Monogram ZIRS360NBRH Specifications
36" (91.5)
25 3/4" (65.4)
23 7/8" (60.7)
64 1/4"
(163.2)
*6 1/2"
(16.5)
*84"
(213.4)
*73 1/4"
(186.1)
2 3/4"
(7.0)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
clearance to wall for pan removal. If the 90˚ door stop position is used, pan access is
OVERALL DIMENSIONS
36" (91.5)
ZIRS360NHRHMONOGRAM 36" BUILT-IN ALL-REFRIGERATOR
2 3/4"
(7.0)
25 3/4" (65.4)
23 7/8" (60.7)
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/4" (65.41 cm)
Door Clearance 36 3/4" (93.4 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
Shipping Weight 569 lb
(212.1 - 214.6 cm)
tubing or GE
SmartConnect kit
64 1/4"
(163.2)
*6 1/2"
(16.5)
*73 1/4"
(186.1)
*84"
(213.4)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
35" (89.0)
Case width
** Allow 25" (63.5) min
clearance for 130˚
door swing
*3 1/2"
(8.9)
SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
36 3/4"
recessed into the back wall.
**These units are equipped with a 2-position door stop. The factory set 130° door swing can
be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Allow 15" minimum
Dimensions in parentheses are in centimeters unless otherwise noted. Actual
product dimension may vary due to manufacturing tolerances.
(93.4)
TOP VIEW
4" (10.2) min
** Allow
clearance to a wall
for 90˚ door swing
Product Specification Revised 1/18
ZIRS360NHRHMONOGRAM 36" BUILT-IN ALL-REFRIGERATOR
35 1/2" (90.2)
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75
1/2
"
(191.8)
From floor
to bottom
of electrical
area
ELEC.
5 1/2"
(14.0)
9"
(22.9)
SIDE VIEW
W
FRONT VIEW
7/16"
(1.1)
Trim overlap
24" (61.0 )
2"
(5.1)
4 3/4"
(12.1)
3 1/2"
(8.9)
WITH ANTI-TIP BRACKET
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
WITH ANTI-TIP BRACKET
STANDARD INSTALLATION
2 5/16"
(5.9)
ELEC.
10"
(25.4)
*83 1/2" min
*84 1/2" max
*Trim will overlap
additional 7/16"
(212.1-214.6)
5"
(12.7)
ANTI-TIP BRACKET
SIDE VIEW INSTALLED
35 1/2" (90.2)
A
5 1/2"
(14.0)
B
WATER
3 1/2"
(9.0)
81 1/2"
(207.0)
5"
(12.7)
From floor
to bottom
of electrical
3 1/2"
(8.9)
75"
(190.5)
area
additional hole
locations at end
of brackets
4"
(10.2)
mounted
into vertical
wall studs
Ensure holes
selected are
centered on
Use two
the studs
FRONT VIEW OF CUTOUT
C
L
Bracket
Wall
Studs
24" (61.0 )
2"
(5.1)
W
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
NOTES
A
Mounting the junction
box in this location
will also allow for front
accessibility through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 1/2" from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32 1/2"
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings in
back of the unit. The unit
will be secured to the
bracket using supplied
“L” bolts.
See Installation Instructions
for detailed instructions.
Product Specification Revised 1/18
Loading...