Monogram ZIS480NH Specification Sheet

SECTION 1

FLUSH INSET INSTALLATION

ZIS480NHMonogram® 48" Built-In Side-by-Side Refrigerator

SECTION 2

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

access is maintained, but pan removal is restricted.

ZIS480NH

SPECIFICATIONS

Overall Width 50" (127.0 cm)

Overall Height 84 1/2" (214.6 cm)

Overall Depth 26" (66.0 cm)

Door Clearance 28 5/8" (72.1 cm)

Cutout Width 51" (129.5 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 775 lb (351.5 kg)

† Dimensions include 3/4" custom cabinet panel

†

OVERALL DIMENSIONS
AFTER PANEL INSTALL

FLUSH INSET INSTALLATION

26" (66.0)

**20"

(50.8)

20 5/8" (52.4)

* 83 1/2"

(212.1)

SIDE VIEW

50" (127.0)

11 11/16"

(29.7)

72 5/8"

68 5/8"

(174.3)

(184.5)

4"

(10.2)

84 1/2"

(214.6)

†

†

FRONT VIEW

Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84".

47" (119.4)

Case width

**15"

(38.1)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.

*115° Door swing

Doors can be adjusted to

90° door swing

28 5/8"

(72.7)

TOP VIEW

** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.

** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )
From floor
to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

ZIS480NH

FLUSH INSET INSTALLATION 3/4" PANELS

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

85"

(215.9)

Finished cleats

3 1/2"

W

ANTI-TIP BRACKET

C

SOFFIT

(8.9)

5 1/4" (13.3)

3/4" (1.9)

Width of side cleats

85"

(215.9)

3/4" Panel

7"

(17.8)

D

TOP VIEW

Finished cleats

Case Trim

6"

(15.2)

Case

Door

51" (129.5) Flush inset width

49 1/2" (125.7)

Width between cleats

E

5"

(12.7)

WATER

FRONT VIEWSIDE VIEW

22 1/4"

(56.5)

7"

(17.8)

B

2" x 4"

Cut to 35" Length

1/2" (1.3)

From floor
to bottom

of electrical

3 1/2"

(8.9)

75"

(190.5 )

area

FLUSH INSET INSTALLATION

NOTES

A

Mounting the junction box in this

location will also allow for front
accessibility through access panel.

B

Water supply area.

A

WARNING:

The refrigerator is top heavy and must
be secured to prevent the possibility
of tipping forward. Failure to do so
may result in death or serious injury.

The information below is for cabinet
design only. When installing the

anti-tip system you must use the
product installation instructions.

Determine your installation construction
and required anti-tip configuration:

C

Cut a 1" x 4" block 35" long.

Measure and mark under the soffit,
5 1/4" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom
of the block to the finished floor
should measure 84".

D

Wooden Wall Studs and No Soffit

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.

See Installation Instructions for
detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

*84"

(213.4)

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

Screws mounted
into vertical wall

studs

Product Specification Revised 5/16

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )
From floor
to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH

FLUSH INSET INSTALLATION 1/2" PANELS

26 3/16" (66.5)

Flush inset depth

20 13/16" (52.9)

Depth to cleat

85"

(215.9)

Finished cleats

3 1/2"

(8.9)

W

ANTI-TIP BRACKET

C

SOFFIT

5 3/8" (13.7)

3/4" (1.9)

Width of side cleats

85"

(215.9)

Finished cleats

Case Trim

1/2" Panel

6"

(15.2)

7"

(17.8)

D

TOP VIEW

Case

Door

51" (129.5) Flush inset width

49 1/2" (125.7)

Width between cleats

E

22 1/4"

5"

(12.7)

(56.5)

B

WATER

FRONT VIEWSIDE VIEW

2" x 4"

Cut to 35" Length

7"

(17.8)

1/2" (1.3)

A

75"

(190.5 )

From floor

to bottom

of electrical

area

3 1/2"

(8.9)

FLUSH INSET INSTALLATION

NOTES

A

Mounting the junction box in this

location will also allow for front
accessibility through access panel.

B

Water supply area.

