Monogram ZISB420DH Specification Sheet

SECTION 1

FLUSH INSET INSTALLATION

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

SECTION 2

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

Product Specification Revised 5/16

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

SPECIFICATIONS

Overall Width 44" (111.8 cm)

Overall Height 84 1/2" (214.6 cm)

Overall Depth 26" (66.0 cm)

Door Clearance 26 5/8" (67.6cm)

Cutout Width 45" (114.3 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 725 lb (328.9 kg)

† Dimensions include 3/4" custom cabinet panel

†

OVERALL DIMENSIONS
AFTER PANEL INSTALL

FLUSH INSET INSTALLATION

26" (66.0)

44" (111.8)

11 3/16"

(28.4)

15 3/8"

(39.1)

72 5/8"

(184.5)

84 1/2"

(214.6)

68 5/8"

(174.3)

*39 17/32"

(100.4)

†

†

4"

FRONT VIEW

Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84".

41" (104.2)

Case width

**13"

(33.0)

(10.2)

**19"

(48.3)

20 5/8" (52.4)

* 83 1/2"

(212.1)

SIDE VIEW

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.

*115° Door swing

Doors can be adjusted to

90° door swing

26 5/8"

(67.6)

TOP VIEW

** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.

** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing

Product Specification Revised 5/16

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )
From floor
to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

FLUSH INSET INSTALLATION 3/4" PANELS

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

85"

(215.9)

Finished cleats

3 1/2"

(8.9)

W

ANTI-TIP BRACKET

C

SOFFIT

Width of side cleats

5 1/4" (13.3)

3/4" (1.9)

85"

(215.9)

TOP VIEW

Finished cleats

Case Trim

3/4" Panel

7"

(17.8)

45" (114.3) Flush inset width

43 1/2" (110.5)

Width between cleats

6"

(15.2)

(12.7)

WATER

FRONT VIEWSIDE VIEW

D

Case

Door

E

5"

19"

(48.3)

7"

(17.8)

B

2" x 4"

Cut to 35" Length

1/2" (1.3)

75"

(190.5 )
From floor
to bottom

of electrical

area

3 1/2"

(8.9)

FLUSH INSET INSTALLATION

NOTES

A

Mounting the junction box in this

location will also allow for front
accessibility through access panel.

B

Water supply area.

A

WARNING:

The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.

The information below is for cabinet
design only. When installing the anti-

tip system you must use the product
installation instructions.

Determine your installation construction
and required anti-tip configuration:

C

Cut a 1" x 4" block 35" long. Measure

and mark under the soffit,
5 1/4" from the front edge of the
cabinet. Secure the wood block under
the soffit. From the bottom of the
block to the finished floor should
measure 84".

D

Wooden Wall Studs and No Soffit

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of

opening at 84" or your installation
height from the floor.

See Installation Instructions for
detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

*84"

(213.4)

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

Screws mounted
into vertical wall

studs

Product Specification Revised 5/16

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )
From floor
to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

Monogram® 42" Built-In Side-by-Side Refrigerator ZISB420DH

FLUSH INSET INSTALLATION 1/2" PANELS

26 3/16" (66.5)

Flush inset depth

20 13/16" (52.9)

Depth to cleat

85"

(215.9)

Finished cleats

3 1/2"

(8.9)

W

ANTI-TIP BRACKET

C

SOFFIT

Width of side cleats

5 3/8" (13.7)

3/4" (1.9)

85"

(215.9)

TOP VIEW

Finished cleats

Case Trim

1/2" Panel

7"

(17.8)

45" (114.3) Flush inset width

43 1/2" (110.5)

Width between cleats

6"

(15.2)

(12.7)

WATER

FRONT VIEWSIDE VIEW

D

Case

Door

E

5"

B

19"

(48.3)

7"

(17.8)

2" x 4"

Cut to 35" Length

1/2" (1.3)

75"

(190.5 )
From floor
to bottom

of electrical

area

3 1/2"

(8.9)

FLUSH INSET INSTALLATION

NOTES

A

Mounting the junction box in this

location will also allow for front
accessibility through access panel.

B

Water supply area.

A

WARNING:

The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.

The information below is for cabinet
design only. When installing the anti-

tip system you must use the product
installation instructions.

