Page 1
MONOPRICE
Blackbird™ HDMI® Bi-Directional Switch
P/N 24280
User's Manual
Page 2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these
safety warnings and guidelines. Please keep this manual in a safe place for future reference.
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not touch the device, the power cord, or any other connected cables with wet
hands.
Do not expose this device to excessively high temperatures. Do not place it in, on,
or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct
sunlight.
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.
Unplug this device from the power source when not in use.
Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
Ensure that power is turned off and disconnected before making any electrical
connections.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or
detergents. For stubborn deposits, moisten the cloth with warm water.
This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.
2
Page 3
INTRODUCTION
Thank you for purchasing this Blackbird™ HDMI® Bi-Directional Switch! This switch
functions as a 2x1 switch, as well as a 1x2 splitter, depending on how it is connected. It
supports 3D video, multichannel audio, and is compliant with the HDMI 1.4 specification.
FEATURES
Functions as a 2x1 switch or 1x2 splitter
Supports 3D video
Compliant with the HDMI® 1.4 specification
Supports high-definition multichannel audio
Can be powered using a USB power source
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at support@monoprice.com
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x HDMI® bi-directional switch
1x User's manual
3
Page 4
SAMPLE CONNECTION DIAGRAM
INSTALLATION
2x1 Switch
Perform the following steps to install this device as a 2x1 Switch.
1. Ensure that all equipment to be connected is powered off and unplugged from its
power source.
2. Note that one side of the switch has a single HDMI® port, while the other side has
two HDMI ports. Using a High Speed HDMI Cable (not included), plug one end into
the HDMI input on your television, then plug the other end into the side with a
single HDMI port.
3. Using a High Speed HDMI Cable (not included), plug one end into one of the HDMI
ports on the side with two ports, then plug the other end into the HDMI output on
one of your video source devices. Repeat for the second video source device.
4. (Optional) Using a mini USB cable (not included), plug the cable into the USB/Power
jack on the switch, then plug the other end into a USB power source (not included).
4
Page 5
5. Plug in and power on all connected equipment. Start video playback on each source
device. Verify that you can see video on the display and that you can switch
between the two source devices using the 1/2 switch.
1x2 Splitter
Perform the following steps to install the switch as a 1x2 Splitter.
1. Ensure that all equipment to be connected is powered off and unplugged from its
power source.
2. Note that one side of the switch has a single HDMI® port, while the other side has
two HDMI ports. Using a High Speed HDMI Cable (not included), plug one end into
the HDMI input on one of your televisions, then plug the other end into one of the
HDMI ports on the side with two ports. Repeat for the other television.
3. Using a High Speed HDMI Cable (not included), plug one end into the HDMI port on
the side with a single port, then plug the other end into the HDMI output on your
video source device.
4. (Optional) Using a mini USB cable (not included), plug the cable into the USB/Power
jack on the switch, then plug the other end into a USB power source (not included).
5. Plug in and power on all connected equipment. Start video playback on the source
device. Verify that you can see video on both displays. Note that the 1/2 switch has
no effect when configured as a splitter.
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
during regular business hours, 7 days a week. You can also get assistance through email by
sending a message to tech@monoprice.com
5
Page 6
REGULATORY COMPLIANCE
Notice for FCC
Modifying the equipment without Monoprice’s authorization may result in the equipment no
longer complying with FCC requirements for Class B digital devices. In that event, your right to use
the equipment may be limited by FCC regulations, and you may be required to correct any
interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
Blu-ray Disc™ and Blu-ray™ are trademarks of the Blu-ray Disc Association.
6
Loading...