How it Works
Monoprice
Loading...
18784
User Manual
13 pgs262.07 Kb0

Monoprice 18784 User Manual

Download
Page 1
MONOPRICE
Blackbird™ HDMI® Extender Over Cat6, 50m
P/N 18784
User's Manual
Page 2
CONTENTS
Transmitter .................................................................................................................................................................................................... 6
Receiver ............................................................................................................................................................................................................ 7
Notice for FCC .......................................................................................................................................................................................... 12
Notice for Industry Canada ........................................................................................................................................................... 13
2
Page 3
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these
safety warnings and guidelines. Please keep this manual in a safe place for future reference.
This device is intended for indoor use only. Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not touch the device, the power cord, or any other connected cables with wet
hands.
Do not expose this device to excessively high temperatures. Do not place it in, on,
or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct
sunlight.
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.
Unplug this device from the power source when not in use. Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
Ensure that power is turned off and disconnected before making any electrical
connections.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or
detergents. For stubborn deposits, moisten the cloth with warm water.
This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.
Keep away from corrosive materials.
3
Page 4
INTRODUCTION
Thank you for purchasing this Blackbird™ HDMI® Extender! This extender allows you to
transmit a 1080p video signal to distances up to 164 feet over a single Cat6 UTP cable. It
features a 4.95Gbps bandwidth and includes an HDMI pass-through port, which allows for
cascading. Display EDID information can be set to either the display connected to the
receiver or the display connected to the pass-through port on the transmitter. It supports
Deep Color up to 12-bits/channel and multichannel high-definition audio streams, such as
DTS-HD Master Audio™ and Dolby TrueHD™. This extender also features a bidirectional IR
transmitter and receiver, which allows you to control your source device from the remote
location or your remote display from the source location.
FEATURES
Supports HDMI® video resolutions up to 1920 x 1080p @ 60Hz 4.95 Gbps bandwidth Can transmit signals to distances up to 164 feet (50m) over a single Cat6 UTP cable EDID information can be obtained from the display connected to either the receiver
or to the transmitter's pass-through port
Includes a bidirectional IR extender for control of source devices from the remote
location or the remote display from the source location
Features a pass-through HDMI port on the transmitter for connecting a second
display or another extender transmitter
Supports HDCP version 1.4
4
Page 5
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at support@monoprice.com
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x HDMI® extender transmitter
1x HDMI extender receiver
1x Wideband IR transmitter (blaster)
1x Wideband IR receiver
2x 5 VDC, 1A AC power adapters
1x User's manual
5
Page 6
PRODUCT OVERVIEW
Transmitter
1. IR Out: Connection for the IR transmitter or IR receiver.
2. EDID: Switch to allow EDID information to be obtained from either the display
connected to the receiver or the display connected to the pass-through port on the
transmitter.
3. Power LED: Illuminates when power is applied.
4. Link LED: Illuminates when a valid link between the transmitter and receiver exists.
5. HDMI® In: Connection for the HDMI source device.
6. HDMI Out: Pass-through connector for connecting a display or cascading another
extender transmitter.
7. CAT: Connection for the Cat6 Ethernet cable.
8. DC5V: Connection for the AC power adapter.
6
Page 7
Receiver
1. IR In: Connection for the IR receiver or transmitter.
2. Power LED: Illuminates when power is applied.
3. Link LED: Illuminates when a valid link between the transmitter and receiver exists.
4. EQ: Adjusts the signal strength to eliminate video noise or anomalies.
5. HDMI Out: Connection for the video display.
6. CAT: Connection for the Cat6 Ethernet cable.
7. DC5V: Connection for the AC power adapter.
7
Page 8
INSTALLATION
Perform the following steps to install the extender:
1. Ensure that all equipment to be connected is powered off and unplugged from its
power source.
2. Place the extender receiver at the remote location.
3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input
on your display, then plug the other end into the HDMI Out port on the receiver.
4. (Optional) Plug either the IR receiver or IR transmitter into the IR In port on the
receiver. If you want to control the source device from the remote location, use the
IR receiver. If you want to control the remote display from the source location, use
the IR transmitter instead.
5. If using the IR receiver, position the "bulb" where it can receive signals from your
remote control. If using the IR transmitter, position the "bulb" where it can transmit
signals to the IR receiver on your display.
6. Route a Cat6 Ethernet cable (not included) from the source location to the remote
location. This cable can be no longer than 164 feet (50 meters) and must be rated for
in-wall use if being routed inside or through the walls.