Determine your installation
construction and required anti-tip
configuration:

C

Cut a 1" x 4" block 35" long. Measure

and mark under the soffit,
5 3/8" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom of
the block to the finished floor should
measure 84".

D

Wooden Wall Studs and No Soffit

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of

opening at 84" or your installation
height from the floor.

See Installation Instructions for
detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

*84"

(213.4)

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

Screws mounted
into vertical wall

studs

Product Specification Revised 5/16

(24.4)

15 3/8"

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

HINGE

HANDLE

Front

DETAIL BOTTOM

FLUSH INSET 3/4" PANEL DIMENSIONS

A

PANEL DIMENSIONS

Grille Panel

D E

Dispenser

F

Cutout

G

Freezer

Panel

Fresh

Food

Panel

B

A B C D E

44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

Dispenser

Cutout

C

9 5/8"

3/4" RAISED DOOR PANEL ROUTING

DETAIL TOP

3/4"

11/32"

1/4"

7/16"

1/4"

DISPENSER CUTOUT

(39.1)

NOTE: Routed areas should be
finished as they may be visible
when assembled.

POSITION

F G

17 23/32" 3 3/8"

Front

TOP

FLUSH INSET INSTALLATION

NOTES

Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed 1/2" or 3/4" custom door and
grille panels are required. For 3/4" raised
door and grille panels, routing is required.
The router depth is 1/4" all the way around
the panel’s backs. Additional panel width
reductions are required per the diagrams
shown. This will create “picture frame”
routing allowing the panels to slide into
the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.

Door Handles

Door handle not included. A custom handle
supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" panels. Kit includes

one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit includes

one handle – 64 1/4" long.

3/16"

DETAIL HINGE

SIDE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

Back

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

3/16"

FrontBack

DETAIL HANDLE

SIDE

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Product Specification Revised 5/16

Monogram® 42" Built-In Side-by-Side Refrigerator

“PICTURE FRAME” ROUTING

ZISB420DH

3/4" RAISED GRILLE PANEL ROUTING

NOTE: Routed areas should be
finished as they may be visible
when assembled.

Front

Back

CORNER VIEW SHOWING

DETAIL

LEFT SIDE

2"

3/16"

DETAIL BOTTOM

DETAIL TOP

ROUTER DEPTH 1/4"

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

DETAIL RIGHT

SIDE

TOP

FLUSH INSET INSTALLATION

NOTES

Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door and grille panels are
required. For 3/4" raised door and grille
panels, routing is required. The router
depth is 1/4" all the way around the
panel’s backs. Additional panel width

FrontBack

reductions are required per the diagrams
shown. This will create “picture frame”
routing allowing the panels to slide into
the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.

Door Handles

Door handle not included. A custom
handle supplied by your cabinet maker
may be used.

ZKHPSS1: Professional tubular stainless
steel handle designed to fit 3/4" panels.

Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit

includes one handle – 64 1/4" long.

LEFT
SIDE

ROUTER DEPTH 1/4"

2 1/16" 2 1/16"

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

ROUTER DEPTH 1/4"

RIGHT

SIDE

Product Specification Revised 5/16

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

DISPENSER TRIM

3/4" Flush Panel

A

Freezer Door

Ice/Water Dispenser

1/2" Overlay Panel

3/4" OVERLAY PANEL

DISPENSER TRIM

RAISED PANEL DESIGN ON DISPENSER MODELS

16 3/4"

10 5/8"

DISPENSER TRIM

1/4" Backer Panel

.10" Spacer Panel

Freezer Door

Ice/Water Dispenser

1/2" OVERLAY PANEL

DISPENSER TRIM

3/4" or 1/2" Flush Panel

B

.85"

Total

Thickness

3/4" or .85"

Total

Thickness

C

FLUSH INSET INSTALLATION

NOTES

These refrigerators are supplied with a
dispenser trim for flush inset panels.

Panel Dispenser Trim:

A

The provided dispenser trim is designed
to fit a total panel thickness of 3/4"
or 0.85".

• If the panel is less than 3/4" thick, a

noticeable gap may be created around
the dispenser trim.

• If the panel is more than 0.85" thick, the

dispenser trim cannot be secured to
the door.

• The overlay panel must be constructed

according to the specifications shown
to achieve the correct total thickness.

