Monogram ZWL1126SJ Installation Instructions Manual
Installation
Instructions
Monogram
Drawer Microwave
For Models:
ZWL1126SJ
49-40754
(04-15 GE)
Installation Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT³ Save these instructions for
local inspector’s use.
IMPORTANT³ Observe all governing codes
and ordinances.
Note to Installer³ Be sure to leave these
instructions with the Consumer.
Note to Consumer³ Keep these instructions
with your Owner’s Manual for future reference.
Skill Level³ Installation of this appliance
requires basic mechanical and electrical skills.
Proper installation is the responsibility of
the installer. Product failure due to improper
installation is not covered under the warranty. See
Owner’s Manual for warranty information.
IMPORTANT
purpose. Never use the oven for warming or
heating a room. Prolonged use of the oven without
proper ventilation can be hazardous.
WARNING
not followed exactly, a fire or electrical shock may
result that could cause property damage, personal
injury or death.
Use this oven only for its intended
If the information in this manual is
WARNING
drawer may result in serious injuries and can also
cause damage to the Drawer Microwave.
Do not use the Drawer Microwave as a storage
space. This creates a potentially hazardous
situation.
&KHFNWKDWWKHWLPHRIGD\LVLQWKHGLVSOD\,IQRW
touch Stop/Clear to prevent unintended use.
Stepping, leaning or sitting on the
UNPACK DRAWER MICROWAVE
Remove all packing materials from inside the
Drawer Microwave. DO NOT REMOVE THE
WAVEGUIDE COVER, which is located on the top of
the Drawer Microwave.
Remove the feature sticker, if there is one. Check
the drawer for any damage, such as misaligned or
bent drawer, damaged drawer seals and sealing
surfaces, broken or loose Drawer Microwave guides
and dents inside the cavity or on the front side of
the drawer. If there is any damage, do not operate
the Drawer Microwave and contact your dealer.
Sealing Surface
WARNING
Drawer Microwave must be secured by a properly
installed Anti-Tip block.
7KLV'UDZHU0LFURZDYHPXVWEHHOHFWULFDOO\
grounded in accordance with local codes.
0DNHVXUHWKHZDOOFRYHULQJVDQGWKHFDELQHWV
around the Drawer Microwave can withstand the
heat generated by the Drawer Microwave.
WARNING
or unattended in the area where a Drawer
Microwave is in use. Never leave the drawer open
when the microwave is unattended.
To reduce the risk of tipping, the
Never leave children alone
Waveguide Cover
Sealing Surface
Oven Cavity
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
2
Installation Instructions
CLEARANCES AND DIMENSIONS
Dimensions that are shown in Figure 1 (for
24”) must be used. Given dimensions provide
minimum clearance. Locate electrical outlet in the
shaded area in the upper left-hand corner of the
cutout. See Figure 4.
Contact surface must be solid and level. Pay
special attention to the floor on which the Drawer
Microwave will sit. The floor of the opening
should be constructed of plywood strong enough
to support the weight of the oven (about 100
pounds).
Check location where the Drawer Microwave will
be installed for proper electrical supply.
Your oven can be built into a cabinet or wall by
itself or under a gas, under an electric wall oven,
or under selected cook top models. See use and
care manual for list of models.
Be sure that the clearance of the floor between
the wall oven and the drawer microwave is a
minimum of 2-inches.
The microwave interior will easily accommodate
a 9” x 13” oblong dish or a bag of microwave
popcorn.
The oven can also be mounted flush. Please see
instructions for flush mounting included with the
Flush Mount Deflector vent.
24” DRAWER MICROWAVE MEASUREMENTS
(Continues)
overlap
7
overlap
1
18
RIÀRRU
(6”)
13
14
/16”
opening
/16”
/2” to top
Figure 1
Anti-Tip
Block
3 1/2”
14 13/16”
to bottom
of Anti-Tip
Block
Floor must
support
100 lbs.
Suggested electrical
outlet location*
Allow
overlap
36”
countertop
height
22
opening
7
/8”
cabinet min.
1
/8”
24”
1
/2”
23
min
depth
4”
5”
Allow
7
/8”
overlap
Allow 3/16”
Allow
24” DRAWER MICROWAVE MEASUREMENTS
Figures 1 and 2 contain many drawer microwave
measurements for reference when planning the
drawer location.
This drawer microwave can be installed below any
electric or gas wall oven or under selected cook top
models. See use and care manual for list of models.
