Monogram ZIS420NH Specification Sheet
SECTION 1
FLUSH INSET INSTALLATION
ZIS420NHMonogram® 42" Built-In Side-by-Side Refrigerator
SECTION 2
STANDARD INSTALLATION
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
Product Specification Revised 5/16
ZIS420NHMonogram® 42" Built-In Side-by-Side Refrigerator
SPECIFICATIONS
Overall Width 44" (111.8 cm)
Overall Height 84 1/2" (214.6 cm)
Overall Depth 26" (66.0 cm)
Door Clearance 26 5/8" (67.6 cm)
Cutout Width 45" (114.3 cm)
Cutout Height 85" (215.9 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 725 lb (328.9 kg)
† Dimensions include 3/4" custom cabinet panel
†
OVERALL DIMENSIONS
AFTER PANEL INSTALL
FLUSH INSET INSTALLATION
26" (66.0)
44" (111.8)
11 11/16"
(29.7)
68 5/8"
(174.3)
72 5/8"
(184.5)
*4"
(10.2)
**19"
(48.3)
84 1/2"
(214.6)
†
†
FRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84".
41" (104.2)
Case width
**13"
(33.0)
20 5/8" (52.4)
*83 1/2"
(212.1)
SIDE VIEW
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
*115° Door swing
Doors can be adjusted to
90° door swing
26 5/8"
(67.6)
TOP VIEW
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
Product Specification Revised 5/16
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZIS420NHMonogram® 42" Built-In Side-by-Side Refrigerator
FLUSH INSET INSTALLATION 3/4" PANELS
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
85"
(215.9)
Finished cleats
3 1/2"
(8.9)
W
ANTI-TIP BRACKET
C
SOFFIT
3/4" (1.9)
Width of side cleats
5 1/4" (13.3)
85"
(215.9)
TOP VIEW
Finished cleats
Case Trim
3/4" Panel
(15.2)
7"
(17.8)
Case
Door
45" (114.3) Flush inset width
6"
43 1/2" (110.5)
Width between cleats
E
5"
(12.7)
WATER
FRONT VIEWSIDE VIEW
D
19"
(48.3)
B
2" x 4"
Cut to 35" Length
7"
(17.8)
1/2" (1.3)
75"
(190.5 )
From floor
to bottom
of electrical
area
3 1/2"
(8.9)
A
FLUSH INSET INSTALLATION
NOTES
A
Mounting the junction box in this
location will also allow for front
accessibility through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
Determine your installation
construction and required anti-tip
configuration:
C
Cut a 1" x 4" block 35” long.
Measure and
mark under the soffit,
5 1/4" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom of
the block to the finished floor should
measure 84".
D
Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
See Installation Instructions for
detailed instructions.
SIDE VIEW INSTALLED
UNDER SOFFIT
*84"
(213.4)
*Or installation
height from floor
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
Screws mounted
into vertical wall
studs
Product Specification Revised 5/16
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZIS420NHMonogram® 42" Built-In Side-by-Side Refrigerator
FLUSH INSET INSTALLATION 1/2" PANELS
26 3/16" (66.5)
Flush inset depth
20 13/16" (52.9)
Depth to cleat
85"
(215.9)
Finished cleats
3 1/2"
(8.9)
W
ANTI-TIP BRACKET
C
SOFFIT
Width of side cleats
5 3/8" (13.7)
3/4" (1.9)
85"
(215.9)
TOP VIEW
Finished cleats
Case Trim
1/2" Panel
7"
(17.8)
45" (114.3) Flush inset width
43 1/2" (110.5)
Width between cleats
6"
(15.2)
(12.7)
WATER
FRONT VIEWSIDE VIEW
D
Case
Door
E
5"
B
19"
(48.3)
7"
(17.8)
2" x 4"
Cut to 35" Length
1/2" (1.3)
75"
(190.5 )
From floor
to bottom
of electrical
area
3 1/2"
(8.9)
FLUSH INSET INSTALLATION
NOTES
A
Mounting the junction box in this
location will also allow for front
accessibility through access panel.
B
Water supply area.
A
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
Determine your installation
construction and required anti-tip
configuration:
C
Cut a 1" x 4" block 35” long. Measure
and mark under the soffit,
5 3/8" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom of
the block to the finished floor should
measure 84".
D
Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
See Installation Instructions for
detailed instructions.
SIDE VIEW INSTALLED
UNDER SOFFIT
*84"
(213.4)
*Or installation
height from floor
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
Screws mounted
into vertical wall
studs
Product Specification Revised 5/16
Loading...