GE Monogram® 27" Warming Drawer
OVERALL DIMENSIONS
26 3/4" (68.0)
22 9/32" (56.6)
handle width
ZJ7000SJSS
1 3/32"
(2.8)
SPECIFICATIONS
Overall Width 26 3/4" (68.0 cm)
Overall Height 10 1/2" (26.7 cm)
Overall Depth 23 1/4" (59.0 cm)
Drawer Capacity 1.67 cu. ft. (47.3 l)
Cut-out Width 25 1/2" (64.8 cm)
Cut-out Height 9 1/4" (23.5 cm)
Cut-out Depth 23 1/2" (59.7 cm)
Power Cord Length 56" (142.2 cm)
Electrical Rating 450W @ 120V/60Hz
Total Amps 15 Amps
Net Weight 53 lbs. (23.6 kg)
Approx. Shipping Weight 59 lbs. (26.8 kg)
OPTIONAL ACCESSORIES
Custom Panel Kit ZXD27B
9 1/4"
(23.5)
cutout height
5/8"
(1.6)
25 1/2" (64.8)
cutout width
FRONT VIEW (SHOWING CUTOUT OVERLAP)
24 27/32" (63.1)
23 1/4"
(59.0)
10 1/2"
(26.7)
ATTENTION ELECTRICIAN:
This appliance is supplied with a 56" (142.2 cm)
long electrical cord equipped with a 3-prong
(grounding) plug that mates to a standard
3-prong grounding wall outlet.
The electrical power cord is located on the right
side of the warming drawer. Locate the wall
outlet within easy reach of the electrical cord in
an adjacent cabinet, within 42" (106.7 cm) of the
right side or 16" (40.6 cm) from the left side of the
cut-out. A recessed outlet can be installed on the
right side of the cut-out, 7" (17.8 cm) max. from
the rear of the cabinet.
DO NOT USE AN EXTENSION CORD
WITH THIS PRODUCT.
For more details refer to the installation instructions
for this product.
2"
(5.1)
Dimensions in parentheses
are in centimeters unless
otherwise noted. Actual
product dimensions may
vary due to manufacturing
tolerances.
TOP VIEW
26 1/2" (67.3)
including handle
SIDE VIEW
1 9/32"
(3.2)
9"
(22.9)
23 1/4" (59.0)22" (55.9)
Product Specification Created 9/14
GE Monogram® 27" Warming Drawer
SIDE VIEW FRONT VIEW
25 1/2" (64.8)
min. cutout width
2" (5.1)
min.
23 1/2"
(59.7)
min. cutout depth
1" (2.5) min.
above toe-kick
or adjust to
oven height
9 1/4"
(23.5)
cutout height
TOP VIEW
Side cleats
ZJ7000SJSS
INSTALLATION BELOW SINGLE OR DOUBLE WALL OVEN
A
2" (5.1)
min.
9 1/4"
(23.5)
cutout height
B
D
TOP VIEW
Side cleats
C
25 1/2" (64.8)
min. cutout width
NOTES
A
Warming drawers
are approved for
installation below
only certain specified
wall oven and cooktop
models. See the label
attached to the top of
the warming drawer for
approved combinations.
B
Additional clearance
between cut-outs may
be required. Check to be
sure that oven supports
above the warming
drawer location do not
obstruct the required
interior 23-1/2" depth
and 9-1/4" height.
C
If you are installing in
frameless cabinets,
it may be necessary
to install 1/2" wide
C
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.
1" (2.5) min.
above toe-kick
or adjust to
oven height
INSTALLATION BELOW COOKTOP
From top of countertop
5 1/2"
to top of warming
(14.0)
drawer cutout
min.
9 1/4"
(23.5)
cutout height
1" (2.5) min.
above toe-kick
or adjust to
cooktop height
23 1/2" (59.7)
min. cutout depth
SIDE VIEW FRONT VIEW
D
25 1/2" (64.8)
min. cutout width
23 1/2" (59.7)
min. cutout depth
E
SIDE VIEW FRONT VIEW
D
Install a 2"x2" or 2"x4"
Anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.
