Monogram ZIS420NK Specsheet

SECTION 1

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

SECTION 2

FLUSH INSET INSTALLATION

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

*84"

(213.4)

42" (106.7)

25 1/2" (64.8)

23 7/8" (60.7)

1 3/4"

(4.4)

*72 1/4"

(183.5)

*3 1/2"

(8.9)

*83 1/2"

(212.1)

68 1/2"

(174.0)

*3 3/4"

(9.5)

SIDE VIEWFRONT VIEW

* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.

SPECIFICATIONS

Overall Width 42" (106.7 cm)

Overall Height 84" (213.36 cm)

Overall Depth 25 3/8" (64.453 cm)

Door Clearance 26 5/8" (67.6 cm)

Cutout Width 41 1/2" (105.4 cm)

Cutout Height 83 1/2" - 84 1/2"

Cutout Depth 24" (61 cm)

Plumbing Requirements 1/4" OD copper

Shipping Weight 725 lb (328.9 kg)

(212.1 - 214.6 cm)

tubing or GE
SmartConnect kit

OVERALL DIMENSIONS

42" (106.7)

*84"

(213.4)

(9.5)

41" (104.2)

Case width

*72 1/4"

(183.5)

68 1/2"

(174.0)

*3 3/4"

* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.

** Allow 13" (33.0) min
clearance for 130˚
door swing

STANDARD
INSTALLATION

25 1/2" (64.8)

23 7/8" (60.7)

1 3/4"

(4.4)

*83 1/2"

*3 1/2"

(8.9)

** Allow 19" (48.3) min
clearance for 130˚
door swing

SIDE VIEWFRONT VIEW

(212.1)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
recessed into the back wall.

26 5/8"

(67.6)

TOP VIEW

4" (10.2) min

** Allow

clearance to a wall for 90˚

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )
From floor
to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

AND NO SOFFIT

STANDARD INSTALLATION

3 1/8"

(7.93)

The refrigerator will project forward, slightly beyond adjacent cabinetry.

ANTI-TIP BRACKET

SIDE VIEW INSTALLED

UNDER SOFFIT

24" (61)

1 9/16"

(3.97)

SIDE VIEW

C

SOFFIT

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

*84 1/2"

(214.6)

*Trim will overlap

additional 7/16"

D

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

TOP VIEW

41 1/2" (105.4)

A

6"

(15.24)

5"

(12.7)

WATERW

FRONT VIEW

2" x 4"

Cut to 35" Length

Screws mounted
into vertical wall

studs

*84"

(213.4)

18" (45.7)

E

5"

(12.7)

B

5"

(12.7)

From floor
to bottom

of electrical

3 1/2"

(8.9)

Top Case Trim

Install Screws

Through Trim and Into

3/4" Min. Wood Brace

FRONT VIEW INSTALLED

WITH METAL WALL STUDS

AND NO SOFFIT

75"

(190.5 )

area

E

3/4"
Min.

Side View Top

Case Trim

STANDARD
INSTALLATION

NOTES

A

Mounting the junction box in

this location will also allow
for front accessibility through
access panel.

B

Water supply area.

WARNING:

The refrigerator is top heavy
and must be secured to prevent
the possibility of tipping forward.
Failure to do so may result in
death or serious injury.

The information below is for
cabinet design only. When
installing the anti-tip system you
must use the product installation
instructions.

Determine your installation
construction and required
anti-tip configuration:

C

Installed Under Sot

After installing unit into
installation opening, raise grille
panel and screw metal case
sides to adjacent cabinet. When
installed under a sot, the sot
cannot exceed 24" deep. The top
case trim overlaps the bottom of
the sot.

D

Wooden Wall Studs and No

Sot

• Cut a 2" x 4" block and secure

to brackets provided.

• Secure brackets to back wall

of opening at 84" or your
installation height from the
floor.

E

Metal Wall Studs and No Sot

This method requires securely
fastened cabinets on both sides
and a 3/4" minimum wood brace
above unit, with it’s front surface
24" from back wall.

• After installing unit into

opening, raise grille panel and
attach metal case top trim to
3/4" minimum wood brace.

• The brace spanning the

enclosure must be securely
fastened to cabinets on both
sides.

See Installation Instructions for
detailed instructions.

