Monogram ZWE23E, ZWE23P Installation Instructions Manual

Installation
Instructions

Double-Door, Bottom-Drawer
Free-Standing Refrigerator

Français

For a French version of this manual, visit
our Website at monogram.com.

Pour la version française de ce manuel, visitez
notre site Web sur monogram.com

Español

For a Spanish version of this manual, visit
our Website at monogram.com.

Para consultar una version en español de
este manual de instrucciones, visite nuestro
sitio de internet monogram.com.

monogram.com

Safety Information

BEFORE YOU BE GIN

Read these in struc tions completely and carefully.

IM POR TANT – Save these instructions for

•
local inspector’s use. Observe all gov ern ing codes and
ordinances.

Note to In stall er – Be sure to leave these

•
instructions with the Consumer.

• Note to Con sum er – Keep these instructions with
your Owner’s Manual for future reference.

WARNING

exercise basic safety precautions, including the following:

• This appliance must be properly ground ed. See
“Ground ing the Refrigerator,” page 6.

• Use this appliance only for its intended pur pose.

• Immediately repair or replace electric service cords that

become frayed or damaged.

• Unplug the refrigerator before cleaning or making

repairs.

• Repairs should be made by a qualified service

technician.

• To reduce the risk associated with choking, do not

allow children under 3 years of age to have access to
small parts during the installation of this product.

When using this appliance, always

Skill Level – Installation of this refrigerator requires

basic me chan i cal, carpentry and plumbing skills. Proper
installation is the re spon si bil i ty of the installer. Product
failure due to improper installation is not covered under
the GE Appliances Warranty. See the Owner’s Manual
for warranty information.

If you received a damaged refrigerator, you should
immediately contact your dealer or builder.

CAUTION

Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to
the product – TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.

For Monogram local service in your area, call 1.800.444.1845.
For Monogram service in Canada, call 1.800.561.3344
For Monogram Parts and Accessories, call 1.800.626.2002.
www.monogram.com

CONTENTS

Planning Information

Product Dimensions and Clearances ...........................4

Installation Instructions

Tools, Hardware, Materials .........................................6

Grounding the Re frig er a tor ......................................... 6

Step 1. Measure Cabinet Opening ..............................7

Step 2. Install Anti-Tip Bracket ....................................7

Step 3. Install the Refrigerator ....................................8

Step 4. Remove the Freezer Drawer ..........................9

Step 5. Remove the Fresh Food Doors ......................9

Step 6. Move the Refrigerator ...................................10

Step 7. Replace the Freezer Drawer ........................11

Step 8. Leven the Freezer Drawer .............................11

Step 9. Replace Fresh Food Doors ..........................12

Step 10. Install Water Line ........................................12

Step 11. Connect Water Supply ................................13

Step 12. Plug in the Refrigerator ...............................13

Step 13. Level the Refrigerator .................................13

Step 14. Level Doors .................................................14

Step 15. Remove Packaging, Start Icemaker ...........14

Step 16. Temperature Controls ..................................14

2

Information de sécurité/ Información de seguridad

AVERTISSEMENT

réfrigérateur, observez toujours certaines précautions de
base, notamment :

Este electrodoméstico deberá estar conectado a tierra

•

de forma adecuada. Consulte “Cómo Conectar a Tierra
el Refrigerador”, página 6.

• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.

• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.

• Il faut débrancher le réfrigérateur avant le nettoyage ou
toute intervention.

• Les réparations doivent être faites par un technicien
qualifié.

• Pour réduire le risque d’étouffement pendant

l’installation de ce produit, ne pas laisser les petites
pièces à la portée des enfants âgés de moins de 3 ans.

ADVERTENCIA

pre siga las precauciones básicas de seguridad, incluyen­do lo siguiente:

• Este electrodoméstico deberá estar conectado a tierra

de forma adecuada. Consulte “Cómo Conectar a Tierra
el Refrigerador”, página 6.

