Page 1
MONOPRICE
Blackbird™ 4K HDBaseT™ Extender Kit
P/N 21792
User's Manual
Page 2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these
safety warnings and guidelines. Please keep this manual in a safe place for future reference.
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not touch the device, the power cord, or any other connected cables with wet
hands.
Do not expose this device to excessively high temperatures. Do not place it in, on,
or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct
sunlight.
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Unplug this device from the power source when not in use.
Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
Ensure that power is turned off and disconnected before making any electrical
connections.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or
detergents. For stubborn deposits, moisten the cloth with warm water.
This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.
2
Page 3
INTRODUCTION
Thank you for purchasing this Blackbird™ 4K HDBaseT™ Extender Kit! This kit consists of a
transmitter and receiver, which allows a 1080p HDMI® signal to be transmitted to distances
up to 328 feet (100 meters) and a 4K signal to be transmitted to distances up to 229 feet
(70 meters) over a single Cat6 Ethernet cable. It supports video resolutions up to 4K@60Hz
4:4:4 and includes the Power over HDBaseT (PoH) feature, which allows the transmitter or
receiver to be powered by the other device over the Ethernet cable. It supports bi-
directional extension of infrared remote control, RS232 computer data, and 10/100Mbps
Ethernet network traffic. It is fully compliant with the HDMI 2.0 and HDCP 2.2 specifications
and provides up to 18Gbps bandwidth.
FEATURES
Supports video resolutions up to 4K@60Hz 4:4:4
Extends 1080p signals to distances up to 328 feet (100 meters) and 4K signals to
distances up to 229 feet (70 meters)
Fully compliant with the HDMI 2.0 and HDCP 2.2 specifications
Supports the Power over HDBaseT feature, which allows the transmitter or receiver
to be powered by the other device over the Ethernet cable
Supports bi-directional IR and RS232 pass-through
Supports HDR
Includes a 4-port 10/100Mbps Ethernet switch
3
Page 4
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at support@monoprice.com
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x HDBaseT™ transmitter
1x HDBaseT receiver
2x 3-pin to DB9 RS232 cables
4x Mounting brackets
8x Screws
1x IR transmitter
1x IR receiver
8x Plastic cushions
1x User's manual
4
Page 5
PRODUCT OVERVIEW
Transmitter
1. RS232 MODE Switch: Selects the RS232 mode. The CTRL position is the normal
operating mode where RS232 data is passed back and forth with the receiver. The
two UPDATE positions are for updating the transmitter's firmware using one of two
methods. See the
2. LINK LED Indicator: The LED illuminates green when there is a valid HDBaseT
connection with the receiver. The LED is off when there is no valid link.
3. HDCP LED Indicator: The LED illuminates green when there is HDMI video traffic
with HDCP. It will blink green when there is HDMI® video traffic without HDCP and
will be off when there is no HDMI video traffic.
4. POWER LED Indicator: The LED illuminates red when power is applied and is off
when no power is present.
FIRMWARE UPDATE
section for details.
5. RS232 Connector: Connector for the included 3-pin to DB9 RS232 cable.
6. IR IN Jack: 3.5mm jack for connecting the IR receiver.
7. IR OUT Jack: 3.5mm jack for connecting the IR transmitter.
5
Page 6
8. HDMI IN Port: HDMI® port for connecting the HDMI cable from the video source
device.
9. HDBT OUT Jack: RJ45 jack for connecting the Ethernet cable to the receiver.
10. ETHERNET Jacks: RJ45 jacks for connecting to an existing Ethernet network and/or
devices.
11. DC IN Jack: DC barrel connector for connecting the included AC power adapter.
Receiver
1. RS232 MODE Switch: Selects the RS232 mode. The CTRL position is the normal
operating mode where RS232 data is passed back and forth with the transmitter.
The two UPDATE positions are for updating the receiver's firmware using one of
two methods. See the
2. LINK LED Indicator: The LED illuminates green when there is a valid HDBaseT™
connection with the receiver. The LED is off when there is no valid link.
3. HDCP LED Indicator: The LED illuminates green when there is HDMI® video traffic
with HDCP. It will blink green when there is HDMI video traffic without HDCP. It will
be off when there is no HDMI video traffic.
4. POWER LED Indicator: The LED illuminates red when power is applied and is off
when no power is present.
FIRMWARE UPDATE
section for details.
6
Page 7
5. RS232 Connector: Connector for the included 3-pin to DB9 RS232 cable.
6. IR IN Jack: 3.5mm jack for connecting the IR receiver.
7. IR OUT Jack: 3.5mm jack for connecting the IR transmitter.
8. HDMI OUT Port: HDMI port for connecting the HDMI® cable to the video display.
9. HDBT IN Jack: RJ45 jack for connecting the Ethernet cable to the transmitter.
10. ETHERNET Jacks: RJ45 jacks for connecting to an existing Ethernet network and/or
devices.