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

CUSTOM SIDE PANELS

F

1 7/8"

(4.8)

*3" - 4"

(7.6 - 10.2)

*Depending

on installation

height

24" (61.0)

3/16"

(.5)

*Depending

*Depending

on installation

on installation

*84”

*84"

(213.4)

(213.4)

height

STANDARD
INSTALLATION

NOTES

F

Side panels must be used

whenever the sides of the
refrigerator will be exposed.
The 1/4" side panels will slip into
the side case trim. Secure the
panels to the refrigerator with
stick-on hook and loop fastener
strips. Order the side panels
from the cabinet manufacturer.

2 9/16"

(6.5)

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

Door

1/4" Backer Panel

.10" Spacer Panel

Supplied Handles

Trim

3/4" Overlay Panel

Door

1/4" Framed Panel

Supplied Handles

Trim

1/4" FRAMED PANEL DIMENSIONS

A

Grille Panel

B

D E

C

Fresh

Freezer

Panel

Food

Panel

3/4" OVERLAY PANEL DIMENSIONS

A

B

C

Grille Panel

D E

Freezer

Panel

Fresh

Food

Panel

PANEL ASSEMBLY CROSS SECTION

PANEL DIMENSIONS

A B C D E

1/4" Framed Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

PANEL ASSEMBLY CROSS SECTION

PANEL DIMENSIONS

A B C D E

1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

.10" Spacer Panel 39" 8 5/8" 67" 13 1/4" 23 1/4"

3/4" Overlay Panel 40 1/8" 9 3/4" 68 5/8" 14 13/16" 24 13/16"

.25" + .10" + .75" = 1.10" Total Panel Thickness

STANDARD
INSTALLATION

NOTES

Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed custom door
and grille panels are required.

1/4" Framed Panels:
1/4" thick custom panels ordered
from your cabinet maker. The
decorative panels slide into the trim

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

3/4" Overlay Panels:
3/4" thick custom panels ordered
from your cabinet maker. The
decorative panels slide into the trim

The overlay panel must be secured to
a 1/4"-thick backer panel which slides
into the trim. A spacer panel 0.10"
thick must be placed between the
overlay and backer panels. Center
each panel over the other. Assemble
the panels with glue and screws.
Screws must be countersunk into the
backer panel.

NOTE: Left-to-right oset is not
always equal to top-to-bottom oset.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Door Handles:
The supplied handles can be
adjusted to accommodate both
framed or overlay panels. Custom
handles of your choice, supplied
by your cabinet maker, can also be
installed.
ZKHPSS1: Professional tubular
stainless steel handle designed to fit
3/4" overlay panels.
ZKHSS2: European tubular stainless
steel handle designed to fit
3/4" overlay panels.

Kits include one handle. Order 2 kits
for side-by-side refrigerators from
your Monogram supplier.

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

SPECIFICATIONS

Overall Width 44" (111.8 cm)†

Overall Height 84 1/2" (214.6 cm) †

Overall Depth 26" (66.0 cm) †

Door Clearance 26 5/8" (67.6 cm)

Cutout Width 45" (114.3 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE
SmartConnect kit

Shipping Weight 725 lb (328.9 kg)

† Dimensions include 3/4" custom cabinet panel

OVERALL DIMENSIONS
AFTER PANEL INSTALL

FLUSH INSET
INSTALLATION

44" (111.8)

11 11/16"

(29.7)

68 5/8"

(174.3)

72 5/8"

(184.5)

*4"

(10.2)

**19"

(48.3)

84 1/2"

(214.6)

FRONT VIEW

* Shipping height . Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84".

41" (104.2)

Case width

**13"

(33.0)

26" (66.0)

20 5/8" (52.4)

*83 1/2"

(212.1)

SIDE VIEW

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
recessed into the back wall.

*115° Door swing

Doors can be adjusted to

90° door swing

26 5/8"

(67.6)

TOP VIEW

** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.

** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )
From floor
to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

AND NO SOFFIT

FLUSH INSET INSTALLATION
3/4" PANELS

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

Finished cleats

W

C

SOFFIT

85"

(215.9)

ANTI-TIP BRACKET

3 1/2"

(8.9)

5 1/4" (13.3)

3/4" (1.9)

Width of side cleats

85"

(215.9)

D

TOP VIEW

Finished cleats

Case Trim

3/4" Panel

(15.2)

7"

(17.8)

Case

Door

45" (114.3) Flush inset width

43 1/2" (110.5)

Width between cleats

6"

E

5"

(12.7)

WATER

FRONT VIEWSIDE VIEW

Screws mounted
into vertical wall

*84"

(213.4)

*Or installation

height from floor

19"

(48.3)

7"

(17.8)

B

2" x 4"

Cut to 35" Length

studs

1/2" (1.3)

From floor
to bottom

of electrical

3 1/2"

(8.9)

75"

(190.5 )

area

FLUSH INSET
INSTALLATION

NOTES

A

Mounting the junction box in this

location will also allow for front
accessibility through access panel.

