Monoprice 7955, 30454, 7956, 30456, 7958 User Manual
Fixed Frame Projection Screen 16:9
P/Ns 7955, 7956, 7958, 30454, 30455, 30456
User's Manual
SAFETY WARNINGS AND GUIDELINES
Please read this manual thoroughly, paying extra attention to these safety warnings and
guidelines. Keep this manual in a safe place for future reference.
This product should only be installed by a qualified structural contractor. Failure to
follow proper structural code in regard to hanging equipment could result in serious
injury or death.
The structure to which this projection screen will be attached must have a minimum
load bearing capacity four times the total weight of the screen and frame.
Frequently inspect the installation for imbalance and signs of wear or damage. Do
not use if repair or adjustment is needed.
Do not touch the screen with your bare hands. The oil on your hands can impact
image quality. Use gloves when handling the screen.
Do not use detergents or cleaning products to clean the screen. Use a soft, lint-free
cloth moistened with warm water.
Two people should be used to attach the screen to the mounting brackets.
Keep the screen covered by a cloth when not in use to prevent dust or dirt from
accumulating on the surface.
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at support@monoprice.com
2
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
3
TOOLS REQUIRED FOR INSTALLATION
The following tools are required for installation and assembly of this projection screen.
Note that these tools are not provided.
INSTALLATION
Mounting Guidelines
Use a carpenter's level to ensure that the brackets are mounted level with each
other. For best results, draw an erasable line on the wall to serve as a guide for the
locations to mount the brackets.
Use a pencil to mark the drill holes through the bracket. Use a carpenter's level to
check that the marked drill holes are level.
If mounting to wood studs, drill a 4mm pilot hole into the stud.
If mounting to a concrete wall or ceiling, drill 5mm anchor holes into the concrete,
then insert the anchors.
Always take care when mounting the screen to properly secure the brackets and
screen to the wall. An unsecure installation can result in the screen falling from its
mounting location. Falling objects can really hurt before they kill you.
4
Frame Assembly
1. Place a blanket on the floor to protect the frame during assembly.
2. Insert the nut plate on one part of one of the horizontal frame package into the
slots on the other half of the horizontal frame package.
3. Align one of the T-joints with the nut plates at the center of the horizontal frame
package, then secure it to the nut place using eight M6x8 screws. Ensure that there
is no gap between the pieces and that it lines up properly before tightening the
screws.
4. Repeat steps 2 and 3 for the other horizontal frame package.
5. Attach a corner piece to each end of the vertical frames using a single M6x8 screw
per piece, as shown in the images below.
6. Turn each horizontal and vertical frame assembly over.
5
7. Slide snap lugs into the slots on the horizontal and vertical frame assemblies and
line them up with the arrows on the assembly.
8. Insert an L-corner piece into the slots at each end of the vertical frame assemblies,
then secure them in place using two M5x5 fixing screws for each piece.
9. Place the vertical and horizontal frame assemblies as shown in the image below,
then join the pieces by inserting the extended L-corner pieces on the vertical
assemblies into the grooves on the horizontal assemblies.
6
Loading...