• When a raised panel design is to be used,
a custom middle rail is required.

Raised Panel Design on Dispenser Models:

When a raised panel design is to be used, a
custom wide middle rail is required to accept
the dispenser trim.

• The middle rail must be wide enough to

B

allow for the dispenser trim to overlap
the opening.

• The middle rail must be 3/4" total

C

thickness for 3/4" panels or 0.85" total
thickness for 1/2" panels to accept the
dispenser trim.

SIDE VIEW CROSS SECTION
(Showing Raised Panel with

Middle Rail)

Product Specification Revised 5/16

Monogram® 42" Built-In Side-by-Side Refrigerator

(24.4)

15 3/8"

ZISB420DH

FLUSH INSET 1/2" PANEL DIMENSIONS

A

PANEL DIMENSIONS

Grille Panel

D E

Dispenser

F

Cutout

G

B

1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

.10" Space Panel 39" 8 5/8" 67" 13 9/16" 23 9/16"

1/2" Overlay Panel 44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

C

Dispenser

Cutout

Freezer

Panel

Fresh

Food

Panel

9 5/8"

1/4" BACKER ASSEMBLY ROUTING DIMENSIONS

A B C D E

DISPENSER CUTOUT

(39.1)

POSITION

F G

17 23/32" 3 3/8"

FLUSH INSET INSTALLATION

NOTES

The 1/2" overlay panel must be secured to
a .10" spacer panel and a 1/4" thick backer
panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer

panel, left to right and top to bottom.
Secure the panels with glue.

• Refer to the chart for locating the backer

panel to the overlay panel. Secure the
overlay panel to the backer panel with glue
and screws. Screws must be countersunk
into the backer panel.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.

Hinge Side

C

Backer with
Overlay Panel
Assembly

Freezer
Back

D

A

AB

Fresh Food
Back

PANEL DIMENSIONS

A B C D

Fresh Food Panel 2 1/16" 1/16" 1/8" 1/8"

Freezer Panel 2 1/16" 1/16" 1/8" 1/8"

Grille Panel 2 1/16" 2 1/16" 1 15/32" 7/32"

C

Door

1/4"

Backer

Panel

D

B

Grille Back

C

A B

1/2"

Overlay

Panel

.10"

Spacer

D

Product Specification Revised 5/16

*84"

(213.4)

42" (106.7)

25 1/2" (64.8)

23 7/8" (60.7)

1 3/4"

(4.4)

*72 1/4"

(183.5)

*3 1/2"

(8.9)

*83 1/2"

(212.1)

13 1/2"

(34.3)

*40"

(101.6)

68 1/2"

(174.0)

*3 3/4"

(9.5)

SIDE VIEWFRONT VIEW

* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

SPECIFICATIONS

Overall Width 42" (106.7 cm)

Overall Height 84" (213.36 cm)

Overall Depth 25 3/8" (64.453 cm)

Door Clearance 28 5/8" (72.1 cm)

Cutout Width 41 1/2" (105.4 cm)

Cutout Height 83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

Cutout Depth 24" (61 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 725 lb (328.9 kg)

OVERALL DIMENSIONS

STANDARD INSTALLATION

42" (106.7)

13 1/2"

(34.3)

*84"

(213.4)

(9.5)

*72 1/4"

(183.5)

*40"

(101.6)

68 1/2"

(174.0)

*3 3/4"

* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.

41" (104.2)

Case width

** Allow 13" (33.0) min
clearance for 130˚
door swing

25 1/2" (64.8)

23 7/8" (60.7)

1 3/4"

(4.4)

*3 1/2"

(8.9)

** Allow 19" (48.3) min
clearance for 130˚
door swing

SIDE VIEWFRONT VIEW

*83 1/2"

(212.1)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.

