SECTION 1
FLUSH INSET INSTALLATION
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
SECTION 2
STANDARD INSTALLATION
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
Product Specification Revised 10/14
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
SPECIFICATIONS
Overall Width 38" (96.5 cm)
Overall Height 83 1/2" (212.1 cm)
Overall Depth 25 7/8" (65.7 cm)
Door Clearance 38 3/4" (98.4 cm)
Cutout Width 39" (99.1 cm)
Cutout Height 84 1/2" (214.6 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 570 lb (258.5 kg)
†
OVERALL DIMENSIONS
FLUSH INSET INSTALLATION
25 7/8" (65.7)
*3"
(7.6)
20 5/8" (52.4)
* 83 1/2"
(212.1)
SIDE VIEW
38" (96.5)
10 5/16"
(26.2)
69 13/16"
(177.3)
*73 1/4"
(186.1)
*3 3/8"
** Allow 17" (43.2) min
clearance for 115˚
door swing
(8.6)
*83 1/2"
(212.1)
†
†
FRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”
35" (89.0)
Case width
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
TOP VIEW
38 3/4"
(98.4)
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
Product Specification Revised 10/14
FLUSH INSET INSTALLATION 3/4" PANELS
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16"
(1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
6"
(15.2)
10"
(25.4)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
FLUSH INSET INSTALLATION 3/4" PANELS
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
84 1/2"
(214.6)
Finished cleats
3 1/2"
(8.9)
W
ANTI-TIP BRACKET
81 1/2"
(207.0)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
5 1/4" (13.3)
3/4" (1.9)
Width of side cleats
84 1/2"
(214.6)
Use two
additional hole
locations at end
of brackets
TOP VIEW
Case
Finished cleats
Case Trim
Door
3/4" Panel
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
ELEC.
9"
(22.9)
5 1/2"
(14.0)
26 3/16"
(66.5)
B
7"
(17.8)
WATER
3 1/2"
(9.0)
7"
(17.8)
FRONT VIEWSIDE VIEW
C
L
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
Ensure holes
selected are
centered on
the studs
Wall
Studs
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
1/2" (1.3)
(190.5 )
From floor
to bottom
of electrical
3 1/2"
(8.9)
A
75"
area
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
FLUSH INSET INSTALLATION
NOTES
NOTES
A
Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
See Installation
Instructions for detailed
instructions.
Product Specification Revised 10/14
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
A
Grille Panel
B
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
1/4" Router Cut Depth
for Hinge Clearance
Door
HINGE CLEARANCES
ROUTER 1/4" DEEP
Door
Panel
FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
C
Z
Y
PANEL DIMENSIONS
A B C
38" 9 5/8" 69 13/16"
A
X
HINGE CLEARANCE
1 1/4" 1" 1/2"
PANEL DIMENSIONS
X Y Z
FLUSH INSET INSTALLATION
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels. Fieldinstalled custom door and grille panels
are required.
Adjustment brackets allow 1/8” ne
adjustment of panel position in 3
dimensions.
Use templates provided to locate mounting
brackets on the door and grille panels.
Maximum total panel weight:
• Fresh food door panels – 67 lbs.
• Grille panel – 11 lbs
Door Handles
Door handles not included. Custom handle
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4” panels. Kit includes
one handle – 30 1/2” long.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4” panels. Kit includes
one handle – 64 1/4” long.
Order #ZUGF2H: Unified grille kit for dual
installation. Maximum total panel weight -
25 lbs.
NOTE: For side-by-side installation of a leftand-right-hand door swing product only,
see
on following page.
B
D
Door
Panel
Grille Panel
D
Door
Panel
B
A B C D
74 1/2" 9 5/8" 69 13/16" 37"
HINGE CLEARANCE
X Y Z
1 1/4" 1" 1/2"
HINGE CLEARANCES
C
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
ROUTER 1/4" DEEP
Z
Y
1/4" Router Cut Depth
for Hinge Clearance
Door
X
Product Specification Revised 10/14
Loading...