How it Works
Monoprice
Loading...
34438
User guide [it]
25 pgs1.18 Mb0
User guide
25 pgs1.35 Mb0
User guide [es]
26 pgs1.06 Mb0
User guide [de]
26 pgs1.32 Mb0
User guide [fr]
26 pgs1.17 Mb0

Monoprice 34438, 34579, 34580 User guide

MP10 3D Printer
P/N 34437, 34577, 34578
User's Manual
CONTENTS
SAFETY WARNINGS AND GUIDELINES ....................................................................................................................................... 3
INTRODUCTION ................................................................................................................................................................................................ 4
FEATURES .............................................................................................................................................................................................................. 4
CUSTOMER SERVICE .................................................................................................................................................................................... 5
PACKAGE CONTENTS ................................................................................................................................................................................. 5
PRODUCT OVERVIEW ................................................................................................................................................................................. 6
INSTALLATION .................................................................................................................................................................................................. 8
SETUP ...................................................................................................................................................................................................................... 10
ASSISTED LEVELING .................................................................................................................................................................................. 13
GLOBAL Z OFFSET LIVE LEVEL ......................................................................................................................................................... 15
OPTIONAL WI-FI SETUP .......................................................................................................................................................................... 15
SOFTWARE INSTALLATION AND SETUP .................................................................................................................................. 17
TECHNICAL SUPPORT .............................................................................................................................................................................. 22
REGULATORY COMPLIANCE ............................................................................................................................................................. 22
2
SAFETY WARNINGS AND GUIDELINES
Be careful not to damage the PC paper on the build plate. Take care to avoid touching hot parts, including heat blocks, extruder nozzle,
extruded filament, and the heated build plate.
Do not wear gloves when operating or repairing to avoid entanglement. Keep the printer and all accessories out of reach of children. Do not remove or disconnect the USB cable when printing from a computer. Do not pull or twist the black cable at any time. Do not force or tear anything during unpacking and setup. This may cause damage
to the printer and/or its accessories.
Do not reach inside the printer during operation. Always allow the printer and extruded filament to cool before reaching inside. Ensure that the printer is turned off and unplugged from its power source before
making repairs or performing service.
Do not install this device on an unstable surface where it could fall and cause either
personal injury or damage to the device and/or other equipment.
Do not subject the product to extreme force, shock, or fluctuations in temperature
or humidity.
This device is intended for indoor use only. Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not touch the device, the power cord, or any other connected cables with wet
hands.
Use only in a well-ventilated area. Do not use in close, confined spaces.
3
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.
Unplug this device from the power source when not in use. Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
INTRODUCTION
Thank you for purchasing this 3D printer from Monoprice! This printer features a single
extruder, which is capable of printing in PLA, ABS, and other materials. You can print from a
Windows® or Mac® PC using a USB connection or can print from 3D model files stored on a
memory card, without the need for a PC connection of any kind. This printer is easy to
setup and easy to use following the instructions in this manual.
FEATURES
Single extrusion print head Can print PLA, ABS, Wood, Copper Fill, Steel Fill, Bronze Fill, and other materials Open frame design for ease of use and maintenance Includes a memory card with Cura, Repetier-Host, and a sample 3D model
4
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com or via email at support@monoprice.com. Check the website for
support times and links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x 3D printer
1x Filament rack
2x Frame brackets
1x Plastic scraper
1x USB cable
1x Memory card
4x Hex wrench (2mm, 2.5mm, 3mm, 4mm)
5x M5x20 screw
13x M4x6 screw
1x Open-end wrench (8mm)
1x AC power cord
1x User's manual
5
PRODUCT OVERVIEW
1. Extruder
2. LCD touch screen
3. Micro USB and microSD™ ports
4. Power switch
5. AC power connector
6
6. Filament holder
7. Feed mechanism
7
INSTALLATION
All instructions assume you are looking at the front of the printer during assembly.
1. Use the packaging material to lay the printer on its side so that you can see the
holes on the bottom. Position the vertical portion of the frame opposite the holes in
the bottom, align the holes on the bottom of the vertical frame with those on the
horizontal frame, then use the included 2.5mm hex wrench and 4x M5x20 screws to
secure the vertical frame to the horizontal frame (2 screws on each side).
8
Loading...
+ 17 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use