8
Page 9
7. Connect one end of the Cat6 Ethernet cable to the CAT port on the receiver.
8. Place the extender transmitter at the source location.
9. Connect one end of the Cat6 Ethernet cable to the CAT port on the transmitter.
10. (Optional) Using a High Speed HDMI Cable (not included), plug one end into the
HDMI® input on a display at the source location or into the HDMI input of another
extender or other HDMI device. Plug the other end into the HDMI Out port on the
transmitter.
11. Using a High Speed HDMI Cable (not included), plug one end into the HDMI In port
on the transmitter, then plug the other end into the HDMI output of your HDMI
source device (e.g., DVD or Blu-ray Disc™ player).
12. (Optional) Plug either the IR receiver or IR transmitter into the IR Out port on the
transmitter. If you want to control the source device from the remote location, use
the IR transmitter. If you want to control the remote display from the source
location, use the IR receiver instead.
13. If using the IR transmitter, position the "bulb" where it can transmit signals to the IR
receiver on your source device. If using the IR receiver, position the "bulb" where it
can receive signals from your remote control.
14. Slide the EDID switch on the transmitter to the Left position if you want to obtain
EDID information from the remote display. If you want to obtain EDID information
from a display connected to the pass-through HDMI connector on the transmitter,
slide the switch to the Right position instead.
15. Plug the DC barrel connector on one of the AC power adapters into the DC5V jack
on the receiver, then plug the adapter into a nearby AC power outlet. Verify that
the Power LED illuminates.
16. Plug the DC barrel connector on the other AC power adapters into the DC5V jack on
the transmitter, then plug the adapter into a nearby AC power outlet. Verify that
the Power LED illuminates.
17. Verify that the Link LED illuminates. It may take several minutes before a handshake
is achieved.
9
Page 10
18. Plug in and power on all connected equipment. Start video playback on your HDMI®
EQ Switch Positions
Approximate Cat6 Cable Length
up to 49 feet (15 meters)
49 ~ 98 feet (15 ~ 30 meters)
98 ~ 131 feet (30 ~ 40 meters)
131 ~ 164 feet (40 ~ 50 meters)
source device.
19. Verify that video is visible on the remote display
20. If you are using the IR extender, verify that you can control the source device from
the remote location or the remote display from the source location.
Congratulations, your HDMI extender is properly installed!
SETTING THE EQ SWITCH
If you see flickering, blinking, or other video anomalies on the remote display, use the EQ
Switches to increase the signal strength. Start with the EQ set to 0, then increase it until
the video anomalies are no longer present. The positions for each of the three DIP switches
for each number value and the approximate HDMI cable length range can be found in the
following table.
10
Page 11
SPECIFICATIONS
Model
18784
HDMI® Version
1.3
HDCP Version
1.4
Video Bandwidth
4.95 Gbps
Maximum Video Resolution
1920 x 1080p @ 50/60 Hz
Transmission Medium
Single Cat6 UTP cable
Maximum Transmission Distance
164 feet (50 meters)
Color Depth
10-bits or 12-bits / channel
Color Space
RGB 4:4:4, YCbCr 4:4:4, YCbCr 4:2:2
Supported Audio Formats (Pass-Through)
2/5.1/7.1-channel LPCM, Dolby® Digital™,
5.1-channel DTS®, Dolby Digital Plus™,
Dolby TrueHD™, DTS-HD Master Audio™,
Dolby Atmos®
IR Frequency Range
30 ~ 60 kHz
Power Source
5 VDC, 1A AC power adapter
AC Power Adapter Input Power
100 ~ 240 VAC, 50/60 Hz
Transmitter Power Consumption
1.5 watts
Receiver Power Consumption
1.0 watts
Operating Temperature
+32 ~ +104°F (0 ~ +40°C)
Storage Temperature
-4 ~ +140°C (-20 ~ +60°C)
Humidity
20 ~ 90% RH, non-condensing
Dimensions (each)
3.5" x 2.2" x 0.7" (88 x 57 x 18 mm)
Weight (each)
7.1 oz. (200g)
Regulatory Compliance
CE, FCC, UL
11
Page 12
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Modifying the equipment without Monoprice’s authorization may result in the equipment
no longer complying with FCC requirements for Class B digital devices. In that event, your
right to use the equipment may be limited by FCC regulations, and you may be required to
correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
12
Page 13
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Blackbird™ is a trademark of Monoprice Inc.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
DTS® is a registered trademark and the DTS logos, Symbol, DTS-HD™, and DTS-HD Master Audio™ are trademarks of DTS, Inc.
Dolby®, Dolby Atmos®, and the double-D symbol are registered trademarks of Dolby Laboratories. Dolby Digital™, Dolby Digital Plus®, and Dolby TrueHD® are trademarks of Dolby Laboratories.
Blu-ray Disc™, Blu-ray™, and the logos are trademarks of the Blu-ray Disc Association.
13
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use