• Use este electrodoméstico sólo para su propósito
original.

• De forma inmediata, repare o reemplace los cables del
servicio eléctrico que sufran daños o peladuras.

• Desenchufe el refrigerador antes de realizar su limpieza
o reparaciones.

• Cualquier reparación deberá ser realizada por un
técnico calificado del servicio técnico.

• A fin de reducir el riesgo asociado con asfixia, no

permita que los niños menores de 3 años tengan
acceso a las partes pequeñas durante la instalación de
este producto

Lorsque vous utilisez le

Al usar este electrodoméstico, siem-

ATTENTION

À cause du poids et de la taille de ce réfrigérateur et pour
réduire le risque de blessure et de dommages, IL FAUT
DEUX PERSONNES POUR FAIRE L’INSTALLATION
CORRECTEMENT.

PRECAUCIÓN

de este refrigerador, y a fin de reducir el riesgo de
lesiones personales o daños sobre el producto - SE
DEBERÁ CONTAR CON DOS PERSONAS PARA UNA
INSTALACIÓN ADECUADA.

Debido al peso y tamaño

3

Planning Information

PRODUCT DIMENSIONS AND CLEARANCES ZWE23E Models

28 11/16"

36" (91.4)

37 1/2"

(95.25)

30 7/16"

(77.3)

24 3/8"

(61.9)

FRONT VIEW SIDE VIEW

(91.4)

36"

Case width

70 1/2"

(179.1)

2"

(5.1)

2"

(5.1)

(91.4)

36"

Case width

(72.9)

24 3/8" (61.9)

13/16"

(2.1)

69 1/8"

(175.6)

SPECIFICATIONS

Overall Width 36" (91.4 cm)
Overall Height 70 1/2" (179.1 cm)
Overall Depth 30 11/16" (76.2 cm)
Door Clearance 21 1/4" (54 cm)
Cutout Width 36 1/4" (92.1 cm)
Cutout Height 71" (180.3 cm)
Cutout Depth 26 3/8" (67 cm)
Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 400 lb (181.4 kg)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.

Air Circulation Clearances:

• 1/8” on each side

• 2” at the back side

• 1” at top (cabinet/hinge cover)

*11 11/16"

(29.7)

*11 11/16"

(29.7)

*124° Door swing

TOP VIEW

(SHOWING DOOR SWING)

18"

(45.7)

TOP VIEW

(FREEZER DOOR OPEN)

21 1/4"

(53.9)

4

Planning Information

PRODUCT DIMENSIONS AND CLEARANCES ZWE23P Models

28 11/16" (72.9)

36" (91.4)

37 1/4"

(94.6)

23 3/4"

(60.3)

FRONT VIEW SIDE VIEW

36" (91.4)

Case width

70 1/2"

30 1/2"

(77.5)

2 13/16"

(7.1)

(179.1)

2"

(5.1)

24 3/8" (61.9)

36" (91.4)

Case width

13/16"

(2.1)

69 1/8"

(175.6)

SPECIFICATIONS

Overall Width 36" (91.4 cm)
Overall Height 70 1/2" (179.1 cm)
Overall Depth 31 1/2" (78.7 cm)
Door Clearance 22 1/8" (56.2 cm)
Cutout Width 36 1/4" (92.1 cm)
Cutout Height 71" (180.3 cm)
Cutout Depth 26 3/8" (67 cm)
Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 400 lb (181.4 kg)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.