WARNING:

The refrigerator is top heavy and must
be secured to prevent the possibility
of tipping forward. Failure to do so may
result in death or serious injury.

The information below is for cabinet
design only. When installing the

anti-tip system you must use the
product installation instructions.

Determine your installation
construction and required anti-tip
configuration:

C

Cut a 1" x 4" block 35" long.

Measure and mark under the soffit,
5 3/8" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom of
the block to the finished floor should
measure 84".

D

Wooden Wall Studs and No Soffit

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of

opening at 84" or your installation
height from the floor.

See Installation Instructions for
detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

*84"

(213.4)

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

Screws mounted
into vertical wall

studs

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH

HINGE

HANDLE

Front

DETAIL BOTTOM

FLUSH INSET 3/4" PANEL DIMENSIONS

A

Grille Panel

D E

Freezer

Panel

Fresh

Food

Panel

B

PANEL DIMENSIONS

A B C D E

50" 11 3/16" 68 5/8" 20 7/8" 28 7/8"

C

3/4" RAISED DOOR PANEL ROUTING

DETAIL TOP

3/4"

11/32"

1/4"

7/16"

1/4"

NOTE: Routed areas should be
finished as they may be visible
when assembled.

Front

TOP

FLUSH INSET INSTALLATION

NOTES

Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed 1/2" or 3/4” custom door
and grille panels are required. For 3/4"
raised door and grille panels, routing is
required. The router depth is 1/4" all the
way around the panel’s backs. Additional
panel width reductions are required per the
diagrams shown. This will create “picture
frame” routing allowing the panels to slide
into the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.

Door Handles

Door handle not included. A custom handle
supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4” panels. Kit includes

one handle – 30 1/2” long.

ZKHSS2: European tubular stainless steel
handle designed to fit 3/4” panels. Kit includes

one handle – 64 1/4” long.

3/16"

DETAIL HINGE

SIDE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

Back

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

3/16"

FrontBack

DETAIL HANDLE

SIDE

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

“PICTURE FRAME” ROUTING

ZIS480NH

3/4" RAISED GRILLE PANEL ROUTING

NOTE: Routed areas should be
finished as they may be visible
when assembled.

Front

Back

CORNER VIEW SHOWING

DETAIL

LEFT SIDE

2"

3/16"

DETAIL BOTTOM

DETAIL TOP

ROUTER DEPTH 1/4"

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

DETAIL RIGHT

SIDE

TOP

FLUSH INSET INSTALLATION

NOTES

Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door and grille panels are
required. For 3/4" raised door and grille
panels, routing is required. The router
depth is 1/4" all the way around the
panel’s backs. Additional panel width

FrontBack

reductions are required per the diagrams
shown. This will create “picture frame”
routing allowing the panels to slide into
the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.

Door Handles

Door handle not included. A custom
handle supplied by your cabinet maker
may be used.

ZKHPSS1: Professional tubular stainless
steel handle designed to fit 3/4" panels.

Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit

includes one handle – 64 1/4" long.

LEFT
SIDE

ROUTER DEPTH 1/4"

2 1/16" 2 1/16"

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

ROUTER DEPTH 1/4"

RIGHT

SIDE

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

ZIS480NH

FLUSH INSET 1/2" PANEL DIMENSIONS

A

PANEL DIMENSIONS

Grille Panel

D E

Freezer

Panel

Fresh

Food

Panel

B

1/4" Backer Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 29 9/16"

.10" Space Panel 45" 8 5/8" 67" 17 9/16" 25 9/16"

1/2" Overlay Panel 50" 11 3/16" 68 5/8" 20 7/8" 28 7/8"

C

1/4" BACKER ASSEMBLY ROUTING DIMENSIONS

A B C D E

FLUSH INSET INSTALLATION

NOTES

The 1/2" overlay panel must be secured to
a .10" spacer panel and a 1/4" thick backer
panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer

panel, left to right and top to bottom.
Secure the panels with glue.

• Refer to the chart for locating the backer

panel to the overlay panel. Secure the
overlay panel to the backer panel with glue
and screws. Screws must be countersunk
into the backer panel.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.