B

Water supply area.

A

WARNING:

The refrigerator is top heavy and
must be secured to prevent the
possibility of tipping forward.
Failure to do so may result in
death or serious injury.

The information below is for cabinet
design only. When installing the
anti-tip system you must use the
product installation instructions.

Determine your installation
construction and required anti-tip
configuration:

C

Cut a 1" x 4" block 35" long.

Measure and
mark under the sot,
5 1/4" from the front edge of the
cabinet. Secure the wood block
under the sot. From the bottom
of the block to the finished floor
should measure 84".

D

Wooden Wall Studs and No Sot

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of

opening at 84" or your installation
height from the floor.

See Installation Instructions for
detailed instructions.

SIDE VIEW INSTALLED

UNDER SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FRONT VIEW SIDE VIEW

W

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

E

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

6"

(15.2)

5"

(12.7)

5"

(12.7)

5"

(12.7)

FLUSH INSET INSTALLATION
1/2" PANELS

26 3/16" (66.5)

Flush inset depth

20 13/16" (52.9)

Depth to cleat

Finished cleats

W

C

SOFFIT

85"

(215.9)

ANTI-TIP BRACKET

3 1/2"

(8.9)

3/4" (1.9)

Width of side cleats

5 3/8" (13.7)

85"

(215.9)

Finished cleats

Case Trim

1/2" Panel

45" (114.3) Flush inset width

Width between cleats

6"

(15.2)

7"

(17.8)

FRONT VIEWSIDE VIEW

D

TOP VIEW

Case

Door

43 1/2" (110.5)

E

5"

(12.7)

B

WATER

2" x 4"

Cut to 35" Length

19"

(48.3)

7"

(17.8)

1/2" (1.3)

From floor
to bottom

of electrical

3 1/2"

(8.9)

75"

(190.5 )

area

FLUSH INSET
INSTALLATION

NOTES

A

Mounting the junction box in

this location will also allow
for front accessibility through
access panel.

B

A

Water supply area.

WARNING:

The refrigerator is top heavy and
must be secured to prevent the
possibility of tipping forward.
Failure to do so may result in
death or serious injury.

The information below is for
cabinet design only. When
installing the anti-tip system you
must use the product installation
instructions.

Determine your installation
construction and required anti-tip
configuration:

C

Cut a 1" x 4" block 35" long.

Measure and mark under the
sot, 5 3/8" from the front
edge of the cabinet. Secure the
wood block under the sot.
From the bottom of the block
to the finished floor should
measure 84".

SIDE VIEW INSTALLED

UNDER SOFFIT

*84"

(213.4)

*Or installation

height from floor

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

Screws mounted
into vertical wall

studs

D

Wooden Wall Studs and No

Sot

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall

of opening at 84" or your
installation height from the floor.

See Installation Instructions for
detailed instructions.

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

HINGE

HANDLE

Front

DETAIL BOTTOM

FLUSH INSET 3/4" PANEL DIMENSIONS

A

Grille Panel

D E

Freezer

Panel

Fresh

Food

Panel

B

PANEL DIMENSIONS

A B C D E

44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

C

3/4" RAISED DOOR PANEL ROUTING

DETAIL TOP

NOTE: Routed areas should be
finished as they may be visible
when assembled.

11/32"

1/4"

3/4"

1/4"

7/16"

Front

TOP

FLUSH INSET
INSTALLATION

NOTES

Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door and grille panels are
required. For 3/4" raised door and
grille panels, routing is required.
The router depth is 1/4" all the
way around the panel’s backs.
Additional panel width reductions
are required per the diagrams
shown. This will create “picture
frame” routing allowing the panels
to slide into the attached door and
grille trims.

MAXIMUM TOTAL PANEL WEIGHT:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

DOOR HANDLES
Door handle not included. A
custom handle supplied by your
cabinet maker may be used.