*12 7/16"

(31.6)

*124° Door swing

TOP VIEW

(SHOWING DOOR SWING)

*12 7/16"

(31.6)

18"

(45.7)

TOP VIEW

(FREEZER DOOR OPEN)

22 1/8"

(56.2)

5

Installation Instructions

TOOLS REQUIRED

• Adjustable wrench

• 3/8” socket ratchet/driver

• Phillips head screwdriver

• Flat-Head ScrewdriveR

• 5/32”, 3/32”, 1/8”, 1/4” Allen wrenches

• 1/8” Drill bit and electric or hand drill

• Tape measure

• Pencil

• Wire cutters

• 1/4” Nut driver

• Level

• Torx T20, T25

MATERIALS REQUIRED

• 1/4” O.D. compression nut and 2 ferrules (sleeves)
OR SmartConnect™ Refrigerator Tubing Kits

GROUNDING THE REFRIGERATOR

IMPORTANT – (Please read carefully)

FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall receptacle to minimize the pos­sibility of electric shock hazard from this appliance.

FLOORING

For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should be
strong enough to support a fully loaded refrigerator.

IMPORTANT NOTE: Protect the finish of the flooring.
Cut a large section of the cardboard carton and place
under the refrigerator where you are working.

DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG OUTLET.

Have the wall outlet and circuit checked by a qualified
elec tri cian to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is en coun tered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.

DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.

6

Installation Instructions

WARNING

Under certain
circumstances, this
refrigerator can tip forward.

Injury to persons can result.
Install Anti-Tip Bracket packed with this

refrigerator.

AVERTISSEMENT

Dans certaines circonstances,
ce réfrigérateur peut basculer
vers l'avant.

Cela présente un risque de blessure aux personnes.
Veuillez poser la ferrure anti-basculement emballée avec

le réfrigérateur.

ADVERTENCIA

Bajo ciertas circunstancias,
este refrigerador se puede
caer hacia adelante.

Puede haber personas lesionadas como resultado
de esto.

Instale el soporte antivolcaduras, incluido con este
refrigerador.

STEP 1 MEASURE CABINET
OPENING AVAILABLE VS.
REFRIGERATOR WIDTH

Measure width of cabinet opening where
refrigerator will be placed, W.

Be sure to account for any countertop overhang,
baseboard thickness and any clearance desired.
Width, W, should not be less than 36 inches. The
refrigerator will be placed approximately in the
middle of this opening.

Rear Wall

W

REFRIGERATOR

Baseboard
Thickness
or Countertop
Overhang
(Whichever
is Greater) Plus
Any Desired
Clearance

RH Side

STEP 2 LOCATE ANTI-TIP
BRACKET

A. Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor up
against the rear wall, within W, and in line with the

Figure 1 – Installation Overview

Floor – Concrete
(2 Holes)

Floor – Wood
(2 Holes)

Base Bracket
on the
Refrigerator

desired location of the RH side of the refrigerator
(see Figure 1).

B. Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with
the floor holes indicated on the template sheet,
approximately 15-1/4” from the edge of the sheet or
the RH side of the refrigerator.

C. Hold down in position and use the anti-tip floor

bracket as a template for marking the holes based
upon your configuration and type of construction
as shown in Step 3. Mark the hole locations with a
pencil, nail or awl.

NOTE: It is REQUIRED to use at least 2 screws

to mount the floor bracket (one on each side of the
anti-tip floor bracket). Both must be into either the
wall or the floor. Figure 2 indicates all the acceptable
mounting configurations for screws. Identify the
screw holes on the anti-tip floor bracket for your
configuration.

2 Wall Holes

15 ¼”

RH Side of
Refrigerator

Floor Bracket
to Install

RH Holes

Rear RH
Corner of
Cabinet Wall

Locator
Template Sheet

Front

7

Installation Instructions

STEP 2A LOCATE ANTI-TIP FLOOR

BRACKET (CONT.)

Figure 2 – Acceptable Screw

Placement Locations

Preferred Installation –

Wood

Minimum Acceptable #1 –

Wall Plate Stud

Minimum Acceptable #3 –

Concrete Floor

Preferred Installation –

Concrete

Minimum Acceptable #2 –

Wood Floor

STEP 2B INSTALL ANTI-TIP

BRACKET (CONT.)

