Page 1
Page 2
SAFETY WARNINGS AND GUIDELINES
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place
drinks or other containers with moisture on or near the device. If moisture
does get in or on the device, immediately unplug it from the power outlet and
allow it to fully dry before reapplying power.
Use only in a well-ventilated area. Do not use in close, confined spaces.
The extrusion nozzle of this printer operates at high temperatures. Take care to
avoid touching the nozzle and any newly extruded material. Take care to not
touch the nozzle to flammable materials.
Always allow the nozzle and extruded material to cool before touching.
Some types of filament can emit a strong odor when heated. Always use this
printer in a well-ventilated area.
Do not use the printer near a heat source, such as a fireplace, heating vent,
radiator, etc. Do not leave it in direct sunlight.
This printer is suitable for use by children as young as 8 years old. Children
should always be closely supervised by a responsible adult when using this
printer.
INTRODUCTION
Thank you for purchasing this 3D Printing Pen! This pen printer allows you to create
3D models or repair 3D models by hand. It has low-temperature and high-temperature
print settings, for use with eMate and PLA filaments. It supports temperatures from
80 ~ 195°C and has eight print speed settings. It is suitable for use by children as
young as 8 years old, though they should always be closely supervised by an adult.
2
Page 3
FEATURES
Low-temperature setting for use with 1.75mm eMate filament
Variable low-temperature settings from 80 ~ 90°C
High-temperature setting for use with 1.75mm PLA filament
Variable high-temperature settings from 80 ~ 195°C
USB powered and compatible with USB power banks
Eight speed settings from 0 ~ 120 cm/minute
0.7mm extrusion nozzle
Automatic and manual extrusion modes
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your
ordering, purchasing, and delivery experience is second to none. If you have any
problem with your order, please give us an opportunity to make it right. You can
contact a Monoprice Customer Service representative through the Live Chat link on
our website www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm
PT, Sat-Sun: 9am-6pm PT) or via email at support@monoprice.com
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items
listed below. If anything is missing or damaged, please contact Monoprice Customer
Service for a replacement.
1x 3D Printing Pen
1x USB Power Cable
1x USB Power Adapter
1x User's Manual
3
Page 4
PRODUCT OVERVIEW
1. Filament Feed Hole
2. LCD Display
3. Temperature Adjustment Buttons
4. LED Indicators
5. Speed Control Buttons
6. Extrusion Nozzle
7. Filament Feed/OK Button
8. Filament Retreat/Mode Selection
Button
9. Hanging Hook
10. DC Power Connector
OPERATION
1. Plug the included USB Power Adapter into a nearby AC power outlet.
2. Plug the included USB Power Cable into the DC Power
Connector (10) on the pen, then plug the other end into
the USB port on the USB Power Adapter. The first LED
Indicator (3) will illuminate yellow to indicate that power
is applied.
3. Press the Filament Retreat/Mode
Selection Button (8) to cycle between
low-temperature and high-
temperature modes. The LCD Display
(2) will show [ L ] for low-temperature
mode or [ H ] for high-temperature mode. The default temperature is 90°C for
low-temperature mode and 195°C for high-temperature mode.
4
Page 5
4. (Optional) While [ L ] or [ H ] is displayed, use the Temperature Adjustment
Buttons (3) to change the temperature setting from the default values of 90°C
or 195°C.
5. Press the Filament Feed/OK Button (7)
to confirm the temperature setting.
The second LED Indicator (4) will
illuminate red to indicate that the print
nozzle is being heated. While the
nozzle is heating, the LED Display (2)
will show the actual temperature.
6. When the target temperature is
reached, the second LED Indicator (2)
will change from red to blue, indicating
that the pen is ready to print.
7. Use a pair of scissors or side cutters to cut
the end of your filament so that the filament
end is cut evenly.
8. Insert your filament into the Filament Feed
Hole (1) until you reach resistance.
While gently holding the filament
against the resistance, press and hold
the Filament Feed/OK Button (2) to
feed the filament into the pen until it
extrudes out of the nozzle.
9. Press and hold the Filament Feed/OK
Button (2) to feed filament and print
with the pen. Alternatively, double-
press it to engage automatic feeding.
Automatic feeding can be stopped at
any time by pressing the Filament
Feed/OK Button (2) once.
5
Page 6
10. If you wish to change the speed of
filament extrusion, use the Speed
Control Buttons (5). There are 8 speed
settings, from 1 to 8, with 6 being the
default.
11. When you are finished printing or
when you want to change filament,
double-press the Filament
Retreat/Mode Selection Button (8) to
remove the filament.
OPERATING NOTES
The pen will automatically go into standby mode if no buttons are pressed for
90 seconds.
When using the [ H ] mode and switching to the [ L ] mode, the pen will
gradually cool down over the course of 90 seconds and will automatically
extract the installed PLA filament.
You can adjust the print temperature on the fly, but by no more than ±15°C.
When switching modes between [ H ] and [ L ], the pen will remember the
temperature you had last set for each mode in the range 90 ~ 135°C for [ L ]
mode and 135 ~ 195°C for [ H ] mode.
If the screen shows E1 and the blue LED flashes, or if it shows E2, please
contact Monoprice Technical Support for assistance.
In the event of any other serious operating error, please contact Monoprice
Technical Support for assistance.
6
Page 7
Model
16275
Nozzle Diameter
0.7mm
Filament Diameter
1.75mm
Supported Filament Types
eMate, PLA
Print Speeds
0 ~ 120 cm/minute
Working Temperature
80~ 195°C
[ L ] Default Temperature (eMate)
90°C
[ L ] Adjustment Range (eMate)
80 ~ 90°C
[ H ] Default Temperature (PLA)
195°C
[ H ] Adjustment Range (PLA)
80 ~ 195°C
Power Source
USB, 5 VDC, 2A
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with
any questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come
online to talk to one of our friendly and knowledgeable Tech Support Associates.
Technical support is available through the online chat button on our website
www.monoprice.com during regular business hours, 7 days a week. You can also get
assistance through email by sending a message to tech@monoprice.com
SPECIFICATIONS
7
Loading...