11. DC IN Jack: DC barrel connector for connecting the included AC power adapter.
SAMPLE CONNECTION DIAGRAM
7
Page 8
INSTALLATION
Perform the following steps to install this HDBaseT™ Extender Kit.
1. Ensure that all equipment to be connected is powered off and unplugged from its
power source.
2. Place the transmitter and receiver in their intended locations. Use the included
mounting brackets to secure the units in place, as desired.
3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input
on your display, then plug the other end into the HDMI OUT port on the receiver.
4. Using a Cat6 Ethernet cable (not included), plug one end into the HDBT IN jack on
the receiver, then plug the other end into the HDBT OUT jack on the transmitter.
Note that if this cable is to be run in or through wall, it must be rated for in-wall use.
5. Using a High Speed HDMI Cable (not included), plug one end into the HDMI IN port
on the transmitter, then plug the other end into the HDMI output on your video
source device (e.g., Blu-ray Disc™ player, DVD player, game console, etc.).
6. (Optional) Using an Ethernet cable (not included), plug one end into one of the
ETHERNET ports on either the transmitter or receiver, then plug the other end into
an Ethernet port on a network router or switch.
7. (Optional) Using an Ethernet cable (not included), plug one end into an available
ETHERNET port on the transmitter or receiver, then plug the other end into the
Ethernet port on your computer, Ethernet switch, or other network device. Repeat
for up to two additional network connections.
8. (Optional) If you want to control the video source device from the remote location,
plug the included IR receiver into the IR IN jack on the receiver, then position the IR
"eye" where it can receive IR signals from your remote control. Alternatively, if you
want to control the remote display from the source side, plug the included IR
receiver into the IR IN jack on the transmitter, then position the IR "eye" where it can
receiver IR signals from your remote control.
9. (Optional) If you want to control the video source device from the remote location,
plug the included IR transmitter into the IR OUT jack on the transmitter, then
position the IR emitter where it can transmit IR signals to the IR "eye" on the video
8
Page 9
source device. Alternatively, if you want to control the remote display from the
source end, plug the include IR transmitter into the IR OUT jack on the receiver, then
position the IR emitter where it can transmit IR signals to the IR "eye" on the display.
10. Plug the DC barrel connector on the included AC power adapter into the DC IN jack
on either the transmitter or the receiver, the plug the adapter into a nearby AC
power outlet. Note that the unit that is not connected to the AC power adapter will
receive its power from the other unit over the Cat6 Ethernet cable.
11. Plug in and power on all connected equipment. Start video playback on your source
device, then verify that you can see the video on the remote display. If you are
using the IR extension feature, verify that you can control the intended device from
the other end. If you connected computers or other network devices to the
ETHERNET ports, verify that you have network access to the connected device.
FIRMWARE UPDATE
Perform the following steps to update the firmware for both the transmitter and receiver.
1. Plug the included 3-pin to DB9 RS232 Cable into the 3-pin RS232 connector on the
receiver or transmitter, then plug the other end into the RS232 serial connector on
your PC.
2. If you will be updating the Valens IC program, slide the RS232 Mode Switch to the
UPDATE A position. If you will be update the Compression IC program, slide the
RS232 Mode Switch to the UPDATE B position instead.
3. Locate the update batch (.bat) file on your computer and double-click it to run it.
9
Page 10
TECHNICAL SUPPORT
Model
21792
Maximum Transmission Distance
up to 328 feet (100m) for 1080p signals
up to 229 feet (70m) for 4K signals
Maximum Resolution
4K@60Hz 4:4:4
Maximum Bandwidth
18Gbps
HDMI® Standards
HDMI 2.0 and HDCP 2.2
Ethernet Standard
10/100Mbps
Power Source
24 VDC, 1.25A AC adapter or PoH
AC Adapter Input Power
100 ~ 240 VAC, 50/60 Hz
Maximum Power Consumption
20 watts
Operating Temperature
+14 ~ +122°F (-10 ~ +50°C)
Operating Humidity
0 ~ 90% RH, non-condensing
Dimensions (each)
6.0" x 0.6" x 4.1" (152 x 16 x 104 mm)
Weight (each)
8.5 oz. (240g)
Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
during regular business hours, 7 days a week. You can also get assistance through email by
sending a message to tech@monoprice.com
SPECIFICATIONS
10
Page 11
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Modifying the equipment without Monoprice’s authorization may result in the equipment
no longer complying with FCC requirements for Class B digital devices. In that event, your
right to use the equipment may be limited by FCC regulations, and you may be required to
correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
11
Page 12
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Blackbird™ is a trademark of Monoprice Inc.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
12
Loading...