ZKHPSS1: Professional tubular
stainless steel handle designed to
fit 3/4" panels. Kit includes one

handle – 30 1/2" long.

3/16"

DETAIL HINGE

SIDE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

Back

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

3/16"

ZKHSS2: European tubular stainless
steel handle designed to fit
3/4" panels. Kit includes one

handle – 64 1/4" long.

FrontBack

DETAIL HANDLE

SIDE

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

“PICTURE FRAME” ROUTING

3/4" RAISED GRILLE PANEL ROUTING

NOTE: Routed areas should be
finished as they may be visible
when assembled.

Front

2"

Back

CORNER VIEW SHOWING

3/16"

DETAIL BOTTOM

DETAIL TOP

ROUTER DEPTH 1/4"

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

FLUSH INSET
INSTALLATION

NOTES

Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door and grille panels are
required. For 3/4" raised door and
grille panels, routing is required.
The router depth is 1/4" all the
way around the panel’s backs.
Additional panel width reductions
are required per the diagrams
shown. This will create “picture
frame” routing allowing the panels
to slide into the attached door and
grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Door Handles
Door handle not included. A
custom handle supplied by your
cabinet maker may be used.

LEFT
SIDE

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

ROUTER DEPTH 1/4"

2 1/16" 2 1/16"

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

DETAIL RIGHT

SIDE

RIGHT

SIDE

ZKHPSS1: Professional tubular
stainless steel handle designed to
fit 3/4" panels. Kit includes one

handle – 30 1/2" long.

ZKHSS2: European tubular stainless
steel handle designed to fit
3/4" panels. Kit includes one

handle – 64 1/4" long.

Product Specification Revised 9/16

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

FLUSH INSET 1/2" PANEL DIMENSIONS

A

PANEL DIMENSIONS

Grille Panel

D E

B

A B C D E

1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

.10" Space Panel 39" 8 5/8" 67" 13 9/16" 23 9/16"

1/2" Overlay Panel 44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

C

Fresh

Freezer

Panel

Food

Panel

1/4" BACKER ASSEMBLY ROUTING DIMENSIONS

Hinge Side

FLUSH INSET
INSTALLATION

NOTES

The 1/2" overlay panel must be
secured to a .10" spacer panel and a
1/4" thick backer panel, which slides
into the trim.

Assemble the panels with glue and
screws:

• Center the spacer panel on the

backer panel, left to right and
top to bottom. Secure the panels
with glue.

• Refer to the chart for locating the

backer panel to the overlay panel.
Secure the overlay panel to the
backer panel with glue and screws.
Screws must be countersunk into
the backer panel.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

C

Freezer
Back

D

Backer with
Overlay Panel
Assembly

A

AB

C

Fresh Food

Back

PANEL DIMENSIONS

A B C D

Fresh Food Panel 2 1/16" 1/16" 1/8" 1/8"

Freezer Panel 2 1/16" 1/16" 1/8" 1/8"

Grille Panel 2 1/16" 2 1/16" 1 15/32" 7/32"

Door

1/4"

Backer

Panel

D

B

Grille Back

C

A B

1/2"

Overlay

Panel

.10"

Spacer

D

Product Specification Revised 9/16

FEATURES AND BENEFITS

LED LIGHTING
Light columns in the freezer and fresh food
compartments extend the full length of
the interior and LED lighting located inside
the vegetable and climate-control drawers
illuminate contents without compromising
space

ADVANCED TEMPERATURE MANAGEMENT
SYSTEM WITH MULTI-SHELF AIR TOWER
Provides even distribution of air throughout the
refrigerator

CLIMATE-CONTROL DRAWER
Allows you to express-chill beverages, express­thaw meats and select specific temperatures
for perishable foods

DISPENSER WITH PROXIMITY SENSOR
Designed to accommodate glassware of
all sizes, from pitchers to tumblers; control
graphics light up as you approach and
automatically switch o when you walk away

ZIS420NKMONOGRAM 42" BUILT-IN SIDE-BY-SIDE REFRIGERATOR

DAIRY BIN WITH CENTER DIVIDER
Has a unique magnetic seal that locks in
freshness

FILTER-CHANGE INDICATOR LIGHT
Located on the upfront control panel, provides
a visual reminder when it's time to replace the
filter for the water dispenser

GE® WATER FILTER
Has been moved from the fresh food
compartment to the overhead cabinet, where it
is discreetly out of sight

R

Product Specification Revised 9/16