Page 1
Page 2
SAFETY WARNINGS AND GUIDELINE S
• Do not expose this device to water or moisture of any kind. If this device gets
wet, turn it off immediately and do not attempt to use it again until it is thoroughly
dried, inside and out.
• Do not disassemble or attempt to repair or modify this unit.
• Do not use this device while operating a motor vehicle, heavy equipment, walking
in traffic, or any other situation in which situational awareness is a key to safety.
• Clean only using a soft, dry cloth. For stubborn dirt, slightly moisten the cloth with
warm water.
• This device contains a rechargeable battery and electronic circuits. It should only
be disposed of in accordance with local laws and regulations.
PRODUCT OVERVIEW
1. Headband
2. Headband adjustment
3. Previous track button
4. Micro USB charging port
5. Multi-Function button
6. Next track button
7. Microphone
8. Earpieces
9. Power switch
10. Volume down/- button
11. Volume up/+ button
Page 3
OPERATION
Charging
Perform the following steps to charge built-in rechargeable battery prior t o use and
whenever the battery level is low:
• Ensure that the headphones are powered OFF.
• Plug one end of the included USB cable into the charging port on the
headphones and the other end into a USB power source, such as a computer,
wall charger, backup battery pack, etc.
• Depending on the current level of your USB power source, it can 2-3 hours to
fully charge the headphones. The LED indicator will glow red during charging.
• When charging is complete the LED indicator will glow blue.
Power
• Power ON the headphones by sliding the Power Switch (9) until a beep sounds
in the earpieces and the LED indicator begins flashing blue.
• Power OFF the headphones by sliding the Power Switch (9) until a beep sounds
in the earpieces and the LED indicator flashes blue twice.
Bluetooth Pairing
1. Ensure that both the headphones and your phone are powered ON.
2. Ensure that the headphones and the phone are within about 3 feet of each other.
3. Press and hold the Multi-Function button (5) on the headsets until the LED
indicator glows blue steadily.
4. Ensure that the Bluetooth feature on your phone is enabled. Perform a search for
Bluetooth devices and select the headphones from the list.
5. If asked for a passkey, enter 0000.
6. If pairing is successful, the LED indicator will rapidly flash blue 10 times, then will
flash once every 3 seconds.
7. If pairing is unsuccessful, the LED indicator will remain steady blue.
8. If no Bluetooth connection is established within about 60 seconds, the Bluetooth
pairing mode will turn off and the LED indicator will turn of f, as well.
Page 4
Disconnecting
Any of the following actions will break the Bluetooth connection between your phone
and the headphones:
• Turn headphones OFF
• Disconnect the headphones from the Bluetooth list on your phone.
• Move the phone at least 32 feet (10 meters) from the headphones.
Reconnecting
If your phone has previously been paired with the headphones, you can reestablish the
connection using one of the following methods:
• Press the Multi-Function button (5) once to automatically reconnect.
• With the headphones powered on, select the headphones from the list of
available Bluetooth devices on your phone.
Music Playback
• Press the Multi-Function button (5) to play or pause music.
• Press the Next Track button (6) to skip ahead to the next track.
• Press the Previous Track button (3) to skip back to the beginning of the current
track. If already at the beginning, pressing the Previous Track button will skip
back to the beginning of the previous track.
Volume Control
Press the Volume Up/+ (11) and/or Volume Down/- (10) buttons to control the volume
level. You can hold down the button for continuous volume adjustment rather than
repeatedly pressing the button to adjust the volume in steps.
Page 5
Answering or Rejecting an Incoming Call
When an incoming call is detected, your phone will automatically pause music playback
and the ringtone will sound in the earpieces.
• To answer the call, press the Multi-Function button (5) once.
• To reject the call, press and hold the Multi-Function button (5) for about 2
seconds. Music playback will automatically resume when a call is rejected.
Ending a Call
Press and release Multi-Function button (5) once. Music playback will automatically
resume when the call is ended.
Placing a Call on Hold*
• While the call is active, press and hold the Multi-Function button (5) f or about 2
seconds to place the call on hold.
• To resume a call on hold, press and hold the Multi-Function button (5) for about 2
seconds.
Redialing the Previous Number*
Press and hold the Multi-Function button (5) for about 2 seconds until you hear a long
beep. The previously dialed number will be redialed.
*Note that the Call Hold and Last Number Redialing features are functional only if your
phone supports those features.
Loading...