CONCRETE Wall and Floor Construction:
A. Anchors required (not provided):

4 each 1/4” x 1 1/2” lag bolts
4 each 1/2” O.D. sleeve anchors

B. Drill the recommended size holes for the anchors

into the concrete at the center of the holes marked
in Step 2.

C. Install the sleeve anchors into the drilled holes.

Place the anti-tip floor bracket as indicated in Step

2. Remove the locator template from the floor.

D. Install the lag bolts through the anti-tip floor bracket

and tighten appropriately.

WOOD Wall and TILE Floor Construction:
A. For this special case, locate the 2 wall holes

identified in Fig. 2. Drill an angled 1/8” pilot hole
(approx. as shown in Fig. 3) in the center of each
hole.

B. Mount the anti-tip floor bracket using the Minimum

Acceptable Installation #1, as illustrated in Fig. 2.

STEP 2B INSTALL ANTI-TIP

BRACKET

WOOD Wall and Floor Construction:
A. Drill the appropriate number of 1/8” pilot holes in the

center of each floor bracket hole being used (a nail
or awl may be used if a drill is not available) AND
remove the locator template from the floor.

B. Mount the anti-tip floor bracket by fastening the 2,

or preferably 4, #10-16 hex-head screws tightly into
place as illustrated in Figure 3.

Figure 3 – Attachment to

Wall and Floor

Rear RH Corner

of the Refrigerator

Floor Bracket

2 Screws Must

Enter Wood

or Metal Stud

Floor

Wall

Wall

Plate

Stud

STEP 2C POSITION THE

REFRIGERATOR TO
ENGAGE THE ANTI­TIP FLOOR AND BASE
BRACKETS

A. Before pushing the refrigerator into the opening,

plug the power cord into the receptacle and connect
waterline (if equipped). Check for leaks.

B. Locate the refrigerator’s RH side and move back

approximately in line with the RH side of the cabinet
opening, W. This should position the anti-tip floor
bracket to engage the anti-tip base bracket on the
refrigerator.

C. Gently roll the refrigerator back into the cabinet

opening until it comes to a complete stop. Check to
see if the refrigerator front lines up with the cabinet
front face. If not, carefully rock the refrigerator
forward and backward until engagement occurs and
you notice thatthe refrigerator is fully pushed up
against the rear wall.

D. OPTIONAL: Adjust the rear (and front) wheel height

settings to fully engage the rear anti-tip brackets,
while also aligning the refrigerator front with the
cabinet front face.

NOTE: If you pull the refrigerator out and away from
the wall for any reason, make sure the anti-tip floor
bracket is engaged when the refrigerator is pushed
back against the wall rear wall.

8

Installation Instructions

STEP 3 INSTALL THE

REFRIGERATOR BEFORE
MOVING REFRIGERATOR
INDOORS

IMPORTANT: Doors and passageways into the

installation location require a 31-1/4” min. opening. If
the opening is less than 31-1/4”, the top cap, doors and
drawers must be removed. (See steps 4–6.)

NOTE: Skip steps 4–5 if door removal is not required.
Go to page 10, Move The Refrigerator.

NOTE: To prevent damage, leave inside
packaging, door spacer and outside protective
wrap in place until the unit is moved to the
installation location.

STEP 4 REMOVE THE FREEZER

DRAWER

The freezer drawer can be removed, if needed, to fit
through tight areas.

Read these instructions completely and carefully.
A. Pull the freezer door open to full extension.
B. Remove 3 attachment screws, located at the bottom

on each side of the freezer door using 3/8” hex
socket driver.

STEP 5 REMOVE THE FRESH

FOOD DOORS

A. Securely tape the door shut with masking tape or

have a second person support the door.

B. Start with left-hand door first: Remove the hinge

cover on top of the left refrigerator door by removing
all hex screws and pulling it up. Do the same for the
right-hand door and the middle cover.

Hinge
Cover

C. Disconnect both electrical connectors at the top

cover.

