MONOGRAM 30" STAINLESS STEEL
ADA
WARMING DRAWER
ZTW900PSNSS
COMPLIANT
THE MONOGRAM STATEMENT COLLECTION
Edge-to-edge handles, polished sta inless steel, and
hand-finished edges convey a sense of solidity and bea uty
1.9 CU. FT. CAPACITY
"ON" INDICATOR LIGHT
INFINITE SETTING TEMPERATURE CONTROL
VARIABLE HUMIDITY CONTROL
Crisp to moist
REMOVABLE HALF RACK
STAINLESS STEEL DRAWER FRONT
WITH MINIMAL HANDLE
Accepts 3/4" trimless custom panel and custom
handle with trim kit
FULL EXTENSION DRAWER ON BALL
BEARING GLIDES
ON/OFF ROCKER SWITCH
For questions about your
appliance, please call 1-800-626-2000.
PAGE 1 OF 6
Product Specication Created 10/19
OVERALL DIMENSIONS
SPECIFICATIONS
Overall Width 29 3/4" (75.5 cm)
Overall Height 10 1/2" (26.7 cm)
Overall Depth 23 1/4" (59.0 cm)
Drawer Capacity 1.90 cu. ft. (53.8 l)
Cut-out Width 28 1/2" (72.4 cm)
Cut-out Height 9 1/4" (23.5 cm)
Cut-out Depth 23 1/2" (59.7 cm)
Power Cord Length 56" (142.2 cm)
Electrical Rating 450W @ 120V/60Hz
Total Amps 15 Amps
Net Weight 59 lbs. (26.8 kg)
Approx. Shipping Weight 65 lbs. (29.6 kg)
29 3/4" (75.5)
9 1/4"
(23.5)
cutout height
5/8"
(1.6)
FRONT VIEW (SHOWING CUTOUT OVERLAP)
2 9/16"
(6.5)
28 1/2" (72.4)
cutout width
27 15/16" (71.0)
TOP VIEW
1 13/16"
(4.6)
10 1/2"
23 1/4"
(59.0)
1 7/16"
(3.6)
(26.7)
OPTIONAL ACCESSORIES
Custom Panel Kit ZXD30B
ATTENTION ELECTRICIAN:
is appliance is supplied with a 56" (142.2 cm) long electrical
cord equipped with a 3-prong (grounding) plug tha t mates to a
standa rd 3-prong grounding wall outlet.
e electrical power cord is located on the right side of the
warming drawer. Loca te the wall outlet within easy reach of the
electrical cord in an adjacent ca binet, within 42" (106.7 cm) of
the right side or 16" (40.6 cm) from the left side of the cut-out. A
recessed outlet can be installed on the right side of the cut-out, 7"
(17.8 cm) max. from the rear of the ca binet.
DO NOT USE AN EXTENSION CORD
WITH THIS PRODUCT.
For more details refer to the installa tion instructions for this product.
For questions about your
appliance, please call 1-800-626-2000.
27 3/16" (69.0)
including handle
9"
(22.9)
23 1/4" (59.0)22 11/16" (57.6)
SIDE VIEW
Dimensions in parentheses a re in centimeters unless otherwise noted.
Actual product dimensions may vary due to ma nufacturing tolerances.
Product Specication Created 10/19PAGE 2 OF 6
SIDE VIEW FRONT VIEW
28 1/2" (72.4)
min. cutout width
2" (5.1)
min.
23 1/2" (59.7)
min. cutout depth
1" (2.5) min.
above toe-kick
or adjust to
oven height
9 1/4"
(23.5)
cutout height
TOP VIEW
Side cleats
ZTW900PSNSS
SIDE VIEW FRONT VIEW
28 1/2" (72.4)
min. cutout width
2" (5.1)
min.
23 1/2"
(59.7)
min. cutout depth
1" (2.5) min.
above toe-kick
or adjust to
oven height
9 1/4"
(23.5)
cutout height
TOP VIEW
Side cleats
ZTW900PSNSS
INSTALLATION BELOW SINGLE OR DOUBLE WALL OVEN
A
B
D
INSTALLATION BELOW COOKTOP
HELPFUL TIPS
A
Warming drawers are approved for
installation below only certa in specified
wall oven and cooktop models. See the
label a ttached to the top of the warming
drawer for approved combinations.
C
B
Additional clearance between cut-outs
may be required. Check to be sure that
oven supports above the wa rming drawer
location do not obstruct the required
interior 23-1/2" depth and 9-1/4" height.
C
If you are installing in frameless cabinets, it
may be necessary to install 1/2" wide clea ts
to accept drawer mounting screws. See
drawer for mounting screw locations.
D
Install a 2"x2" or 2"x4" Anti-tip block
against rea r wall, 9" from floor of cutout to
bottom of block. e anti-tip block must be
installed to prevent the drawer from tipping
forward when opened a nd loaded. Failure
to add the anti-tip block could result in
C
personal injury.
