand was installed, remove it following the instructions in
the
REMOVING THE STAND
installed, press the Button on the rear of the monitor, then remove the Stand Plate.
3. Remove the four Screws revealed by the removal of the Stand Plate, as
shown in image ➊ below.
section above. If the included stand was not
4. Using the four screws removed in the previous step, attach the two Wall
Mount Adapters, as shown in image ➋ above.
5. Following the instructions included with your wall or desk mount and
using the hardware provided, attach the monitor to the mount.
OSD MENU MAP
10
Page 11
Main Menu
Submenu
Options
Description
Brightness/ Contrast
Brightness
0~100
Adjusts the display brightness
Contrast
0~100
Adjusts the display contrast
DCR
On, Off
Turn DCR on or off
Color Setting
Gamma
Gamma 1.8
Sets the Gamma level
Gamma 2.0
Gamma 2.2
Gamma 2.4
Gamma 2.6
Picture Mode
Standard, Photo, Movie, Game, FPS, RTS
Sets the picture mode Color Temperature
Warm, Cool, User
Sets the color temperature
Low Blue Light
0~100
Sets the level of blue light filtering Hue
0~100
Adjusts the hue level
Saturation
0~100
Adjusts the saturation level
Picture Quality Setting
Sharpness
0~100
Sets the display sharpness
Response Time
Off, High, Middle, Low
Adjust the response time
Noise Reduction
Off, High, Middle, Low
Reduces the image noise caused by signal source interference
11
Page 12
Main Menu
Submenu
Options
Description
Picture Quality Setting
Super Resolution
Off, High, Middle, Low
Enhances the image resolution when the actual resolution is low
Dynamic Luminous Control
On, Off
Compensates for gray scale display screen and strengthens the expression of gray scale
Display
Aspect Ratio
Wide Screen, 4:3, 1:1, Auto
Sets the screen aspect ratio LedMode
Normal, Off, Flicker
Adjusts the LED effects
Multi­Window
Multi­Window
Off, PIP Mode, PBP 2Win
Sets the multi-window mode
Sub Win2 Input
DP, HDMI 1, HDMI 2, HDMI 3
Selects the secondary input source for the PiP or PbP window
PIP Size
PIP Mode HDMI 2, Medium, Top Right
Adjusts the PiP or PbP window size
PIP Position
Top Right, Top Left, Bottom Right, Bottom Left
Adjusts the position of the PiP or PbP window Swap
NONE
Swaps the signal source of the main screen and the PiP or PbP window
12
Page 13
Main Menu
Submenu
Options
Description
OSD
Language
English, Chines, Korean, Russian, Spanish, Japanese, French
Sets the language used in the OSD menu
OSD H­Position
0~100
Adjusts the horizontal position of the OSD menu
OSD V­Position
0~100
Adjusts the vertical position of the OSD menu
OSD Transparency
0~100
Sets the overall transparency/ opacity of the OSD menu
OSD Time Out
5~100
Sets the amount of time of inactivity before the OSD menu automatically closes
OSD Rotation
Normal, 90, 180, 270
Rotates the orientation of the OSD menu
Other
DP Version
DP 1.2, Off, Auto Detect
Sets the DisplayPort® version FreeSync
On, Off
Turns AMD FreeSync™ technology
on or off
Reset
NONE
Resets the monitor settings to the factory default values
Note: When choosing the Picture-by-Picture (PbP) function, make the default resolution of each window 1280x1080@60Hz.
13
Page 14
TROUBLESHOOTING
Q1: The screen is blank.
A1: Ensure that power is turned on. Check the brightness/contrast settings. Check
the LED INDICATOR. If it is flashing, no video signal is being received. Check the display settings of the connected device.
Q2: The image is out of focus.
A2: Check the video cable connection.
Q3: The screen is flashing.
A3: There is an issue with the power source. Ensure that devices that could cause
magnetic interference are a safe distance away.
Q4: There is color bleeding, distortion, or other unusual effects.
A4: Check the video cable connection. Connect to another video source for
comparison. Inspect the condition of the ports on the monitor and graphics card. Adjust the color settings in the monitor and PC display settings.
Q5: The screen is scrolling, rolling, or moving.
A5: Check that the source frequency is in the 55-76 Hz range. Check the video
cable connection.
Q6: The LED INDICATOR is off.
A6: Check the power connection. Ensure that power is turned on.
Q7: There is no video signal.
A7: Confirm PC and graphics card compatibility. Inspect the condition of the ports
on the monitor and graphics card.
14
Page 15
Q8: The image is dim.
A8: Adjust the brightness/contrast.
Q9: The image has jitter or a moire pattern.
A9: Nearby electronic equipment may be causing interference.
Q10: The LED INDICATOR is on or flashing, but there is no image on the screen.
A10: Ensure that the monitor is powered on. Confirm the graphics card is properly
installed. Check the video cable connection. Inspect the condition of the ports on the monitor and graphics card. Check to see if the PC is asleep, in standby mode, etc.
Q11: The image position or size is incorrect.
A11: Check the settings in the monitor's OSD menu and PC display settings.
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com. Check the website for support times and links.
15
Page 16
Model
38035
Video Inputs
1x DisplayPort® 1.2, 1x HDMI® 2.0, 2x HDMI 1.4
Display Size
35"
Curvature
1800R
Active Display Area
32.2" x 13.6" (819 x 346 mm)
Panel Type
VA
Panel Model
AUO M350QVR01.1
Maximum Resolution
3440x1440p
Maximum Refresh Rate
100Hz
VESA® Mount Size
100 x 100
AMD FreeSync™ Version
1.0
AMD FreeSync™ Refresh Rates
HDMI 2.0: 48 ~ 100 Hz HDMI 1.4: 48 ~ 65 Hz DisplayPort 1.2: 48 ~ 100 Hz
Aspect Ratio
21:9
Viewing Angles (H/V)
178°/178°
Backlight
LED
Default Color Temperature
6500K
Typical Brightness
Up to 300 cd/m²
Contrast Ratio
2500:1
Maximum Colors
> 16.7 million
Dot Pitch (HxV)
0.2382 x 0.2402 mm
Response Time
8ms (4ms OD)
OSD Languages
English, Chinese, Korean, Russian, Spanish, Japanese, French
Input Power
100 ~ 240 VAC, 50/60 Hz, 2A
SPECIFICATIONS
16
Page 17
Power Consumption
Maximum: 78 watts Typical: 60 watts Standby: ≤ 0.5 watts
Operating Temperature
+32 ~ +104°F (0 ~ +40°C)
Storage Temperature
-4 ~ +140°F (-20 ~ +60°C)
Operating Humidity
10 ~ 85% RH, noncondensing
Dimensions (without stand)
33.0" x 4.8" x 14.8" (837 x 123 x 377 mm)
Dimensions (with stand)
33.0" x 9.8" x 19.0" (837 x 249 x 483 mm)
Weight (with stand)
17.9 lbs. (8.1 kg)
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Modifying the equipment without Monoprice's authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
17
Page 18
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
VESA®, DisplayPort®, and the DisplayPort® logo are registered trademarks of the Video Electronics Standards Association.
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Intel® Core™ i5 is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
AMD® is a registered trademark of Advanced Micro Devices, Inc. in the United States and/or other jurisdictions. Phenom™, Radeon™, and FreeSync™ are trademarks of Advanced Micro Devices, Inc. in the United States and/or other jurisdictions.
NVIDIA® and GEFORCE® are trademarks and/or registered trademarks of NVIDIA Corporation in the U.S. and other countries.
18
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use