CAUTION

Freezer door is heavy Use both hands to secure the
door before lifting.

ATTENTION

La porte du compartiment congélateur est lourde. Utilisez
les deux mains pour stabiliser la porte avant de la soulever.

PRECAUCIÓN

La puerta del freezer es pesada. Use ambas manos para
asegurar la puerta antes de levantar la misma.

C. Lift the freezer door to disengage it from the slide

mechanism. The door can safely rest on the bot­tom. Do not rest the door on any other surfaces to
avoid scratches. Push the slide mechanism back
completely until it self retracts.

Lifting Hazard

Avertissement de porte lourde.

Riesgo al levantar la puerta

Remove the 1/4” hex head screw to disconnect the
ground wire from the hinge.
Remove the 1/4” hex head screw to remove the
strain relief from the water line.

Ground
screw

Strain
Relief

9

Installation Instructions

STEP 5 REMOVE THE FRESH

FOOD DOORS (CONT)

D. Disconnect the water line from the back of the unit

by pressing down on the dark grey collar while
pulling up on the water line.
Pull waterline through case conduit from the top to
free the line for door removal. The water line is more
than 4’ long and may need to be taped to Door for
accessibility when reinstalling.

E. Using a 3/8” socket ratchet/

driver, remove the screws
securing the top hinge to the
cabinet, then lift the hinge
straight up to free the hinge pin
from the location in the top of

the door.

CAUTION

Single person lift could cause injury. Use assis­tance when handling, moving or lifting the refrig­erator doors.

ATTENTION

lourde.

Le soulèvement de la porte par une seule personne
peut présenter un risque de blessure. Obtenir de l'as­sistance lors de la manipulation, du déplacement ou du

soulèvement des portes du réfrigérateur.

PRECAUCIÓN

Si es levantada por una sola persona, podrían ocasio­narse lesiones. Solicite ayuda al sostener, mover o

levantar las puertas del refrigerador.

Note: when removing door, to prevent damage to

door and electronics, carefully place the door in a
proper location.
Note: The lower door hinge pin and hinge are keyed
and must be matched correctly for the door to self
close properly. Please follow the directions carefully.

Lifting Hazard.

Avertissement de porte

Riesgo al levantar la puerta

STEP 5 REMOVE THE FRESH

FOOD DOORS (CONT)

Note: for proper installation later, please follow
the next step carefully.

F. Fresh Food doors to be REMOVED and

INSTALLED opened at 90° with case front.

REMOVE OPPOSITE DOOR

Follow the same procedure on the opposite door.
There are no wires or water lines on the opposite
side.

G. REMOVE CENTER HINGE (if necessary)

5HPRYHWKHƎVFUHZVVHFXULQJWKHFHQWHUKLQJHWRWKH

cabinet. Use T20 driver to remove outboard screw.

Remove
center screw

Loosen Outer screws

STEP 6
MOVE THE REFRIGERATOR

• Place a piece of the carton or soft cloth against the
side panel of the refrigerator to pad and protect the
stainless steel finish.

• Place the refrigerator on the handtruck with a side
against the truck only.

• Move the refrigerator indoors. Place refrigerator
close to the installation location.

10

Installation Instructions

STEP 7 REPLACE THE FREEZER

DRAWER

ATTACH AND SECURE THE DRAWER FRONT
TO THE SLIDES

A. Pull the slide Mechanism to full extension using both

hands simultaneously.

B. Remove the basket resting on the slides.

CAUTION

Freezer door is heavy Use both hands to secure
the door before lifting.

ATTENTION

lourde.

La porte du compartiment congélateur est lourde.
Utilisez les deux mains pour stabiliser la porte avant
de la soulever.

Lifting Hazard

Avertissement de porte

STEP 8 LEVEL THE FREEZER

DRAWER

A. Locate the height adjuster cam in the freezer

door. Slightly loosen the three door attachment
screws on both sides using a 3/8” hex socket
driver.