E
When installing the
warming drawer
below a cooktop, a
solid barrier must be
installed at least 1"
from the lowest point of
the bottom of cooktop
burner box to the top
of the cut-out. Use any
C
solid material such as
1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
For more details refer
to the installation
instructions for this
product.
Product Specification Created 9/14
GE Monogram® 27" Warming Drawer
SIDE VIEW
FRONT VIEW
TOP VIEW
25 1/2" (64.8)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
Side cleats
9 1/4"
(23.5)
Cut-out
height
SIDE VIEW
FRONT VIEW
TOP VIEW
25 1/2" (64.8)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
Side cleats
9 1/4"
(23.5)
Cut-out
height
ZJ7000SJSS
INSTALLATION BELOW A CABINET DRAWER
TOP VIEW
Side cleats
A
1/4"
(.6)
min.
B
9 1/4"
(23.5)
Cut-out
height
1"
(2.5)
min.
SIDE BY SIDE INSTALLATION
PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS
23 1/2"
(59.7)
Above
toe-kick
2" (5.1) x 4" (10.2)
or Equivalent Runners
23 1/2" (59.7)
min. cutout width
SIDE VIEW
E
C
D
2" (5.1) min.
Between cut-outs
22" (55.9)
27" (68.6)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
25 1/2" (64.8)
min. cutout width
FRONT VIEW
A
B
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
NOTES
A
If you are installing in
frameless cabinets,
it may be necessary
to install 1/2" wide
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.
B
Install a 2"x2" or 2"x4"
anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.
C
When installing the
warming drawer below
a cabinet drawer, a
solid barrier must be
installed at least above
the warming drawer
to block access. Use
any solid material such
as 1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
Observe the 5" min.
above the floor or 1"
min. above the toe kick
installation height.
D
When installing two
warming drawers side
by side, install them
in separate cut-outs
and allow a 2" min. gap
between each cut-out.
E
The warming drawer
may be supported by
either a solid bottom or
2"x2" or 2"x4" runners.
The suppor t must
be level and rigidly
mounted, flush with
the bottom edge of the
cut-out (there is no way
to level the drawer once
it has been installed,
so make sure that the
supports are level). The
floor or runners must be
capable of supporting
at least 150 lbs.
For more details refer
to the installation
instructions for this
product.
Product Specification Created 9/14
GE Monogram® 27" Warming Drawer
ZJ7000SJSS
INSTALLATION WITH CUSTOM PANEL KIT - ZXD27B
26 3/4" (76.2)
10 1/2"
(26.7)
Drill
5/16" (0.8)
through custom
panel for lamp jewel
CUSTOM PANEL PREPARATION
FRONT VIEW
1 3/4" (4.5)
23 5/16" (59.2)
including handle
Excluding
custom panel
1 13/16" (4.6)
3/4" (1.9) max.
CUSTOM PANEL
PREPARATION
SIDE VIEW
NOTES
This kit contains a
mounting panel to support
a trim-less custom drawer
front up to 3/4" thick. The
original tubular handle
can be reinstalled onto the
custom panel with longer
screws (not provided) or
can be replaced with a
custom handle of your
choice (also not provided).
For more details refer
to the installation
instructions for this
product.
Drawer
open
Excluding
custom panel
SIDE VIEW
9"
(22.9)
23 1/4" (59.0)24" (61.0)
Product Specification Created 9/14
GE Monogram® 27" Warming Drawer
FEATURES AND BENEFITS
1.67 cu. ft. capacity
On indicator light
Infinite Setting Temperature Control –
75 Degrees to 230 Degrees
Variable Humidity Control – Crisp to Moist
ZJ7000SJSS
Removable Half Rack
"On" indicator light
Accepts 1/4" to 1/2" trimless custom panels
and custom handle with trim kit
Stainless steel drawer front with tubular handle
Full extension drawer on ball bearing glides
Variable Installation Options
Hidden Controls Provide Flush Installation
Appearance
On/Off Rocker Switch
R
Product Specification Created 9/14
Loading...