26 5/8"

(67.6)

TOP VIEW

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

Product Specification Revised 5/16

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

STANDARD INSTALLATION

3 1/8"

(7.93)

SIDE VIEW

24" (61)

1 9/16"

(3.97)

ANTI-TIP BRACKET

C

SOFFIT

SIDE VIEW INSTALLED

UNDER SOFFIT

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

*84 1/2"

*Trim will overlap

additional 7/16"

(214.6)

D

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

TOP VIEW

41 1/2" (105.4)

A

6"

(15.24)

5"

(12.7)

WATERW

FRONT VIEW

2" x 4"

Cut to 35" Length

Screws mounted
into vertical wall

studs

*84"

(213.4)

18" (45.7)

E

5"

(12.7)

75"

(190.5 )
From floor
to bottom

of electrical

area

3 1/2"

5"

(8.9)

(12.7)

B

Top Case Trim

Install Screws
Through Trim and Into
3/4" Min. Wood Brace

FRONT VIEW INSTALLED

WITH METAL WALL STUDS

AND NO SOFFIT

The refrigerator
will project
forward, slightly
beyond adjacent
cabinetry.

E

3/4"
Min.

Side View Top

Case Trim

STANDARD INSTALLATION

NOTES

A

Mounting the junction

box in this location will
also allow for front
accessibility through
access panel.

B

Water supply area.

WARNING:

The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.

The information below is
for cabinet design only.

When installing the anti­tip system you must use
the product installation
instructions.

Determine your installation
construction and required
anti-tip configuration:

C

Installed Under Soffit
After installing unit into
installation opening,
raise grille panel and
screw metal case sides to
adjacent cabinet. When
installed under a soffit, the
soffit cannot exceed 24"
deep. The top case trim
overlaps the bottom of
the soffit.

D

Wooden Wall Studs and

No Soffit

• Cut a 2" x 4" block and

secure to brackets
provided.

• Secure brackets to back

wall of opening at 84" or
your installation height
from the floor.

E

Metal Wall Studs and

No Soffit
This method requires
securely fastened cabinets
on both sides and a 3/4"
minimum wood brace
above unit, with it’s front
surface 24" from back wall.

• After installing unit into

opening, raise grille panel
and attach metal case
top trim to 3/4" minimum
wood brace.

• The brace spanning

the enclosure must be
securely fastened to
cabinets on both sides.

See Installation
Instructions for detailed
instructions.

Product Specification Revised 5/16

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

CUSTOM SIDE PANELS

F

24" (61.0)

3/16"

(.5)

1 7/8"

(4.8)

*3" - 4"

(7.6 - 10.2)

*Depending

on installation

height

*84”

*84"

(213.4)

(213.4)

*Depending

*Depending

on installation

on installation

height

STANDARD INSTALLATION

NOTES

F

Side panels must be

used whenever the sides

of the refrigerator will

be exposed. The 1/4"

side panels will slip

into the side case trim.

Secure the panels to

the refrigerator with

stick-on hook and loop

fastener strips. Order

the side panels from the

cabinet manufacturer.

2 9/16"

(6.5)

Product Specification Revised 5/16

1/4" Framed Panel

A

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

(24.4)

15 3/8"

(24.4)

15 3/8"

1/4" FRAMED PANEL DIMENSIONS

PANEL ASSEMBLY CROSS SECTION

Grille Panel

D E

Dispenser

Cutout

F

B

PANEL DIMENSIONS

G

Freezer

Panel

C

Fresh
Food
Panel

1/4" Framed Panel

Dispenser

Cutout

9 5/8"

Trim

A B C D E

39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

Door

Supplied Handles

DISPENSER CUTOUT

(39.1)

POSITION

F G

17 13/16" 3 1/8"

STANDARD INSTALLATION

NOTES

Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed custom door and grille
panels are required.

1/4" Framed Panels:

For 1/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

3/4" OVERLAY PANEL DIMENSIONS

A

Grille Panel

D E

G

F

Fresh
Food
Panel

Dispenser

Cutout

Freezer

Panel

3/4" Overlay Panels:

For 3/4" thick custom panels ordered from
your cabinet make; the decorative panels
slide into the trim.

The overlay panel must be secured to a
1/4"-thick backer panel which slides into

PANEL ASSEMBLY CROSS SECTION

B

1/4" Backer Panel

.10" Spacer Panel

Trim

Door

3/4" Overlay Panel

Supplied Handles

PANEL DIMENSIONS

A B C D E

C

1/4" Backer Panel

.10" Spacer Panel

3/4" Overlay Panel

.25" + .10" + .75" = 1.10" Total Panel Thickness

39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

39" 8 5/8" 67" 13 1/4" 23 1/4"

40 1/8" 9 3/4" 68 5/8" 14 13/16" 24 13/16"

* DISPENSER CUTOUT

Dispenser

Cutout

9 5/8"

(39.1)

POSITION

F G

17 15/16" 3 1/4"

* Cut the dispenser opening after the backer, spacer

and overlay panels have been assembled.

the trim. A spacer panel 0.10" thick must
be placed between the overlay and
backer panels.

