Monogram ZISS480NKSS Specsheet
*84"
(213.4)
48" (121.9)
25 3/4" (65.4)
23 7/8" (60.7)
2"
(5.1)
*71 7/8"
(182.6)
*3 3/8"
(8.6)
*83 1/2"
(212.1)
64 3/8"
(163.5)
*6 1/4"
(15.9)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
OVERALL DIMENSIONS
48" (121.9)
ZISS480NKSSMONOGRAM 48" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
2"
(5.1)
25 3/4" (65.4)
23 7/8" (60.7)
SPECIFICATIONS
Overall Width 48" (121.92 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/4" (65.41 cm)
Door Clearance 28 5/8" (72.7 cm)
Cutout Width 47 1/2" (120.7 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 775 lb
*84"
(213.4)
*71 7/8"
(182.6)
64 3/8"
(163.5)
*6 1/4"
(15.9)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
47" (119.4)
Case width
** Allow 15" (38.1) min
clearance for 130˚
door swing
*3 3/8"
(8.6)
** Allow 20" (50.8) min
clearance for 130˚
door swing
SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
recessed into the back wall.
28 5/8"
(72.7)
TOP VIEW
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances.
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
Product Specification Revised 1/18
ZISS480NKSSMONOGRAM 48" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4"
(10.2)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
STANDARD INSTALLATION
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
5"
(12.7)
The refrigerator will project forward, slightly beyond adjacent cabinetry.
ANTI-TIP BRACKET
C
SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
24" (61.0)
2"
(5.1)
47 1/2" (120.7)
A
6"
(15.2)
E
5"
(12.7)
B
20" (50.8)
5"
(12.7)
From floor
to bottom
of electrical
3 1/2"
(8.9)
75"
(190.5 )
area
4"
(10.2)
WATER
FRONT VIEW SIDE VIEW
D
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*Or installation
height from floor
Screws mounted
into vertical wall
*84"
(213.4)
2" x 4"
Cut to 35" Length
studs
Top Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
W
7/16"
Trim overlap
3 1/2"
(8.9)
3/4"
Min.
Side View Top
Case Trim
(1.1)
NOTES
A
Mounting the junction box
in this location will also
allow for front accessibility
through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy
and must be secured to
prevent the possibility of
tipping forward. Failure to
do so may result in death or
serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system
you must use the product
installation instructions.
Determine your installation
construction and required antitip configuration:
C
Installed Under Sot
After installing unit into
installation opening, raise
grille panel and screw metal
case sides to adjacent cabinet.
When installed under a sot,
the sot cannot exceed 24"
deep. The top case trim
overlaps the bottom of the
sot.
D
Wooden Wall Studs and No
Sot
• Cut a 2" x 4" block and
secure to brackets provided.
• Secure brackets to back wall
of opening at 84" or your
installation height from the
floor.
E
Metal Wall Studs and No
E
Sot
This method requires securely
fastened cabinets on both
sides and a 3/4" minimum
wood brace above unit, with
it’s front surface 24" from back
wall.
• After installing unit into
opening, raise grille panel and
attach metal case top trim to
3/4" minimum wood brace.
• The brace spanning the
enclosure must be securely
fastened to cabinets on both
sides.
See Installation Instructions for
detailed instructions.
Product Specification Revised 1/18
Loading...