Monogram ZISP480DHSS Specification Sheet
OVERALL DIMENSIONS
*84"
(213.4)
48" (121.9)
25 3/4" (65.4)
23 7/8" (60.7)
13 1/2"
(34.3)
30 1/2"
(77.5)
*39 1/2"
(100.3)
*30 1/4"
(76.8)
2 3/4"
(7.0)
*72 1/4"
(183.5)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
48" (121.9)
ZISP480DHSSGE Monogram® 48" Built-In Side-by-Side Refrigerator
2 3/4"
(7.0)
25 3/4" (65.4)
23 7/8" (60.7)
SPECIFICATIONS
Overall Width 48" (121.92 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/4" (65.41 cm)
Door Clearance 28 5/8" (72.7 cm)
Cutout Width 47 1/2" (120.7 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1.4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 800 lb
*84"
(213.4)
13 1/2"
(34.3)
*39 1/2"
(100.3)
30 1/2"
(77.5)
*30 1/4"
(76.8)
*72 1/4"
(183.5)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
47" (119.4)
Case width
** Allow 15" (38.1) min
clearance for 130˚
door swing
*3 1/2"
(8.9)
** Allow 20" (50.8) min
clearance for 130˚
door swing
SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
28 5/8"
TOP VIEW
** Allow 5" (12.7) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimension may vary due to manufacturing tolerances.
** Allow 5" (12.7) min
clearance to a wall for 90˚
door swing
Product Specification Created 6/14
(72.7)
GE Monogram® 48" Built-In Side-by-Side Refrigerator
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5)
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISP480DHSS
STANDARD INSTALLATION
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
ANTI-TIP BRACKET
SIDE VIEW INSTALLED
UNDER SOFFIT
(12.7)
C
SOFFIT
6"
(15.2)
5"
FRONT VIEW SIDE VIEW
47 1/2" (120.7)
A
20" (50.8)
E
5"
(12.7)
From floor
to bottom
of electrical
3 1/2"
5"
(12.7)
(8.9)
WATER
B
D
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
75"
(190.5)
area
Screws mounted
into vertical wall
*84"
(213.4)
*Or installation
height from floor
4 3/4"
(12.1)
24" (61.0)
2"
(5.1)
W
The refrigerator will project forward,
slightly beyond adjacent cabinetry.
2" x 4"
Cut to 35" Length
studs
Top Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
Side View Top
Case Trim
3/4"
Min.
NOTES
A
Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
Determine your installation
construction and required
anti-tip configuration:
C
Installed Under Soffit
After installing unit into
installation opening,
raise grille panel and
screw metal case sides to
adjacent cabinet. When
installed under a soffit,
the soffit cannot exeed 24”
deep. The top case trim
overlaps the bottom of the
soffit.
D
Wooden Wall Studs and
No Soffit
• Cut a 2” x 4” block and
secure to brackets
provided.
• Secure brackets to back
wall of opening at 84” or
your installation height
from the floor.
E
Metal Wall Studs and
No Soffit
E
This method requires
securely fastened cabinets
on both sides and a ¾”
minimum wood brace
above unit, with it’s front
surface 24” from back wall.
• After installing unit into
opening, raise grille panel
and attach metal case
top trim to ¾” minimum
wood brace.
• The brace spanning
the enclosure must be
securely fastened to
cabinets on both sides.
See Installation
Instructions for detailed
instructions.
Product Specification Created 6/14
Loading...