E
When installing the warming drawer below
a cooktop, a solid barrier must be installed
at least 1" from the lowest point of the
bottom of cooktop burner box to the top of
the cut-out. Use any solid ma terial such as
1/4" thick plywood. Allow at least 1/4" a ir
gap between the barrier a nd the top of the
warming drawer.
For more details refer to the installa tion
instructions for this product.
From top of countertop
5 1/2"
to top of warming
(14.0)
drawer cutout
min.
D
9 1/4"
(23.5)
cutout height
1" (2.5) min.
above toe-kick
or adjust to
cooktop height
23 1/2" (59.7)
min. cutout depth
E
SIDE VIEW FRONT VIEW
For questions about your
appliance, please call 1-800-626-2000.
28 1/2" (72.4)
min. cutout width
PAGE 3 OF 6
C
Product Specication Created 10/19
ZTW900PSNSS
INSTALLATION BELOW A CABINET DRAWER
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout depth
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
Side cleats
9 1/4"
(23.5)
Cut-out
height
ZTW900PSNSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout depth
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
Side cleats
9 1/4"
(23.5)
Cut-out
height
ZTW900PSNSS
1/4"
(.6)
min.
B
9 1/4"
(23.5)
Cut-out
height
1"
(2.5)
min.
Above
toe-kick
SIDE BY SIDE INSTALLATION
23 1/2" (59.7)
min. cutout depth
SIDE VIEW
Between cut-outs
C
D
2" (5.1) min.
TOP VIEW
28 1/2" (72.4)
min. cutout width
FRONT VIEW
Side cleats
A
HELPFUL TIPS
If you are installing in frameless ca binets, it
A
may be necessary to install 1/2" wide clea ts to
accept drawer mounting screws. See drawer
for mounting screw locations.
Install a 2"x2" or 2"x4" anti-tip block aga inst
B
rear wall, 9" from floor of cutout to bottom
of block. e anti-tip block must be installed
to prevent the drawer from tipping forward
when opened and loaded. Fa ilure to add the
anti-tip block could result in personal injury.
When installing the warming drawer below
C
a ca binet drawer, a solid barrier must be
installed at least a bove the warming drawer
to block access. Use any solid ma terial such
A
as 1/4" thick plywood. Allow at least 1/4"
air gap between the ba rrier and the top of
the warming drawer. Observe the 5" min.
above the floor or 1" min. a bove the toe kick
installation height.
When installing two warming drawers side
D
by side, install them in separa te cut-outs and
allow a 2" min. gap between each cut-out.
E
e warming drawer may be supported
by either a solid bottom or 2"x2" or 2"x4"
runners. e support must be level and
rigidly mounted, flush with the bottom edge
of the cut-out (there is no way to level the
drawer once it has been installed, so make
sure that the supports a re level). e floor
or runners must be capable of supporting
at least 150 lbs.
For more details refer to the installa tion
instructions for this product.
PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or Equivalent Runners
E
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
25" (63.5)
30" (76.2)
For questions about your
appliance, please call 1-800-626-2000.
PAGE 4 OF 6
B
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Product Specication Created 10/19
INSTALLATION WITH CUSTOM PANEL KIT - ZXD30B
30" (76.2)
10 1/2"
(26.7)
1 13/16" (4.6)
3/4" (1.9) max.
HELPFUL TIPS
• is kit contains a mounting panel to support
a trim-less custom drawer front up to 3/4"
thick. e original tubular ha ndle can be
reinstalled onto the custom panel with longer
screws (not provided) or can be replaced
with a custom ha ndle of your choice (also not
provided).
For more details refer to the installa tion
instructions for this product.
Drill
5/16" (0.8)
through custom
panel for lamp jewel
CUSTOM PANEL PREPARATION
FRONT VIEW
Drawer
open
Excluding
custom panel
1 3/4" (4.5)
SIDE VIEW
23 5/16" (59.2)
including handle
Excluding
custom panel
23 1/4" (59.0)24" (61.0)
CUSTOM PANEL
PREPARATION
SIDE VIEW
9"
(22.9)
For questions about your
appliance, please call 1-800-626-2000.
PAGE 5 OF 6
Product Specication Created 10/19
INSTALLATION
ZTW900PSNSS
30" (76.2)
9 1/4"
(23.5)
Cutou-out height
5/8"
(1.6)
1"
(2.5)
26" (66.0)
Handle width
28 1/2" (72.4)
Cut-out width
FRONT VIEW (SHOWING CUT-OUT OVERLAP)
27 15/16" (71.0)
2 1/4"
(5.7)
10 1/2"
23 1/4"
(59.0)
(26.7)
2 13/16"
(7.1)
27 19/32" (70.1) 23 1/4" (59.0)
For questions about your
appliance, please call 1-800-626-2000.
TOP VIEW
27 13/32" (69.6)
Including Handle
SIDE VIEW
1 11/32"
(3.4)
9"
(22.9)
PAGE 6 OF 6
Product Specication Created 10/19
Loading...