Can also be installed using an electrical outlet in
an adjacent cabinet within the areas where the
provided electrical cord can reach. Power cord
access hole in cabinet should be a minimum of 1
1/2” diameter hole and deburred of all sharp edges.
IMPORTANT
Always check electrical codes for requirements.
Always allow sufficient power cord
length to the electrical outlet to
prevent tension.
15
4 11/16”
3
/4”
1
4”
15
/16”
23 7/8”
21
5
/8”
15”
auto drawer
opening
14 19/32”
21 7/8”
1 1/4”
door thickness
Figure 2
3
Installation Instructions
ANTI-TIP BLOCK
NORMAL INSTALLATION STEPS
Anti -Tip BLOCK Installation Instructions
To reduce the risk of tipping of the drawer, the
Anti-Tip block must be properly installed located 14
13/16-inches above the floor on which the Drawer
Microwave will sit. The 6-inch Anti-Tip block must
be provided by the installer. See Figures 1 and 2.
The Anti-Tip block prevents serious injury that might
result from spilled hot liquids.
If the Drawer
Microwave is
ever moved to a
different location,
the Anti-Tip block
must also be moved
and installed. When
installed to the wall,
make sure that the
screws completely
penetrate the dry
wall and are secured in wood or metal so that the
block is totally stable. When fastening, be sure that
the screws do not penetrate electrical wiring or
plumbing
6”
Figure 3
Anti-Tip
block
1
/2”
3
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an
electrical short circuit, grounding reduces the risk
of electric shock by providing an escape wire for
the electric current. This appliance is equipped with
a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet
that is properly installed and grounded.Consult a
qualified electrician or serviceman if the grounding
instructions are not completely understood, or if
doubt exists as to whether the appliance is properly
grounded.
WARNING
Improper use of
the grounding plug
can result in a risk of
electric shock.
Do not use an
extension cord. If the
power supply cord
is too short, have a
qualified electrician
or serviceman install
an outlet near the
appliance.
Permanent and Correct Installation
3-Prong plug
Grounding pin
3-Prong receptacle
Grounded receptacle box
ELECTRIC OUTLET
The electrical requirements are a 120 volt 60 Hz, AC
only, 15 amp. or more protected electrical supply.
It is recommended that a separate circuit serving
only this appliance be provided.
The drawer is equipped with a 3-prong grounding
plug. It must be plugged into a wall receptacle that
is properly installed and grounded. Should you only
have a 2-prong outlet, have a qualified electrician
install a correct wall receptacle.
Note: If you have any questions about the
grounding or electrical instructions, consult a
qualified electrician or service person.
* Can also be installed using an electrical outlet
in an adjacent cabinet within the area where the
provided electrical cord can reach. Always check
electrical codes for requirements.
Suggested electrical
outlet location*
T
5”
4”
Figure 4
DRAWER INSTALLATION
Mounting
Flange
Figure 5
1. Place the drawer adjacent to the wall or cabinet
opening. Plug the power supply cord into the
electrical outlet.
2. Carefully guide the drawer into the prepared
opening. Avoid pinching the cord between the oven
and the wall.
3. Slide the drawer all the way until the mounting
flange is flush with the face of the cabinet. See
Figure 5.
4. Open the drawer. Using the
4 holes on the drawer as a
template, pre drill the cabinet
using a 1/16” bit. See Figure 5.
5. Secure the drawer with the 4
screws supplied.
Parts supplied
4 Screws
4
Installation Instructions
24” Flush Mount Deflector Vent
IMPORTANT NOTES TO THE INSTALLER
Read all of the Installation Manual that is included
with the Drawer Microwave before installing in
the flush mount configuration.
PARTS INCLUDED
Qty Description
1 Flush Mount
'HÀHFWRU9HQW
Observe all governing codes, ordinances, and
safety instructions.
Be sure to leave this installation with the
consumer.
2 Mounting Screws
1. Prepare cabinet opening as shown in Figures 6, 7, 8, and 9.
Suggested Electrical
Outlet Location*
24
24
3
1
/16”
1
3
/16” min
1
7
/8”
/2” max
4”
22”
23
min depth
6”
Anti-Tip Block
1
3
5”
7
16
1
/2”
/8”
Opening
/2”
13
/16”
14
to bottom
of Anti-Tip
Block
Floor must
support
100 lbs
NOTE: the face of the shelf
must sit 1
Shelf Face
7
/8” back from the
face of the cabinet.
7
1
/8”
Cabinet Face
Figure 6
5
Loading...