Hinge Side

C

Freezer
Back

D

Backer with
Overlay Panel
Assembly

A

AB

Fresh Food
Back

PANEL DIMENSIONS

A B C D

Fresh Food Panel 2 1/16" 1/16" 1/8" 1/8"

Freezer Panel 2 1/16" 1/16" 1/8" 1/8"

Grille Panel 2 1/16" 2 1/16" 1 15/32" 7/32"

C

Door

1/4"

Backer

Panel

D

B

Grille Back

C

A B

1/2"

Overlay

Panel

.10"

Spacer

D

Product Specification Revised 5/16

*84"

(213.4)

48" (121.9)

25 1/2" (64.8)
23 7/8" (60.7)

1 3/4"

(4.4)

*72 1/4"

(183.5)

*3 1/2"

(8.9)

*83 1/2"

(212.1)

68 1/2"

(174.0)

*3 3/4"

(9.5)

SIDE VIEWFRONT VIEW

* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.

maintained, but pan removal is restricted.

Monogram® 48" Built-In Side-by-Side Refrigerator ZIS480NH

SPECIFICATIONS

Overall Width 48" (121.92 cm)

Overall Height 84" (213.36 cm)

Overall Depth 25 3/8" (64.453 cm)

Door Clearance 28 5/8" (72.1 cm)

Cutout Width 47 1/2" (120.7 cm)

Cutout Height 83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

Cutout Depth 24" (61 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 775 lb

OVERALL DIMENSIONS
AFTER PANEL INSTALL

STANDARD INSTALLATION

48" (121.9)

*84"

(213.4)

68 1/2"

(174.0)

*3 3/4"

(9.5)

* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.

47" (119.4)

Case width

*72 1/4"

(183.5)

** Allow 15" (38.1) min
clearance for 130˚
door swing

25 1/2" (64.8)
23 7/8" (60.7)

1 3/4"

(4.4)

*3 1/2"

(8.9)

** Allow 20" (50.8) min
clearance for 130˚
door swing

SIDE VIEWFRONT VIEW

*83 1/2"

(212.1)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.

28 5/8"

TOP VIEW

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

Product Specification Revised 5/16

(72.7)

Monogram® 48" Built-In Side-by-Side Refrigerator

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

ZIS480NH

STANDARD INSTALLATION

3 1/8"

(7.93)

1 9/16"

SIDE VIEW

24" (61)

(3.97)

ANTI-TIP BRACKET

C

SOFFIT

SIDE VIEW INSTALLED

UNDER SOFFIT

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

*84 1/2"

*Trim will overlap

additional 7/16"

(214.6)

5"

(12.7)

D

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

TOP VIEW

47 1/2" (120.7)

A

6"

(15.24)

E

5"

(12.7)

WATERW

FRONT VIEW

2" x 4"

Cut to 35" Length

Screws mounted
into vertical wall

studs

*84"

(213.4)

20" (50.8)

B

5"

(12.7)

From floor

to bottom

of electrical

3 1/2"

(8.9)

Top Case Trim

Install Screws

Through Trim and Into

3/4" Min. Wood Brace

FRONT VIEW INSTALLED

WITH METAL WALL STUDS

AND NO SOFFIT

75"

(190.5 )

area

The refrigerator
will project
forward, slightly
beyond adjacent
cabinetry.

E

3/4"
Min.

Side View Top

Case Trim

STANDARD INSTALLATION

NOTES

A

Mounting the junction

box in this location will
also allow for front
accessibility through
access panel.

B

Water supply area.

WARNING:

The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.

The information below is
for cabinet design only.

When installing the anti­tip system you must use
the product installation
instructions.

Determine your installation
construction and required
anti-tip configuration:

C

Installed Under Soffit
After installing unit into
installation opening,
raise grille panel and
screw metal case sides to
adjacent cabinet. When
installed under a soffit, the
soffit cannot exceed 24"
deep. The top case trim
overlaps the bottom of the
soffit.

D

Wooden Wall Studs and

No Soffit

• Cut a 2" x 4" block and

secure to brackets
provided.

• Secure brackets to back

wall of opening at 84" or
your installation height
from the floor.

