Monogram ZX2201NSS Installation Manual
GE Consumer & Industrial Appliances
Assembly Instructions
Advantium®Built-In Accessory Storage Drawer
JX2200, JX2201, ZX2201
MFL06213304 49-40594 12-08 JRSPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
BEFORE YOU BEGIN
Read these instructions completely and carefully. Read
the Installation Instructions for the Advantium 120V or
240V oven completely and carefully for cutout dimensions and step-by-step instructions.
IMPORTANT— Save these instructions for
local inspector’s use.
IMPORTANT— Observe all governing codes
and ordinances.
•
NOTE TO INSTALLER: Be sure to leave these
instructions with the Consumer.
•
NOTE TO CONSUMER: Keep these instructions with
your Advantium 120V or 240V Oven Owner’s Manual
for future reference.
•
SKILL LEVEL: Installation of this appliance requires
basic mechanical skills.
•
COMPLETION TIME: One hour with the installation
of an Advantium 120V or 240V oven.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty. See the Advantium
120V or 240V Oven Owner’s Manual for warranty
information.
TOOLS REQUIRED
• #2 Phillips screwdriver
PARTS SUPPLIED
• Side supports (2)
• Brass screws (8)
• Color-matched screws (5)
MODELS AVAILABLE
Profile Models:
JX2200BB–Black
JX2201SS–Stainless Steel
Monogram Models:
ZX2201SS–Stainless Steel (for installation above 36″ only)
NOTE: Advantium 240V model ZSC2202SS and
Advantium 120V model ZSC1202 CANNOT be
installed with an accessory storage drawer. See
Installation Preparation Without an Accessory Storage
Drawer in the Installation Instructions for these models.
PRODUCT DIMENSIONS AND CLEARANCES
Allow 15” Clearance
When Fully Open
5”
REMOVE PACKAGING AND PARTS
• Remove the drawer from the carton.
• Remove all packing material and tape.
• Open the drawer and remove any parts inside.
• Locate parts.
1
Assembly Instructions
Side Supports (2)
Under-the-Counter (UTC)
Mounting Bracket
Color-Matched
Screws
(4 required,
1 extra)
Screws
(6 required,
2 extra)
NOTE: Appearance will vary by model.
• Under-the-Counter
Mounting Bracket (1)
2
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN
Printed in Korea
UNDER-THE-COUNTER (UTC)
MOUNTING BRACKET INSTALLATION
NOTE: For UTC models PSB1200, PSB1201 and
ZSC1201 only.
Open the accessory drawer so you have access
to the top bracket.
Remove the three screws securing the top bracket.
Install the new UTC mounting bracket using the
screws removed previously.
Close the drawer and proceed with
the installation.
2
D
C
B
A
ASSEMBLING THE OVEN TO DRAWER
Place storage drawer on a surface with the front
of drawer hanging over the edge of the surface.
Not placing the front edge of drawer over the edge
of the surface may result in damage to the drawer
since the front edge of drawer hangs below the
bottom of drawer.
Place the oven on top of the storage drawer. Make
sure that the back and sides of the oven align with
the back and sides of drawer.
NOTE: The bottom of the oven side flanges will sit
directly in front of the top of the storage drawer
side flanges.
B
A
3
ASSEMBLING THE OVEN TO DRAWER
(cont.)
Remove the front two bottom screws on each side
of the oven and the top center screw on each side
of the storage drawer.
Place the side supports into the tabs on the drawer
and secure using the screws supplied and the
screws removed in Step C.
The oven and storage drawer assembly is now
ready to be installed. Return to the Advantium 120V
or 240V Built-In SpeedCook Oven Installation
Instructions to complete the installation.
C
E
D
Side
Support
120v only
Loading...