GE Monogram® 36" Built-In All-Refrigerator
36" (91.5)
2 3/4"
(7.0)
*84"
(213.4)
*73 1/4"
(186.1)
30 1/2"
(77.5)
*31 3/4"
(80.6)
25 3/4" (65.4)
23 7/8" (60.7)
*3 1/2"
(8.9)
SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
35"
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
OVERALL DIMENSIONS
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/4" (65.41 cm)
Door Clearance 36 3/4" (93.4 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
Shipping Weight 569 lb
tubing or GE
SmartConnect kit
*84"
(213.4)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
36" (91.5)
** Allow 25" (63.5) min
clearance for 130˚
door swing
30 1/2"
(77.5)
*73 1/4"
*31 3/4"
(80.6)
(186.1)
(89.0)
Case width
ZIRP360NHLH
25 3/4" (65.4)
23 7/8" (60.7)
2 3/4"
(7.0)
*83 1/2"
(212.1)
*3 1/2"
(8.9)
SIDE VIEWFRONT VIEW
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
TOP VIEW
36 3/4"
(93.4)
** Allow 5" (12.7) min
clearance to a wall
for 90˚ door swing
**These units are equipped with a 2-position door stop. The factory set 130° door swing can
be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Allow 15" minimum
clearance to wall for pan removal. If the 90˚ door stop position is used, pan access is
maintained but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimension may vary due to manufacturing tolerances.
Product Specification Created 6/14
35 1/2" (90.2)
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75
1/2
"
(191.8)
From floor
to bottom
of electrical
area
ELEC.
5 1/2"
(14.0)
9"
(22.9)
SIDE VIEW
W
FRONT VIEW
7/16"
(1.1)
Trim overlap
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
3 1/2"
(8.9)
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
GE Monogram® 36" Built-In All-Refrigerator
ZIRP360NHLH
STANDARD INSTALLATION
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
ANTI-TIP BRACKET
35 1/2" (90.2)
ELEC.
9"
(22.9)
5"
(12.7)
A
5 1/2"
(14.0)
WATER
3 1/2"
(9.0)
B
81 1/2"
(207.0)
5"
(12.7)
75
From floor
to bottom
of electrical
3 1/2"
(8.9)
1/2
"
(191.8)
area
Use two
additional hole
locations at end
of brackets
4 3/4"
(12.1)
Bracket
mounted
into vertical
wall studs
Ensure holes
selected are
centered on
the studs
Wall
Studs
24" (61.0)
2"
(5.1)
C
L
W
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
NOTES
A
Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
See Installation
Instructions for detailed
instructions.
Product Specification Created 6/14
GE Monogram® 36" Built-In All-Refrigerator
ZIRP360NHLH
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
*84”
*84"
(213.4)
(213.4)
*Depending
*Depending
on installation
on installation
height
NOTES
F
Side panels must be
used whenever the sides
of the refrigerator will
be exposed. The 1/4”
side panels will slip
into the side case trim.
Secure the panels to
the refrigerator with
stick-on hook and loop
fastener strips. Order
the side panels from the
cabinet manufacturer.
2 9/16"
(6.5)
Product Specification Created 6/14
GE Monogram® 36" Built-In All-Refrigerator
71 1/2" (181.6)
Finished Width
24" (61.0)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
5 1/2"
(13.9)
9"
(22.9)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC.
5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7)
5"
(12.7)
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
ZIRP360NHLH
DUAL INSTALLATIONS
2 5/16"
(5.9)
ELEC.
9"
(22.9)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
5"
(12.7)
5 1/2"
WATER
3 1/2"
(9.0)
A
71 1/2" (181.6)
Finished Width
(13.9)
(12.7)
FRONT VIEW
5"
5"
(12.7)
ELEC.
9"
(22.9)
WATER
24 3/16" (61.4)
5 1/2"
(13.9)
3 1/2"
(9.0)
5"
(12.7)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
3 1/2"
(8.9)
area
24" (61.0)
Min. Cutout Depth
SIDE VIEW
NOTES
A
A separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
Additional cutout width may be required when
side panels are used.
B
In a side-by-side installation of a left-
and-right-hand door swing product, 1”
clearance between the units is required.
Order ZUGSS2 European, ZUGPP2
Professional or ZUG2 custom panel unified
grille kit for one continuous grille panel.
C
In a side-by-side installation with same
door swing, allow 2” minimum clearance
between the products to prevent the door
swing interference. Allow 15” minimum
to a wall to achieve full drawer extension
and pan removal. Additional clearances
are required when using custom panels
and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille
panel kits will not fit this installation.
3 1/2"
(8.9)
W
D
In a side-by-side installation with right
and left door hinges together, allow 5”
minimum clearance between the two
products to prevent one door from striking
the other. Additional clearances required
when using custom panels and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille
panel kits will not fit this installation.
DUAL PRODUCT CLEARANCES
25" (63.5) min
To wall
1"
(2.5)
130˚
Door swing
B C
130˚
Door swing
25" (63.5) min
To wall
5" (12.7) min
2" min
(5.1)
15"
(38.1) min
To wall
D
Product Specification Created 6/14
GE Monogram® 36" Built-In All-Refrigerator ZIRP360NHLH
FEATURES AND BENEFITS
Stainless Exterior - Conveys a sense of solidity
and beauty with tubular handles, louvered grille
and chamfered, hand-finished edges
Enhanced Temperature Management System With precise electronic controls and thermistors,
maintains ideal storage conditions for fresh foods
Concealed Halogen Lighting System Illuminates contents without compromising space
®
ENERGY STAR
STAR® partner, GE has determined that Monogram
all-refrigerators meet the ENERGY STAR
guidelines for energy efficiency
Humidity-Controlled Compartments and
Sealed Snack Drawers - Help preserve the
freshness of foods
Qualification - As an ENERGY
®
Adjustable Spillproof Glass Shelves - Easily
accommodate party trays and platters
Sealed Dairy Compartment - Locks in freshness
Gallon-Size Door Bin - Holds milk containers,
two-liter bottles and pitchers
R
Product Specification Created 6/14
Loading...