Monogram ZV48SSJSS Specifications

47 15/16"

12"

18"

47 15/16"25"

Soffit

Soffit Installation

30" min

36" max

Wall Mount Installation

30" min

36" max

DIMENSIONS AND INSTALLATION INFORMATION
(IN INCHES)

INSTALLATION CLEARANCES

These vent hoods are designed to be installed onto a
wall or beneath a sot or cabinet.

• Install these hoods* 30" Min. to 36" Max. above the

cooking surface.

* These hoods may be installed 24" min. above a gas or

electric drop-in style cooktop. Always observe the 30"
to 36" clearance when installed over any professional
style cooktop or range..

NOTE

Clearances may vary due to type of cooking product
and local codes. Check with local inspectors to be sure
standard is applicable.

ZV48SSJSSMONOGRAM 48" STAINLESS STEEL PROFESSIONAL HOOD

SOFFIT INSTALLATION WALL MOUNT INSTALLATION

In this installation, the ductwork running from the
top of the hood will be concealed in the sot or
upper cabinetry.

For this installation, a decorative duct cover is
available to conceal the ductwork running from
the top of the hood. Use of the duct cover requires
special consideration to the installation height above
the countertop.

Listed by
Underwriters
Laboratories

Product Specification Revised 1/18

ADVANCED PLANNING

Optional Duct Cover Accessories

6" Duct Cover

12" Duct Cover

DUCTWORK PLANNING

• These vent hoods are equipped for 10" round ductwork.
In most instances they may be transitioned to 8" round.

• This hood may be vented vertically through upper

cabinets, sot or ceiling. A duct transition piece is

supplied for vertical exhaust. Use locally supplied elbows
to vent horizontally through the rear wall.

• Determine the exact location of the vent hood.

• Plan the route for venting exhaust to the outdoors.

• Use the shortest and straightest duct route possible.
For satisfactory performance, duct run should not exceed
150 ft. equivalent length for any duct congurations.

• Refer to “Duct Fittings” chart to compute the maximum

permissible length for duct runs to the outdoors.

• Use metal ductwork only.

• Install a wall cap or roof cap with damper at the exterior

opening. Order the wall or roof cap and any transition
needed in advance.

WALL FRAMING FOR ADEQUATE SUPPORT

• These vent hoods are heavy. Adequate structural support

must be provided. Hoods must be secured to vertical
studs in the wall.

• It is strongly recommended that the vent hood with duct

cover be on site before final framing and wall finishing.
This will also help to accurately locate the ductwork and
electrical service.

DECORATIVE DUCT COVERS

Decorative duct covers, 6" and 12" high, are available to t

all models. The duct cover conceals the ductwork running
from the top of the hood to the ceiling or sot. Stack one
or more duct covers over the top of the hood to reach
your ceiling height.

ZV48SSJSSMONOGRAM 48" STAINLESS STEEL PROFESSIONAL HOOD

POWER SUPPLY

IMPORTANT – (PLEASE READ CAREFULLY)

WARNING

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.

Do not use an extension cord or adapter plug with this

appliance. Follow national electrical codes or prevailing
local codes and ordinances.

ELECTRIC SUPPLY

These vent hoods must be supplied with 120V, 60Hz, and

connected to an individual, properly grounded branch

circuit, and protected by a 15 or 20 amp circuit breaker or

time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

• Route house wiring as close to the installation location as

possible on the back wall or ceiling.

• Connect the wiring to the house wiring in accordance with

local codes.

GROUNDING INSTRUCTIONS

The grounding conductor must be connected to a ground
metal, permanent wiring system, or an equipment-grounded
terminal or lead on the hood.

WARNING

The improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with
a qualified electrician or service representative if you are in
doubt whether the appliance is properly grounded.

OPTIONAL DUCT COVER ACCESSORIES

Decorative duct covers are available in 6" and 12" heights.

Duct covers may be stacked, in various combinations, to
conceal the ductwork running from the top of the hood
to the ceiling.

• Before you begin, you should determine the installation

height of the hood and order

the correct size duct cover. The

duct covers should be ordered
at the same time as the vent
hood and be on site before
installation. Order the duct cover
corresponding to your model.

6" DUCT COVERS

HOOD MODEL 6" DUCT COVER DIMENSIONS

ZV48SSJSS ZX48DC6J 6"H x 19-11/16"W x

11-7/8"D

12" DUCT COVERS

HOOD MODEL 12" DUCT COVER DIMENSIONS

ZV48SSJSS ZX48DC12J 12"H x 19-11/16"W x

11-7/8"D

Listed by
Underwriters
Laboratories

Product Specification Revised 1/18

ZV48SSJSSMONOGRAM 48" STAINLESS STEEL PROFESSIONAL HOOD

A

C

B

Ceiling Height

A - B = C

18" Hood

Height

8 ft. Ceiling 9 ft. Ceiling

INSTALLATION EXAMPLES

10 ft. Ceiling

12"

24"

30"

30"

36"

30"

10 ft. Ceiling

36"

30"

INSTALLATION EXAMPLES

10 ft. Ceiling

24"

30"

36"

30"

USING DUCT COVER ACCESSORIES

To avoid unsightly gaps, plan the hood installation
height for duct covers use. Use the following formula to
calculate the need for one of more duct covers and to
ensure a trouble free installation.

We recommend that the vent hood and decorative
duct cover (if used) be on site before final framing and
wall finishing. This will help to accurately locate studs,
ductwork and electrical service.

• Read these examples carefully to determine the need
for one or more 6" or 12" duct covers.

A = Countertop to ceiling height.

B = Gap at the top of the hood to the ceiling.

C = Hood installation height – Plus 10" hood height.

NOTE

Dia. C should be between 48" and 54" (for a 30" to 36"

installation height). Raise or lower the hood installation

height to allow use of one or more 6" or 12" duct covers.

CEILING HEIGHT

INSTALLATION EXAMPLES

8 FT. CEILINGS

When the hood is

installed 30" above

the cooking surface
and there is no
sot or upper
cabinetry, order

one 12" duct cover

accessory.

9 FT. CEILINGS

When the hood is

installed 30" above

the cooking surface,

order two 12" duct

cover accessories.

10 FT. CEILINGS

When the hood is

installed 36" above

the cooking surface,

order three 12" and
one 6" duct cover

accessories.

Listed by
Underwriters
Laboratories

Product Specification Revised 1/18

FEATURES AND BENEFITS

940 CFM VERTICAL EXHAUST
WITH DUAL BLOWERS

3 HALOGEN LAMPS WITH 4 LIGHTING LEVELS

INFRARED WARMING LAMP

UTENSIL RACKS

REMOVABLE GREASE TRAYS

DISHWASHER-SAFE REMOVABLE BAFFLE

STAINLESS STEEL FILTERS

VARIABLE SPEED FAN CONTROL

ZV48SSJSSMONOGRAM 48" STAINLESS STEEL PROFESSIONAL HOOD

Product Specification Revised 1/18