Please read this entire manual before using this device, paying extra attention
to these safety warnings and guidelines. Please keep this manual in a safe place
for future reference.
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place
drinks or other containers with moisture on or near the device. If
moisture does get in or on the device, immediately unplug it from the
power outlet and allow it to fully dry before reapplying power.
Do not touch the device, the power cord, or any other connected cables
with wet hands.
Do not expose this device to excessively high temperatures. Do not
place it in, on, or near heat sources, such as a fireplace, stove, radiator,
etc. Do not leave it in direct sunlight.
Prior to operation, check the unit and power cord for physical damage.
Do not use if physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet
provides the same type and level of power required by the device.
Unplug this device from the power source when not in use.
2
Page 3
Take care to prevent damage to the power cord. Do not allow it to
become crimped, pinched, walked on, or become tangled with other
cords. Ensure that the power cord does not present a tripping hazard.
Never unplug the unit by pulling on the power cord. Always grasp the
connector head or adapter body.
Ensure that power is turned off and disconnected before making any
electrical connections.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents,
or detergents. For stubborn deposits, moisten the cloth with warm
water.
This device has no user serviceable parts. Do not attempt to open,
service, or modify this device.
INTRODUCTION
Thank you for purchasing this 2x1 DisplayPort Switch! This switch allows you to
connect two DisplayPort video sources to a single DisplayPort display. It
supports video resolutions up to 4K@60Hz and provides up to 21.6 Gbps
bandwidth. It is fully compatible with the DisplayPort 1.2 specification and is
compliant with the VESA DisplayPort standard 1.62, 2.7, and 5.4 Gbps link rates.
3
Page 4
FEATURES
Supports video resolutions up to 4K@60Hz
Provides up to 21.6 Gbps bandwidth
Fully compliant with the DisplayPort 1.2 specification
Supports the RGB, YCbCr 4:4:4, and YCbCr 4:2:2 color spaces
Compliant with the VESA DisplayPort standard 1.62, 2.7, and 5.4 Gbps link
rates
Support for 1, 2, or 4 differential data pairs (lanes)
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that
your ordering, purchasing, and delivery experience is second to none. If you
have any problem with your order, please give us an opportunity to make it
right. You can contact a Monoprice Customer Service representative through
the Live Chat link on our website www.monoprice.com during normal business
hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-6pm PT) or via email at
support@monoprice.com
4
Page 5
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the
items listed below. If anything is missing or damaged, please contact
Monoprice Customer Service for a replacement.
1x 2x1 DisplayPort switch
1x AC power adapter (5 VDC, 1A)
1x User's manual
PRODUCT OVERVIEW
1. PWR LED: The LED illuminates when power is applied.
2. DC 5V: DC barrel connector for connecting the included AC power
adapter.
3. DP OUT: DisplayPort connector for connecting to the DisplayPort display.
4. IN1 IN2: Switch for selecting one of the two inputs.
5
Page 6
5. DP IN 1: DisplayPort connector for connecting a DisplayPort source.
6. DP IN 2: DisplayPort connector for connecting a DisplayPort source.
SAMPLE CONNECTION DIAGRAM
6
Page 7
INSTALLATION
1. Ensure that all equipment to be connected is powered off and
unplugged from its power source.
2. Place or mount the switch in its intended location.
3. Using a DisplayPort 1.2 cable (not included), plug one end into the
DisplayPort display, then plug the other end into the DP OUT port on the
switch.
4. Using a DisplayPort 1.2 cable (not included), plug one end into the DP IN 1
port on the switch, then plug the other end into the DisplayPort output
on your video source device.
5. Using a DisplayPort 1.2 cable (not included), plug one end into the DP IN
2 port on the switch, then plug the other end into the DisplayPort output
on your video source device.
6. Plug the DC barrel connector on the included AC power adapter into the
DC 5V jack on the switch, then plug the adapter into a nearby AC power
outlet. The PWR LED will illuminate, indicating that power has been
applied.
7. Plug in and power on all connected equipment. Start video playback on
each connected source device. Verify that the video can be seen on the
display and that you can switch between the two video sources.
7
Page 8
Model
24568
Inputs
2x DisplayPort 1.2
Outputs
1x DisplayPort 1.2
Maximum Video Resolution
4K@60Hz
Maximum Bandwidth
21.6 Gbps
Color Spaces
RGB, YCbCr 4:4:4, YCbCr 4:2:2
Link Rates
1.62, 2.7, and 5.4 Gbps
Differential Data Pairs (Lanes)
1, 2, or 4
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist
you with any questions you may have about installation, setup,
troubleshooting, or product recommendations. If you ever need assistance with
your new product, please come online to talk to one of our friendly and
knowledgeable Tech Support Associates. Technical support is available through
the online chat button on our website www.monoprice.com during regular
business hours, 7 days a week. You can also get assistance through email by
sending a message to tech@monoprice.com
SPECIFICATIONS
8
Page 9
Input Power
5 VDC, 1A
AC Adapter Input Power
100 ~ 240 VAC, 50/60 Hz
Maximum Power Consumption
1.3 watts
Operating Temperature
+32 ~ +104°F (0 ~ +40°C)
Storage Temperature
-4 ~ +140°F (-20 ~ +40°C)
Operating Humidity
20 ~ 90% RH, non-condensing
Dimensions
2.8" x 2.4" x 0.8" (71 x 61 x 21 mm)
Weight
4.5 oz. (127 g)
REGULATORY COMPLIANCE
Notice for FCC
Modifying the equipment without Monoprice’s authorization may result in the
equipment no longer complying with FCC requirements for Class B digital
devices. In that event, your right to use the equipment may be limited by FCC
regulations, and you may be required to correct any interference to radio or
television communications at your own expense.
9
Page 10
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
10
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.