B. Locate and loosen the cam screw using the

T-27 screw driver.

Cam
Screw

PRECAUCIÓN

La puerta del freezer es pesada. Use ambas manos
para asegurar la puerta antes de levantar la misma.

C. Lift the freezer door and place it on the slide

mechanism

D. Replace the attachment screws and torque the

screws to 65 in-lb

E. Adjust freezer door gap if necessary.

Riesgo al levantar la puerta

Align and insert tab on
freezer door bracket
into slot on freezer slide
bracket.

C. Lift the door on the side requiring adjust-

ment, rotate the cam to required position.

0 - Initial position
1 - Lift by 0.050”

-1 - Lower by 0.050”

-2 - Lower by 0.100

-3 - Lower by 0.150”

D. After adjustment tighten the 3 attachment

screws using to 65 in-lb.

11

Installation Instructions

STEP 9 REPLACE FRESH FOOD

DOORS

A. Reinstall center hinge first and torque the

screws to 65 in-lbs. With the LH door at 90º to the

front ofthe case, lower the refrigerator door onto the
center hinge. Ensure that the door and hinge align
correctly.

B. Rotate door closed and make sure moveable center

sealing portion of the door aligns with the striker. If

the door will not self-close after reinstalling, remove
door, turn door upside down, check alignment mark
and arrow; (there is an alignment mark on the door
closure mechanism It corresponds to an alignment
mark on the bottom end cap. Rotate door closure
mechanism to align mark and arrow, reinstall door).

Underside of
Fresh Food Door

Align marks

align marks

If door cannot be installed at 90° follow steps below:

1. If space or model limits opening door to less than 180°, then:
a) Remove door, carefully turn door upside down.
b) Check alignment of door closure mechanism shaft on
underside of door. The flats on the shaft should correspond
to alignment tab on plastic ring or mark on bottom end cap.
c) If shaft is not aligned to tab/mark, using 5/32” Allen
wrench, rotate door closure mechanism shaft
counterclockwise for right door and clockwise for left door.
Then align flat with tab/mark.
d) Install the door at 90°.

Securely tape the door shut with masking tape or
have a second person support the door. Reinstall
the top hinge and torque the screws to 65 in-lbs.

C. Be sure to reinstall the ground wire and strain relief

to the top hinge.

D. Reinstall the hinge cover. Note: Ensure wires are

not pinched or under screw bosses before tightening
screws.

E. Follow the same procedure on the opposite door.

STEP 10 INSTALL WATER LINE

Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are
SmartConnect™ Refrigerator Tubing (WX08X10006,
WX08X10015 and WX08X10025).

When connecting your refrigerator to a Reverse
Osmosis Water System, the only approved installation
is with a GE Appliances RVKit. For other reverse
osmosis water systems, follow the manufacturer’s
recommendations.

If the water supply to the refrigerator is from a Reverse
Osmosis Water Filtration System (RO)AND the
refrigerator also has a water filter, use the refrigerator’s
filter bypass plug. Using the refrigerator’s water
filtration cartridge in conjunction with an RO water filter
can result in hollow ice cubes. Some models do not
come equipped with the filter bypass plug. To obtain a
free bypass plug, call 800-GECARES. In Canada call

800.561.3344.
This water line installation is not warranted by the

refrigerator or ice maker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.

Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing the
water supply line to the refrigerator.

To prevent burns and product damage, do not hook up
the water line to the hot water line.

Do not install the ice maker tubing in areas where
temperatures fall below freezing.

When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.

All installations must be in accordance with local
plumbing code requirements.

• Copper or SmartConnect™ Refrigerator Tubing kit,
1/4” outer diameter to connect the refrigerator to the
water supply. If using copper, be sure both ends of
the tubing are cut square.

To determine how much tubing you need:
measure the distance from the water valve on the back
of the refrigerator to the water supply pipe. Be sure
there is sufficient extra tubing to allow the refrigerator
to move out from the wall after installation.