Center each panel over the other. Assemble
the panels with glue and screws. Screws
must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Door Handles:

The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" overlay panels.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" overlay panels.

Kits include one handle. Order 2 kits for side­by-side refrigerators from your Monogram
supplier.

Product Specification Revised 5/16

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

DISPENSER TRIM

1/4" Framed Panel

Freezer Door

Ice/Water Dispenser

1/4"

Total

Thickness

1/4" Backer Panel

.10" Spacer Panel

3/4" Overlay Panel

Freezer Door

Ice/Water Dispenser

1/4" PANEL DISPENSER TRIM 3/4" OVERLAY PANEL DISPENSER TRIM

A B

RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS

1/4" Backer Panel
.10" Spacer

3/4" Overlay Panel

16 3/4"

1.10"

Total

Thickness

STANDARD INSTALLATION

NOTES

These refrigerators are supplied with two
dispenser trims, one for framed panels
and one for overlay panels.

1/4" Panel Dispenser Trim:

The framed panel must be 1/4" nominal
thickness to fit the dispenser trim.

• The dispenser trim ts over the custom

panel and snaps into the freezer door.

• If the panel is less than 0.250" thick, a

noticeable gap may be created around
the dispenser trim. Foam tape may be
applied on the door to improve the fit.

• If the panel is more than 0.250" thick,
the dispenser trim cannot be secured
to the door.

3/4" Overlay Panel Dispenser Trim:

The 3/4" overlay dispenser trim is
designed to fit a total panel thickness
of 1.100".

10 5/8"

DISPENSER TRIM

1.10”

Total

C

Thickness

D

SIDE VIEW CROSS SECTION

(Showing Raised Overlay

with Middle Rail)

• If the panel is less than 1.100" thick, a

noticeable gap may be created around
the dispenser trim.

• If the panel is more than 1.100" thick,

the dispenser trim cannot be secured
to the door.

• The overlay panel must be constructed

according to the specifications shown
to achieve the correct total thickness.

• Alternative panel construction methods

such as securing a 3/4" panel to a 1/4"
backer panel cannot be used. Another
method, routing a 3/4"-thick panel
on all sides, cannot be used. These
methods will not result in the required

1.100" panel thickness.

• When a raised panel design is to be

used, a custom middle rail is required.

Raised Overlay Panel Design on
Dispenser Models:

When a raised panel design is to be used,
a custom wide middle rail is required to
accept the dispenser trim.

• The middle rail must be wide enough to

allow for the dispenser trim to overlap
the opening.

• The middle rail must be 1.10" total

thickness to accept the dispenser trim.

Product Specification Revised 5/16

FEATURES AND BENEFITS

Halogen Light Columns - Located in the freezer
and fresh food compartments, extend the full
length of the interior compartments providing
brilliant, all-level illumination

LED Lighting - Located at the top of the fresh
food compartment, and inside the vegetable and
climate-control drawers, illuminates contents
without compromising space

Advanced Temperature Management System
with Multi-Shelf Air Tower - Provides even

distribution of air throughout the refrigerator

Climate-Control Drawer - Allows you to express­chill beverages, express-thaw meats and select
specific temperatures for perishable foods

ZISB420DHMonogram® 42" Built-In Side-by-Side Refrigerator

Dispenser with Proximity Sensor - Designed
to accommodate glassware of all sizes, from
pitchers to tumblers; control graphics light up as
you approach and automatically switch off when
you walk away

Dairy Bin with Center Divider - Has a unique
magnetic seal that locks in freshness

Filter-Change Indicator Light - Located on the
upfront control panel, provides a visual reminder
when it's time to replace the filter for the water
dispenser

GE® Water Filter - Has been moved from the
fresh food compartment to the overhead cabinet,
where it is discreetly out of sight

Drop-Down Shelf - Provides additional space
for a casserole dish or pizza box

R

Product Specification Revised 5/16