42" (106.7)
*84"
(213.4)
*72 1/4"
(183.5)
2 3/4"
(7.0)
*3 1/4"
(8.3)
SIDE VIEWFRONT VIEW
25 3/4" (65.4)
23 7/8" (60.7)
*83 1/2"
(212.1)
13 1/2"
(34.3)
30 1/2"
(77.5)
*39 1/2"
(100.3)
*30 1/4"
(76.8)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
OVERALL DIMENSIONS
42" (106.7)
13 1/2"
(34.3)
ZISP420DKSSMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
2 3/4"
(7.0)
25 3/4" (65.4)
23 7/8" (60.7)
SPECIFICATIONS
Overall Width 42" (91.44 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/4" (65.41 cm)
Door Clearance 26 5/8" (67.6 cm)
Cutout Width 41 1/2" (105.4 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 750 lb
*84"
(213.4)
*39 1/2"
(100.3)
30 1/2"
(77.5)
*30 1/4"
(76.8)
*72 1/4"
(183.5)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
41" (104.2)
Case width
** Allow 13" (33.0) min
clearance for 130˚
door swing
*3 1/4"
(8.3)
** Allow
19" (48.3) min
clearance for 130˚
door swing
*83 1/2"
(212.1)
SIDE VIEWFRONT VIEW
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power
supply is required. An inidividual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
recessed into the back wall.
26 5/8"
(67.6)
TOP VIEW
** Allow
clearance to a wall for 90˚
5" (12.7) min
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual
product dimension may vary due to manufacturing tolerances.
** Allow 5" (12.7) min
clearance to a wall for 90˚
door swing
Product Specification Revised 9/16
ZISP420DKSSMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
41 1/2" (105.4)
18" (45.7)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5)
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
STANDARD INSTALLATION
41 1/2" (105.4)
6"
(15.2)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
The refrigerator will project forward, slightly beyond adjacent cabinetry.
ANTI-TIP BRACKET
SIDE VIEW INSTALLED
5"
(12.7)
WATER
FRONT VIEW SIDE VIEW
C
SOFFIT
UNDER SOFFIT
18" (45.7)
A
E
5"
(12.7)
75"
(190.5)
From floor
to bottom
of electrical
area
3 1/2"
5"
B
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
(8.9)
(12.7)
D
AND NO SOFFIT
4 3/4"
(12.1)
Screws mounted
into vertical wall
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
studs
WITH METAL WALL STUDS
24" (61.0)
2"
(5.1)
7/16"
Trim overlap
3 1/2"
(8.9)
W
Side View Top
Top Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
Case Trim
FRONT VIEW INSTALLED
AND NO SOFFIT
(1.1)
3/4"
Min.
NOTES
A
Mounting the junction box
in this location will also
allow for front accessability
through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy
and must be secured to
prevent the possibility of
tipping forward. Failure to
do so may result in death or
serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system
you must use the product
installation instructions.
Determine your installation
construction and required
anti-tip configuration:
C
Installed Under Sot
After installing unit into
installation opening, raise
grille panel and screw metal
case sides to adjacent cabinet.
When installed under a sot,
the sot cannot exeed 24"
deep. The top case trim
overlaps the bottom of the
sot.
D
Wooden Wall Studs and No
Sot
• Cut a 2" x 4" block and
secure to brackets provided.
• Secure brackets to back wall
of opening at 84" or your
installation height from the
floor.
E
Metal Wall Studs and No
E
Sot
This method requires securely
fastened cabinets on both
sides and a 3/4" minimum
wood brace above unit, with
it’s front surface 24" from back
wall.
• After installing unit into
opening, raise grille panel and
attach metal case top trim to
3/4" minimum wood brace.
• The brace spanning the
enclosure must be securely
fastened to cabinets on both
sides.
See Installation Instructions for
detailed instructions.
Product Specification Revised 9/16
ZISP420DKSSMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*Depending
*Depending
on installation
on installation
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
*84”
*84"
(213.4)
(213.4)
height
NOTES
F
Side panels must be used
whenever the sides of
the refrigerator will be
exposed. The 1/4" side
panels will slip into the
side case trim. Secure the
panels to the refrigerator
with stick-on hook and
loop fastener strips. Order
the side panels from the
cabinet manufacturer.
2 9/16"
(6.5)
Product Specification Revised 9/16
FEATURES AND BENEFITS
ADVANCED TEMPERATURE MANAGEMENT SYSTEM WITH
MULTI-SHELF BRUSHED ALUMINUM AIR TOWER
Provides even distribution of air throughout the refrigerator
CLIMATE-CONTROL DRAWER
Allows you to express-chill beverages, express-thaw meats
and select specific temperatures for perishable foods
WIFI CONNECT
Enjoy the convenience and freedom of wirelessly controlling
functions from your smartphone
LED LIGHTING
Light columns in the freezer and fresh food compartments
extend the full length of the interior and LED lighting located
inside the vegetable and climate-control drawers illuminate
contents without compromising space
COLOR-MATCHED DISPENSER WITH PROXIMITY SENSOR
Designed to accommodate glassware of all sizes, from
pitchers to tumblers; control graphics light up as you
approach and automatically switch o when you walk away
ZISP420DKSSMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
GE® WATER FILTER
Has been moved from the fresh food compartment to the
overhead cabinet, where it is discreetly out of sight
ADJUSTABLE DELI DRAWER ON FULL-EXTENSION SLIDES
Keeps meats, cheeses and other everyday foods within easy
reach
HUMIDITY-CONTROLLED VEGETABLE DRAWER
Helps preserve the freshness of foods
ADJUSTABLE SPILLPROOF GLASS SHELVES
Easily accommodate party trays and platters
GALLON-SIZE DOOR BIN
Holds milk containers, two-liter bottles and pitchers
ADJUSTABLE DOOR BINS
Can be moved to one of two positions in seven locations
DAIRY BIN WITH CENTER DIVIDER
Has a unique magnetic seal that locks in freshness
FILTER-CHANGE INDICATOR LIGHT
Located on the upfront control panel, provides a visual
reminder when it's time to replace the filter for the water
dispenser
R
Product Specification Revised 9/16
Loading...