Monoprice 13816, 13815 User Manual

Aluminum Triple Monitor Desk Stand 15" - 30"

P/N: 13816

User's Manual

INTRODUCTION

Thank you for purchasing this Triple Monitor Desk Stand!

This desk stand is capable of mounting three 15 " ~ 30" monitors, with 75 x 75 or 100 x 100

VESA® mounting patterns and weighing up to 22 lbs. each. It allows for overall height,

individual height, tilt, swivel, and horizontal adjustments, and includes cable management

clips and all the hardware necessary to assemble the stand and mount two monitors.

Additionally, the monitors can be rotated 360° for easy portrait/landscape orientation

adjustment.

FEATURES

 Compatible with 15" ~ 30" monitors
 Supports three monitors weighing up to 22 lbs. (10 kg) each
 Compatible with 75 x 75 and 100 x 100 VESA® mounting patterns
 Overall height, individual height, tilt, swivel, rotation, and horizontal position

adjustments

 Includes cable management clips
 Includes all necessary mounting hardware

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [e-mail]

2

PACKAGE CONTENTS

A Arm Assembly

B Base

C Pole Assembly

D ø8.0 x ø5.5 x 5.0 mm Bushings (x12)

E Short M4x12 Screws (x12)

F Long M4x12 Screws (x12)

G 4mm Hex Wrench

H 5mm Hex Wrench

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

3

INSTALLATION

1. Place the Base (B) on a desk or table.

2. Insert the Pole Assembly (C) into the hole in the base,

then turn it clockwise to tighten the connection.

3. Place the Arm Assembly (A) onto the Pole Assembly

(C), adjust the height as desired, then use the 4mm

Hex Wrench (G) to tighten the screw as shown in the

following figure to the right. You can also adjust the

height by loosening the lock collar and extending the

pole assembly up or down as desired.

4. Place a towel or blanket on a table or on the floor, then place one of your monitors

face down on the towel/blanket.

5. Insert two (2) Short M4x12 Screws (E) or Long M4x12 Screws (F) into the upper two

VESA® mounting holes. Tighten them to the point where there is 2-4mm between

the back of the monitor and the screw head. If necessary, use the ø8.0 x ø5.5 x 5.0

mm Bushings (D) to reduce the space between the screw heads and the back of the

monitor.

4

6. Repeat steps 4 and 5 for the second and third monitors.

7. Place one of the monitors onto a mounting bracket by placing the extended screws

into the grooves on the bracket. Place the first monitor in the center to ensure the

mount remains stable.

8. Insert two (2) additional Short M4x12 Screws (E) or Long M4x12 Screws (F) through

the bracket into the lower VESA mounting holes. Tighten the screws to secure the

bracket to the back of the monitor. Use the ø8.0 x ø5.5 x 5.0 mm Bushings (D) as

necessary to reduce the space between the screw heads and the back of the

monitor.

9. Repeat steps 7 and 8 for the second and third monitors, mounting them to either

side of the central monitor.

5

10. Loosen the two thumbscrews that hold each bracket to the mounting arm, then

slide the monitor and bracket assemblies so that the monitor bezels are almost

touching, as shown in the figure to the right. Tighten the thumbscrews to secure

the brackets in place.

11. If the monitors are not level, use the included 4mm Hex Wrench (G) to tighten the

screw at the top of the lower bracket(s), thereby raising the bracket's level. To lower

the bracket's level, loosen the screw.

6

12. To adjust the tilt, first use the included 5mm Hex Wrench (H) to slightly loosen the

two screws on each side of the mounting bracket, adjust the tilt as desired, then

tighten the screws to secure the bracket in place.

13. To adjust the monitor angles, use the included 5mm Hex Wrench (H) to slightly

loosen the two screws at the base of the arms, adjust the angle, then tighten the

screws to secure the arms in place.

14. Install the cables and use the included cable management clips to keep hold the

cables neatly in place.

7

TECHNICAL SUPPORT

Model

13816

Number of Supported Monitors

Three (3)

Supported TV Sizes

15" ~ 30"

Maximum Supported Weight

22 lbs. (10 kg) per monitor

Supported VESA Sizes

75 x 75 and 100 x 100

Height Adjustment Range

12.0" ~ 17.7" (304 ~ 450 mm)

Swivel Adjustment Range

Up to 150°

Rotation Adjustment Range

360°

Tilt Adjustment Range

±12°

Monoprice is pleased to provide free, live, online technical support to assist you with any

questions you may have about installation, setup, troubleshooting, or product

recommendations. If you ever need assistance with your new product, please come online

to talk to one of our friendly and knowledgeable Tech Support Associates. Technical

support is available through the online chat button on our website www.monoprice.com

during regular business hours, 7 days a week. You can also get assistance through email by

sending a message to [e-mail]

SPECIFICATIONS

VESA® is a registered trademark of the Video Electronics Standards Association.

8