Monogram ZISB420DK Product Specifications - Download
SECTION 1
STANDARD INSTALLATION
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
ZISB420DKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
SECTION 2
FLUSH INSET INSTALLATION
Product Specification Revised 9/16
*84"
(213.4)
42" (106.7)
25 1/2" (64.8)
23 7/8" (60.7)
1 3/4"
(4.4)
*72 1/4"
(183.5)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
13 1/2"
(34.3)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
(9.5)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
13 1/2"
*84"
(213.4)
(34.3)
42" (106.7)
ZISB420DKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
STANDARD INSTALLATION
25 1/2" (64.8)
23 7/8" (60.7)
1 3/4"
(4.4)
*83 1/2"
(212.1)
SPECIFICATIONS
Overall Width 42" (106.7 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/8" (64.453 cm)
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 41 1/2" (105.4 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 725 lb (328.9 kg)
(9.5)
*72 1/4"
(183.5)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
41" (104.2)
Case width
** Allow 13" (33.0) min
clearance for 130˚
door swing
*3 1/2"
(8.9)
** Allow 19" (48.3) min
clearance for 130˚
door swing
SIDE VIEWFRONT VIEW
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker is
recommended. Install a properly grounded
3-prong electrical receptacle recessed into
the back wall.
26 5/8"
(67.6)
TOP VIEW
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
Product Specification Revised 9/16
ZISB420DKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
AND NO SOFFIT
AND NO SOFFIT
STANDARD INSTALLATION
3 1/8"
(7.93)
24" (61)
1 9/16"
(3.97)
SIDE VIEW
The refrigerator will project forward, slightly beyond adjacent cabinetry.
ANTI-TIP BRACKET
C
SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
7/16"
(1.1)
Trim overlap
(214.6)
D
*Or installation
height from floor
3 1/2"
(8.9)
*Trim will overlap
additional 7/16"
*84 1/2"
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
TOP VIEW
41 1/2" (105.4)
6"
(15.24)
5"
(12.7)
FRONT VIEW
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
*84"
(213.4)
18" (45.7)
A
E
5"
(12.7)
B
5"
(12.7)
3 1/2"
(8.9)
WATERW
Top Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
75"
(190.5 )
From floor
to bottom
of electrical
area
3/4"
Min.
Side View Top
Case Trim
STANDARD
INSTALLATION
NOTES
A
Mounting the junction box in
this location will also allow
for front accessibility through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy
and must be secured to prevent
the possibility of tipping forward.
Failure to do so may result in
death or serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system you
must use the product installation
instructions.
Determine your installation
construction and required
anti-tip configuration:
C
Installed Under Sot
After installing unit into
installation opening, raise grille
panel and screw metal case
sides to adjacent cabinet. When
installed under a sot, the sot
cannot exceed 24" deep. The top
case trim overlaps the bottom of
the sot.
D
Wooden Wall Studs and No
Sot
• Cut a 2" x 4" block and secure
to brackets provided.
• Secure brackets to back wall
E
of opening at 84" or your
installation height from the
floor.
E
Metal Wall Studs and No Sot
This method requires securely
fastened cabinets on both sides
and a 3/4" minimum wood brace
above unit, with it’s front surface
24" from back wall.
• After installing unit into
opening, raise grille panel and
attach metal case top trim to
3/4" minimum wood brace.
• The brace spanning the
enclosure must be securely
fastened to cabinets on both
sides.
See Installation Instructions for
detailed instructions.
Product Specification Revised 9/16
ZISB420DKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*Depending
*Depending
on installation
on installation
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
*84”
*84"
(213.4)
(213.4)
height
STANDARD
INSTALLATION
NOTES
F
Side panels must be used
whenever the sides of the
refrigerator will be exposed. The
1/4" side panels will slip into the
side case trim. Secure the panels
to the refrigerator with stick-on
hook and loop fastener strips.
Order the side panels from the
cabinet manufacturer.
2 9/16"
(6.5)
Product Specification Revised 9/16
ZISB420DKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR
1/4" Framed Panel
A
(24.4)
15 3/8"
1/4" FRAMED PANEL DIMENSIONS
Grille Panel
D E
Dispenser
Cutout
F
G
Freezer
Panel
Fresh
Food
Panel
B
C
3/4" OVERLAY PANEL DIMENSIONS
A
B
C
D E
Dispenser
Cutout
G
Freezer
Panel
Grille Panel
F
Fresh
Food
Panel
PANEL ASSEMBLY CROSS SECTION
Trim
Door
Supplied Handles
PANEL DIMENSIONS
A B C D E
1/4" Framed Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"
Dispenser
Cutout
9 5/8"
(24.4)
15 3/8"
(39.1)
DISPENSER CUTOUT
POSITION
F G
17 13/16" 3 1/8"
PANEL ASSEMBLY CROSS SECTION
Trim
1/4" Backer Panel
.10" Spacer Panel
Door
3/4" Overlay Panel
Supplied Handles
PANEL DIMENSIONS
A B C D E
1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"
.10" Spacer Panel 39" 8 5/8" 67" 13 1/4" 23 1/4"
3/4" Overlay Panel 40 1/8" 9 3/4" 68 5/8" 14 13/16" 24 13/16"
.25" + .10" + .75" = 1.10" Total Panel Thickness
* DISPENSER CUTOUT
Dispenser
Cutout
(39.1)
9 5/8"
* Cut the dispenser opening after the backer, spacer and
overlay panels have been assembled.
POSITION
F G
17 15/16" 3 1/4"
STANDARD
INSTALLATION
NOTES
Trimmed refrigerators are
designed to be customized with
decorative panels. Field-installed
custom door and grille panels
are required.
1/4" Framed Panels:
For 1/4" thick custom panels
ordered from your cabinet
maker; the decorative panels
slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
3/4" Overlay Panels:
For 3/4" thick custom panels
ordered from your cabinet
maker; the decorative panels
slide into the trim.
The overlay panel must be
secured to a 1/4"-thick backer
panel which slides into the trim.
A spacer panel 0.10" thick must
be placed between the overlay
and backer panels.
Center each panel over the
other. Assemble the panels with
glue and screws. Screws must
be countersunk into the backer
panel.
NOTE: Left-to-right oset is not
always equal to top-to-bottom
oset.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles:
The supplied handles can be
adjusted to accommodate
both framed or overlay panels.
Custom handles of your choice,
supplied by your cabinet maker,
can also be installed.
ZKHPSS1: Professional tubular
stainless steel handle designed
to fit 3/4" overlay panels.
ZKHSS2: European tubular
stainless steel handle designed
to fit 3/4" overlay panels.
Kits include one handle. Order 2
kits for side-by-side refrigerators
from your Monogram supplier.
Product Specification Revised 9/16
Loading...