Monogram ZV800BJBB Specsheet

12

its

DIMENSIONS AND INSTALLATION INFORMATION
(IN INCHES)

NOTE

The vent hood canopy extends forward 5-7/8".

The vent hood must be installed 24" min., and 30" max.
above the cooking surface. The telescopic duct cover
conceals the ductwork running from the top of the hood
to the ceiling. The duct cover is sized to reach 8 ft. to 10 ft.
ceiling heights.

The hood installation height, from the cooking surface to
the bottom of the hood, depends upon ceiling height.

ZV800SJ/BJMONOGRAM 36" SLIDE-OUT HOOD

*Height to

Ceiling

1-1/2"

INSTALLATION INFORMATION

Before installing, consult installation instructions packed
with product, or available online at monogram.com, for
current dimensional data.

-15/16" at sides
13-11/16" at center

35-7/8"

*The Supplied Duct Cover F

8 ft. to 10 ft. Ceiling Heights

Listed by
Underwriters
Laboratories

Product Specification Revised 1/18

ZV800SJ/BJMONOGRAM 36" SLIDE-OUT HOOD

WALL MOUNT INSTALLATIONS

These hoods may be installed onto a wall or below
a wall cabinet.

• Telescopic duct covers are provided to conceal the

ductwork, running to the ceiling.

• This hood can be installed for recirculation operation.

No kits required.

24” Min.

30” Max.

INSTALLATION BELOW A CABINET

*20” Min.

24” Min.

* The cabinet must measure at least 20" from the bottom

frame to the inside top. The hood housing will occupy
the interior cabinet space.

INSTALLATION BELOW A WALL CABINET

Order a cabinet that is at least 20" high from the
bottom frame to the inside top. The cabinet must be
at least 12" deep.

• The hood installation height is determined by
the ceiling height.

• The hood installation height must be 24" Min. above the

cooking surface.

36” Min.

The vent hood must be installed 24" min. and 30" max.
above the cooking surface. The hood installation height,
from the cooking surface to the bottom of the hood,
depends upon ceiling height.

Listed by
Underwriters
Laboratories

Product Specification Revised 1/18

ZV800SJ/BJMONOGRAM 36" SLIDE-OUT HOOD

CABINET REQUIREMENTS

This hood may be installed beneath a wall-mounted
cabinet.

• Both vented and recirculating operation can be

accomplished in an under-cabinet installation.

• If the cabinet has been installed, it must be removed so

that wall framing supports can be added.

20” Min.

24” Min.

30” Max.

The cabinet must be at least 20" high between the
bottom frame and the inside top. A custom cabinet or
modifications to a dierent size cabinet may be required
to accommodate the hood housing.

• The cabinet must be 36" wide.

• The cabinet must be rmly secured to wall studs or

the added framing support and capable of supporting
100 pounds.

DUCTWORK, WIRING

• Determine the exact location of the vent hood.

• Locate the Rear Wall Template packed with the

literature.

• Measure 36" from the oor to the top of the cooking

surface. Add the pre-determined hood installation
height. Mark that location.

• Use a level to draw a straight pencil line on the wall.

3-3/4” centerline

to wall

Ceiling

Drill 1/8"

Drill 1/8"

Pilot Holes

Pilot Holes

Drill 1/8"
Pilot Holes

Drill 1/8"
Pilot Holes

5-1/16"

9-5/8"

11”

11-3/4”

19-1/2”

49-80271 JR 07-04

13-3/4"

12-3/4"

2-1/16"

C

L

REAR WALL TEMPLATE

Drill 1/8"
Pilot Holes

8-1/8"

Drill 1/8"
Pilot Holes

ALIGN BOTTOM EDGE WITH

PENCIL LINE INDICATING

BOTTOM OF THE HOOD.

• Tape the template in position along the penciled line.

Check to be sure the template is level.

• Use the level to draw a line straight up, from the

centerline on the template to the ceiling.

• Measure 3-3/34" from the back wall to the centerline
of a 6-1/2" hole on the ceiling.

NOTE

If drywall is not present, add drywall thickness to the
3-3/4" dimension.

HOUSE WIRING LOCATION

• The junction box is located on the top right side
of the hood.

• Wiring should enter the back wall 20" to 26" above
the bottom of the hood, and within 4" of the right
side of the centerline. Wiring should enter at least
4" above the bracket on the right side.

Listed by
Underwriters
Laboratories

Product Specification Revised 1/18

FEATURES AND BENEFITS

UNDER-CABINET OR STAND-ALONE INSTALLATION
The chimney hood installs beneath a cabinet, above
most cooktops and ranges. For a more contemporary
look, the system can be wall-mounted with matching
8-to-10-ft. duct cover

LOW-PROFILE DESIGN, HIGH-IMPACT STYLE
The retractable glass canopy is sleekly styled with a
streamlined design, seamlessly finished edges and
front-mounted touch controls

POWERFUL VENTILATION

A four-speed, 460-CFM fan blower with boost option

captures the smoke and steam produced by high­performance cooking equipment

MULTILEVEL HALOGEN LIGHTING
Six levels of intensity, from accent to ambient settings,
allow you to choose the lighting to match the cooking
task or occasion

ZV800SJ/BJMONOGRAM 36" SLIDE-OUT HOOD

EASY MAINTENANCE
Stainless steel filters can be easily removed for safe
cleaning in your dishwasher

RECIRCULATING KIT
Included for applications that do not
allow outside venting

Product Specification Revised 1/18