SmartConnect™ Refrigerator Tubing Kits are available
in the following lengths:

6’ (1.8 m) – WX08X10006
15’ (4.6 m) – WX08X10015
25’ (7.6 m) – WX08X10025

12

Installation Instructions

STEP 11 CONNECT WATER

SUPPLY

A cold water supply is required for automatic ice
maker operation. If there is not a cold water supply,
you will need to provide one. See Installing the Water
Line section.

NOTES:

• Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.

• If your refrigerator does not have a water filter,
we recommend installing one if your water supply
has sand or particles that could clog the screen of
the refrigerator’s water valve. Install it in the water
line near the refrigerator. If using SmartConnect™
Refrigerator Tubing Kit, you will need an additional
tube (WX08X10002) to connect the filter. Do not
cut plastic tube to install filter.

• Before connecting the water line to the house,
purge the house line for at least 2 minutes.

A. If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end
of the tubing coming from the house cold water
supply.

If you are using the SmartConnect™ tubing, the

nuts are already assembled to the tubing.

STEP 11 CONNECT WATER

SUPPLY (Cont.)

B. If you are using copper tubing, insert the end of

the tubing into the refrigerator connection, at the
back of the refrigerator, as far as possible. While
holding the tubing, tighten the fitting.

If you are using SmartConnect™ tubing, insert

the molded end of the tubing into the refrigerator
connection, at the back of the refrigerator, and
tighten the compression nut until it is hand tight.
Then tighten one additional turn with a wrench.
Over tightening may cause leaks.

C. Fasten the tubing into the clamp provided to hold it

in position. You may need to pry open the clamp.

D. Turn on the water at the shut-off valve to check

for leaks.

STEP 12 PLUG IN THE

REFRIGERATOR

See the grounding information
attached to the power cord.

SmartConnect™
Tubing

Refrigerator
Connection

1/4”
Compression Nut

Ferrule
(sleeve)

OR

STEP 13 LEVEL THE

REFRIGERATOR

The leveling legs have two purposes:

• Leveling legs adjust so the refrigerator is firmly posi­tioned on the floor and does not wobble.

• Leveling legs serve as a stabilizing brake
to hold the refrigerator securely in position during
operation and cleaning. The leveling legs also pre­vent the refrigerator from tipping.

Turn the leveling legs clockwise to raise the refrigera­tor, counterclockwise to lower it.

Raise

Flat-Head Screwdriver

NOTICE: To avoid possible property

damage, the leveling legs must be firmly
touching the floor.

13

Installation Instructions

STEP 14 LEVEL THE DOORS

Remember a level refrigerator is necessary for
getting the doors perfectly even. If you need
help, review the previous section on leveling the
refrigerator.

When
the left door
is lower than
the right
door.

A. If you open the freezer door, you can see the

center hinge.

B. Insert 1/4” Allen wrench into the shaft of the

center hinge.

C. Adjust the height by turning clockwise

or counterclockwise. When you turn
counterclockwise, the door will move up.

When
the left
door is
higher
than
the right
door.

Adjustment
point

STEP 15 REMOVE PACKAGING,

START ICEMAKER

Power Switch

A. Remove all tape, foam and protective packing from

shelves and drawers.

B. Remove the tie downs from the freezer baskets.
Set the icemaker power switch to the I (on) position.

The icemaker will not begin to operate until it reaches
its operating temperature of 15°F (–9°C) or below. It
will then begin operation automatically. It will take 2–3
days to fill the ice bin.

NOTE: In lower water pressure conditions, the water
valve may turn on up to 3 times to deliver enough
water to the icemaker.

STEP 16 TEMPERATURE
CONTROLS

• The temperature controls are preset at 37°F
for the refrigerator and 0°F for the freezer.

• Allow 24 hours to stabilize before making
adjustments.

RAISE

14