E

Metal Wall Studs and

No Soffit
This method requires
securely fastened cabinets
on both sides and a 3/4”
minimum wood brace
above unit, with it’s front
surface 24" from back wall.

• After installing unit into

opening, raise grille panel
and attach metal case
top trim to 3/4" minimum
wood brace.

• The brace spanning

the enclosure must be
securely fastened to
cabinets on both sides.

See Installation
Instructions for detailed
instructions.

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

ZIS480NH

CUSTOM SIDE PANELS

F

24" (61.0)

3/16"

(.5)

1 7/8"

(4.8)

*3" - 4"

(7.6 - 10.2)

*Depending

on installation

height

*84”

*84"

(213.4)

(213.4)

*Depending

*Depending

on installation

on installation

height

STANDARD INSTALLATION

NOTES

F

Side panels must be used whenever

the sides of the refrigerator will be
exposed. The 1/4" side panels will
slip into the side case trim. Secure
the panels to the refrigerator with
stick-on hook and loop fastener
strips. Order the side panels from
the cabinet manufacturer.

2 9/16"

(6.5)

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

1/4" Framed Panel

ZIS480NH

1/4" FRAMED PANEL DIMENSIONS

A

Grille Panel

D E

B

PANEL ASSEMBLY CROSS SECTION

PANEL DIMENSIONS

C

Freezer

Panel

Fresh

Food

Panel

Trim

1/4" Framed Panel

Door

Supplied Handles

A B C D E

45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"

STANDARD INSTALLATION

NOTES

Trimmed refrigerators are designed to be
customized with decorative panels. Field­installed custom door and grille panels are
required.

1/4" Framed Panels:

For 1/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

3/4" OVERLAY PANEL DIMENSIONS

A

Grille Panel

D E

B

PANEL ASSEMBLY CROSS SECTION

1/4" Backer Panel

.10" Spacer Panel

PANEL DIMENSIONS

1/4" Backer Panel

.10" Spacer Panel

3/4" Overlay Panel

.25" + .10" + .75" = 1.10" Total Panel Thickness

Freezer

Panel

C

Fresh

Food

Panel

Trim

45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"

45" 8 5/8" 67" 17 1/4" 25 1/4"

46 1/8" 9 3/4" 68 5/8" 18 13/16" 26 13/16"

Door

3/4" Overlay Panel

Supplied Handles

A B C D E

3/4" Overlay Panels:

For 3/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.

The overlay panel must be secured to a
1/4"-thick backer panel which slides into
the trim. A spacer panel 0.10" thick must
be placed between the overlay and backer
panels.

Center each panel over the other. Assemble
the panels with glue and screws. Screws must
be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Door Handles:

The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" overlay panels.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" overlay panels.

Kits include one handle. Order 2 kits for side­by-side refrigerators from your Monogram
supplier.

Product Specification Revised 5/16

Monogram® 48" Built-In Side-by-Side Refrigerator

FEATURES AND BENEFITS

Halogen Light Columns - Located in the freezer
and fresh food compartments, extend the full
length of the interior compartments providing
brilliant, all-level illumination

LED Lighting - Located at the top of the fresh
food compartment, and inside the vegetable and
climate-control drawers, illuminates contents
without compromising space

Advanced Temperature Management System
with Multi-Shelf Air Tower - Provides even

distribution of air throughout the refrigerator

Climate-Control Drawer - Allows you to express­chill beverages, express-thaw meats and select
specific temperatures for perishable foods

ZIS480NH

Dispenser with Proximity Sensor - Designed
to accommodate glassware of all sizes, from
pitchers to tumblers; control graphics light up as
you approach and automatically switch off when
you walk away

Dairy Bin with Center Divider - Has a unique
magnetic seal that locks in freshness

Filter-Change Indicator Light - Located on the
upfront control panel, provides a visual reminder
when it's time to replace the filter for the water
dispenser

GE® Water Filter - Has been moved from the
fresh food compartment to the overhead cabinet,
where it is discreetly out of sight

Drop-Down Shelf - Provides additional space for
a casserole dish or pizza box

R

Product Specification Revised 5/16